The purpose of this research is to investigate and characterize the W-Ni-Fe-Ta compositions by solid-state sintering using the Spark Plasma Sintering (SPS) technique at a relatively lower temperature. The sinterability of W-Ni-Fe ternary tungsten heavy alloy (WHA) with the addition of Tantalum in predetermined compositions was sintered using SPS at 1100°C under 30 MPa pressure. The effect of Ta addition on WHA densification, microstructure, and mechanical properties was studied. Ni was found to act as an activator in the sintering of tungsten. SEM and energy dispersive spectroscopy revealed an even distribution of Ta in the W and Ni-Fe matrix. The data of hardness and ultimate tensile strength were explained using grain size, contiguity, and the formation of brittle intermetallic phases. W-7Ni-3Fe-5Ta alloy composition has the highest ultimate tensile strength of 870 MPa, 189.2 HV0.5kgf hardness, and 83.42% relative sintered density. During the tensile test, W grain cleavage fracture, W-W decohesion, matrix tearing, and W matrix intergranular types of fracture surface were observed.
GermanRM.Microstructure and impurity effects on tungsten heavy alloys. Report, Materials Engineering Department, Rensselaer Polytechnic Institute Troy, New York, 12July1990. DOI: 10.21236/ada224220.
2.
YangS-CManiSSGermanRM.The effect of contiguity on growth kinetics in liquid-phase sintering. JOM1990; 42: 16–19.
3.
BoseAGermanRM.Matrix composition effects on the tensile properties of tungsten-molybdenum heavy alloys. Metall Trans1990; 21: 1325–1327.
4.
PosthillJBHogwoodMCEdmondsDV.Precipitation at tungsten/tungsten interfaces in tungsten–nickel–iron heavy alloys. Powder Metall1986; 29: 45–51.
5.
MuddleBC.Interphase boundary precipitation in liquid phase sintered W-Ni-Fe and W-Ni-Cu alloys. Metallurgical Mater Trans A1984; 15: 1089–1098.
6.
MagnessLSKapoorDDowdingR.Novel flow-softening and flow-anisotropy approaches to developing improved tungsten kinetic energy penetrator materials. Mater Manuf Process1995; 10: 531–540.
7.
RyuHJHongSHBaekWH.Microstructure and mechanical properties of mechanically alloyed and solid-state sintered tungsten heavy alloys. Mater Sci Eng A2000; 291: 91–96.
8.
HuKLiXQuS, et al. Spark-Plasma Sintering of W-5.6Ni-1.4Fe heavy alloys: densification and grain growth. Metallurgical Mater Trans A2013; 44: 923–933.
9.
HuKLiXGuanM, et al. Dynamic deformation behavior of 93W-5.6Ni-1.4Fe heavy alloy prepared by spark plasma sintering. Int J Refract Metals Hard Mater2016; 58: 117–124.
10.
UpadhyayaA.Processing strategy for consolidating tungsten heavy alloys for ordnance applications. Mater Chem Phys2001; 67: 101–110.
11.
MondalAUpadhyayaAAgrawalD.Effect of heating mode and sintering temperature on the consolidation of 90W–7Ni–3Fe alloys. J Alloys Comp2011; 509: 301–310.
12.
MabuchiMOkamotoKSaitoN, et al. Deformation behavior and strengthening mechanisms at intermediate temperatures in W-La2O3. Mater Sci Eng A1997; 237: 241–249.
13.
KimYDOhNLOhS-T, et al. Thermal conductivity of W–Cu composites at various temperatures. Mater Lett2001; 51: 420–424.
14.
Shu-dongLJian-hongYYing-LiG, et al. Microwave sintering W–Cu composites: analyses of densification and microstructural homogenization. J Alloys Comp2009; 473: L5–L9.
15.
KilicMOzyurekDTuncayT.Dry sliding wear behaviour and microstructure of the W–Ni–Fe and W–Ni–Cu heavy alloys produced by powder metallurgy technique. Powder Metall Met Ceram2016; 55: 54–63.
16.
ShudongLJianhongYTaihongW, et al. Study of 80W-10Ta-7Ni-3Fe high density alloys. Rare Metal Mater and Eng2005; 34: 226–230.
17.
BoseAGermanRM.Sintering atmosphere effects on tensile properties of heavy alloys. Metallurgical Trans A1988; 19: 2467–2476.
18.
XiangDPDingLLiYY, et al. Fabricating fine-grained tungsten heavy alloy by spark plasma sintering of low-energy ball-milled W–2Mo–7Ni–3Fe powders. Mater Sci Eng A2013; 578: 18–23.
19.
ŞahinY.Recent progress in processing of tungsten heavy alloys. J Powder Technol2014; 2014: 1–22.
20.
DingLXiangDPPanYL, et al. Mechanical properties and microstructural evolution of Mo–Co-co-strengthened W–Ni–Fe alloys by spark plasma sintering. J Alloys Comp2017; 712: 593–598.
21.
KiranURPanchalASankaranarayanaM, et al. Tensile and impact behavior of swaged tungsten heavy alloys processed by liquid phase sintering. Int J Refract Metals Hard Mater2013; 37: 1–11.
22.
MondalAAgrawalDUpadhyayaA.Microwave sintering of refractory metals/alloys: W, Mo, Re, W-Cu, W-Ni-Cu and W-Ni-Fe Alloys. J Microw Power Electromagn Energy2010; 44: 28–44.
23.
ZhangYHuangYLiuW, et al. Effect of tungsten tantalum pre-alloying on the sintering structure of 90(W-Ta)-Ni-Fe alloy. J Alloys Comp2022; 891: 161881.
24.
ASTM E407–07(2015). Standard practice for microetching metals and alloys. ASTM, 1999.
25.
GermanRMMunirZA.Enhanced low-temperature sintering of tungsten. Metallurgical Trans A1976; 7: 1873–1877.
26.
JohnsonJLGermanRM.Phase equilibria effects on the enhanced liquid phase sintering of tungsten-Copper. Metallurgical Mater Trans A1993; 24: 2369–2377.
27.
BoonyongmaneeratY.Effects of low-content activators on low-temperature sintering of tungsten. J Mater Process Technol2009; 209: 4084–4087.
28.
GongXFanJLDingF, et al. Effect of tungsten content on microstructure and quasi-static tensile fracture characteristics of rapidly hot-extruded W–Ni–Fe alloys. Int J Refract Metals Hard Mater2012; 30: 71–77.
29.
MondalAUpadhyayaAAgrawalD.Microwave and conventional sintering of 90W–7Ni–3Cu alloys with premixed and pre-alloyed binder phase. Mater Sci Eng A2010; 527: 6870–6878.
30.
DingLXiangDPLiYY, et al. Effects of sintering temperature on fine-grained tungsten heavy alloy produced by high-energy ball milling assisted spark plasma sintering. Int J Refract Metals Hard Mater2012; 33: 65–69.
31.
DasJAppa RaoGPabiSK.Microstructure and mechanical properties of tungsten heavy alloys. Mater Sci Eng A2010; 527: 7841–7847.
32.
PrabhuGChakrabortyASarmaB.Microwave sintering of tungsten. Int J Refract Metals Hard Mater2009; 27: 545–548.
33.
SagarCKPriyadarshiniAGuptaAK, et al. Experimental investigation of tool wear characteristics and analytical prediction of tool life using a modified tool wear rate model while machining 90 tungsten heavy alloys. Proc IMechE, Part B: J Engineering Manufacture2021; 235(1-2): 242–254.
34.
VeereshNCRameshMRDesaiV, et al. Sintering metal injection molding parts of tungsten-based steel using microwave and conventional heating methods. Proc IMechE, Part B: J Engineering Manufacture2019; 233(11): 2138–2146.
35.
YarrapareddyEZekovicSHamidS, et al. The development of nickel-tungsten carbide functionally graded materials by a laser-based direct metal deposition process for industrial slurry erosion applications. Proc IMechE, Part B: J Engineering Manufacture2006; 220(12): 1923–1936.
