Abrasive water jet (AWJ) drilling is a thermally benign method enabling damage-tolerant hole production in recyclable carbon fiber-reinforced polyetheretherketone (CF/PEEK) laminates. Using a Taguchi L18 orthogonal array, this study investigated the effects of traverse rate, water-jet pressure, and abrasive mass flow rate on surface roughness (Ra), kerf angle (θ), dimensional deviation (ΔD), and entry/exit delamination factors (Fd). To link process conditions with surface morphology, grey relational analysis (GRA) was integrated with the Taguchi method for multi-response optimization. The analysis revealed that damage mechanisms fundamentally evolve with traverse rate; lower speeds cause interlaminar delamination due to prolonged hydraulic loading, whereas higher speeds shift the damage to localized fiber fracture and erosion. Notably, entry-side delamination was consistently more severe than at the exit. The optimum parameter combination to minimize all defects simultaneously was identified as 1250 mm/min traverse rate, 2000 bar jet pressure, and 350 g/min abrasive mass flow rate. ANOVA confirmed traverse rate as the most dominant factor, contributing approximately 60% to the overall hole quality. Ultimately, this study establishes a robust process window for dimensionally accurate, low-damage AWJ drilling of CF/PEEK composites, highlighting the critical role of traverse speed in governing microscale damage transitions.
United Nations Environment Programme (UNEP). Global environment outlook – GEO-6: healthy planet, healthy people. UNEP, 2019. https://doi.org/10.1017/9781108627146
5.
International Organization for Standardization (ISO). ISO 14040:2006 environmental management — life cycle assessment — principles and framework. ISO, 2006.
6.
OliveuxGDandyLOLeekeGA. Current status of recycling of fibre reinforced polymers: review of technologies, reuse and resulting properties. Prog Mater Sci2015; 72: 61–99. https://doi.org/10.1016/j.pmatsci.2015.01.004
7.
FriedrichKAlmajidAA. Manufacturing aspects of advanced polymer composites for automotive applications. Appl Compos Mater2013; 20: 107–128. https://doi.org/10.1007/s10443-012-9258-7
KruegerRBerganA. Advances in thermoplastic composites over three decades. NASA Langley Research Center, 2024. NASA TM-2024-005376. https://ntrs.nasa.gov/citations/20240005376
CostaAPDBotelhoECCostaML, et al.A review of welding technologies for thermoplastic composites in aerospace applications. J Aero Technol Manag2012; 4: 255–265. https://doi.org/10.5028/jatm.2012.04033912
12.
OrnaghiHLJMonticeliFMAgnolLD. A review on polymers for biomedical applications on hard and soft tissues and prosthetic limbs. Polymers2023; 15: 4034. https://doi.org/10.3390/polym15194034
RathodDRathodMPatelR, et al.A review on strengthening, delamination formation and suppression techniques during drilling of CFRP composites. Cogent Eng2021; 8: 1941588. https://doi.org/10.1080/23311916.2021.1941588
15.
MeinhardDHaegerAKnoblauchV. Drilling induced defects on carbon fiber-reinforced thermoplastic polyamide and their effect on mechanical properties. Compos Struct2021; 256: 113138. https://doi.org/10.1016/j.compstruct.2020.113138
16.
ZhangXChenJWangH, et al.Mechanisms of defect formation and evolution in drilling thermoplastic CF/PEEK composite using twist and step drills. Compos Struct2025; 355: 118833. https://doi.org/10.1016/j.compstruct.2024.118833
17.
YuanWYangTLiuC, et al.Towards understanding the thermal characteristics of thermoplastic CF/PEEK composite drilling: heat transfer mechanism, crystallinity, and hole making performance. Int J Adv Manuf Technol2024; 130: 1075–1092. https://doi.org/10.1007/s00170-023-12741-y
18.
Díaz-ÁlvarezJMiguélezMHSantiusteC, et al.Theoretical estimation of thermal effects in drilling of woven CFRP. Materials2014; 7: 4443–4462. https://doi.org/10.3390/ma7064442
19.
SeoJBanerjeeNKimY, et al.Experimental and analytical investigation of the drilling forces of the carbon fiber reinforced plastics including thermal effects. J Manuf Process2020; 58: 1126–1137. https://doi.org/10.1016/j.jmapro.2020.08.063
20.
PoórDIGeierNPereszlaiC, et al.A critical review of the drilling of CFRP composites: burr formation, characterisation and challenges. Compos Part B Eng2021; 223: 109155. https://doi.org/10.1016/j.compositesb.2021.109155
21.
BolatÇKarakılınçUYalçınB, et al.Effect of drilling parameters and tool geometry on the thrust force and surface roughness of aerospace grade laminate composites. Micromachines2023; 14: 1427. https://doi.org/10.3390/mi14071427
YakutNÇakırO. Investigation of drilling CF/PEEK thermoplastic composites with varying helix angle drills and optimization of cutting parameters. J Thermoplast Compos Mater2025; 38: 1–20. https://doi.org/10.1177/08927057251371622
24.
JaiswalAParkHW. Comprehensive review of strategies to mitigate delamination and uncut fibers in CFRP drilling. Int J Precis Eng Manuf Smart Tech2025; 12: 1–25. https://doi.org/10.57062/ijpem-st.2025.00157
25.
MengZLiuSHuK, et al.A review on the cutting of carbon fiber reinforced thermoplastic composites. Polym Compos2024; 45: 1–28. https://doi.org/10.1002/pc.28748
26.
WangKWuSWangJ, et al.Drilling defects and process optimization in carbon fiber-reinforced polymer composites: a review. Coatings2026; 16(2): 204. https://doi.org/10.3390/coatings16020204
27.
VallejoJGarcía-PlazaENúñezPJ, et al.Machinability analysis of carbon fibre reinforced PET-glycol composites processed by additive manufacturing. Compos Appl Sci Manuf2023; 172: 107561. https://doi.org/10.1016/j.compositesa.2023.107561
28.
GeJLuoMZhangD, et al.Temperature field evolution and thermal-mechanical interaction induced damage in drilling of thermoplastic CF/PEKK–A comparative study with thermoset CF/epoxy. J Manuf Process2023; 88: 167–183. https://doi.org/10.1016/j.jmapro.2023.01.042
29.
ZhangXChenJLiH, et al.Research on the thermal-mechanical interaction of the defect evolution and surface generation during the drilling of thermoplastic composites. J Mater Res Technol2025; 37: 2834–2849. https://doi.org/10.1016/j.jmrt.2025.06.127
30.
TangHYangKLiZ, et al.Interlaminar failure behavior of continuous carbon fiber reinforced PEEK composites fabricated by additive manufacturing: role of failure modes and operating temperature. Polym Compos2026; 47(2): 1605–1617. https://doi.org/10.1002/pc.70239
31.
TangHYangKChenZ. Effect of operating temperature on the mechanical behavior of 3D printed continuous carbon fiber reinforced PEEK composites for space environments. Polym Compos2025; 46: S842–S855. https://doi.org/10.1002/pc.30002
32.
LuCXuCLuX, et al.Comparison and analysis of measurements for crystallinity of PEEK and CF/PEEK composites. Polym Compos2025; 46(8): 7120–7131. https://doi.org/10.1002/pc.29418
33.
XiongPZhouYZhouL, et al.The prediction of the effects of non-isothermal molding/reprocessing on the crystallinity and mechanical properties of PEEK and CF/PEEK. Sci Rep2025; 15(1): 16370. https://doi.org/10.1038/s41598-025-01018-x
34.
PathakSRMalikAMaliHS. Investigating effect of tool geometry on drilling performance of carbon fiber-reinforced polypropylene thermoplastic composite. J Thermoplast Compos Mater2025; 38(9): 3559–3584. https://doi.org/10.1177/08927057251318719
35.
SelvakumarSJMuralidharanSM. Performance analysis of drills with structured surfaces when drilling CFRP/AA7075 stack under MQL condition. J Manuf Process2023; 89: 194–219. https://doi.org/10.1016/j.jmapro.2023.01.053
36.
ArslaneMSlamaniMElhadiA, et al.Multi-response optimization of drilling parameters in hybrid natural fiber composites using taguchi and desirability function analysis (DFA). Int J Adv Manuf Technol2024; 135(11): 5631–5645. https://doi.org/10.1007/s00170-024-14855-3
37.
SorrentinoLTurchettaSBelliniC. A new method to reduce delaminations during drilling of FRP laminates by feed rate control. Compos Struct2018; 186: 154–164. https://doi.org/10.1016/j.compstruct.2017.12.005
38.
ÖzcanMVahapoğluKÖztürkG, et al.Evaluation of slot milling processes on carbon fiber reinforced polyetheretherketone thermoplastic composite utilizing nanofluid-enhanced minimum quantity lubrication technique. J Thermoplast Compos Mater2025; 38(11): 4329–4360. https://doi.org/10.1177/08927057251344136
39.
DanishMGuptaMKRubaieeS, et al.Machinability investigations on CFRP composites: a comparison between sustainable cooling conditions. Int J Adv Manuf Technol2021; 114(11): 3201–3216. https://doi.org/10.1007/s00170-021-07073-8
40.
CococcettaNMPearlDJahanMP, et al.Investigating surface finish, burr formation, and tool wear during machining of 3D printed carbon fiber reinforced polymer composite. J Manuf Process2020; 56: 1304–1316. https://doi.org/10.1016/j.jmapro.2020.04.025
41.
WuNZhangLZhangM, et al.Multi-objective optimization of ultrasonic vibration-assisted drilling in carbon fiber reinforced polyetherketoneketone laminate. Polym Compos2025; 46(4): 3595–3611. https://doi.org/10.1002/pc.29193
42.
YuanWLiuCYangT, et al.Enhanced tensile properties of drilled thermoplastic CF/PEEK composite laminate using heat treatment methods. J Appl Polym Sci2025; 142(21): e56912. https://doi.org/10.1002/app.56912
43.
GeJCatalanottiGFalzonBG, et al.Process characteristics, damage mechanisms and challenges in machining of fibre reinforced thermoplastic polymer (FRTP) composites: a review. Compos B Eng2024; 273: 111247. https://doi.org/10.1016/j.compositesb.2024.111247
44.
ThakurRKSinghKK. Abrasive waterjet machining of fiber-reinforced composites: a state-of-the-art review. J Braz Soc Mech Sci Eng2020; 42(7): 381. https://doi.org/10.1007/s40430-020-02463-7
45.
KartalF. Abrasive water jet machining of carbon fiber-reinforced PLA composites: optimization of machinability and surface integrity for high-precision applications. Polymers2025; 17(4): 445. https://doi.org/10.3390/polym17040445
46.
AlberdiAArtazaTSuarezA, et al.An experimental study on abrasive waterjet cutting of CFRP/Ti6Al4V stacks for drilling operations. Int J Adv Manuf Technol2016; 86(1): 691–704. https://doi.org/10.1007/s00170-015-8192-x
47.
DhakalHNIsmailSOOjoSO, et al.Abrasive water jet drilling of advanced sustainable bio-fibre-reinforced polymer/hybrid composites: a comprehensive analysis of machining-induced damage responses. Int J Adv Manuf Technol2018; 99(9): 2833–2847. https://doi.org/10.1007/s00170-018-2670-x
48.
ThongkaewKWangJYeohGH. An investigation of hole machining process on a carbon-fiber reinforced plastic sheet by abrasive waterjet. Adv Mater Res2016; 1136: 113–118. https://doi.org/10.4028/www.scientific.net/AMR.1136.113
49.
ZhangYLiuDZhangW, et al.Damage study of fiber-reinforced composites drilled by abrasive waterjet—challenges and opportunities. Int J Adv Manuf Technol2022; 119(1): 41–55. https://doi.org/10.1007/s00170-021-08246-1
50.
LiaoYLiuXZhaoC, et al.Ultrasonic-vibration-assisted waterjet drilling of [0/45/−45/90]2s carbon-fiber-reinforced polymer laminates. Micromachines2023; 14(12): 2209. https://doi.org/10.3390/mi14122209
51.
VigneshwaranSUthayakumarMArumugaprabuV. Abrasive water jet machining of fiber-reinforced composite materials. J Reinforc Plast Compos2018; 37(4): 230–237. https://doi.org/10.1177/0731684417740771
52.
AzmirMAAhsanAKRahmahA. Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite. Int J Material Form2009; 2(1): 37–44. https://doi.org/10.1007/s12289-008-0388-2
53.
VarmaMChandranSVijay KumarV, et al.A comprehensive review on the machining and joining characteristics of natural fiber-reinforced polymeric composites. Polym Compos2024; 45(6): 4850–4875. https://doi.org/10.1002/pc.28148
54.
SubramaniKRathinasuriyanC. Investigation on abrasive water jet drilling hole features of UHMWPE. Surf Rev Lett2025; 32(11): 2450136. https://doi.org/10.1142/S0218625X24501361
55.
LiLXiaoNGuoC, et al.A study on processing defects and parameter optimization in abrasive suspension jet cutting of carbon-fiber-reinforced plastics. Materials2023; 16(22): 7064. https://doi.org/10.3390/ma16227064
56.
MurthyBRNMakkiEPottiSR, et al.Optimization of process parameters to minimize the surface roughness of abrasive water jet machined jute/epoxy composites for different fiber inclinations. J Compos Sci2023; 7: 498. https://doi.org/10.3390/jcs7120498
57.
DallalSEslamiBTiariS. Recent advances in PEEK for biomedical applications: a comprehensive review of material properties, processing, and additive manufacturing. Polymers2025; 17: 1968. https://doi.org/10.3390/polym17141968
MurthyBRNBeeduRBhatR, et al.Delamination assessment in drilling basalt/carbon fiber reinforced epoxy composite material. J Mater Res Technol2020; 9: 7427–7433. https://doi.org/10.1016/j.jmrt.2020.05.001
62.
TsaoCCHochengH. Taguchi analysis of delamination associated with various drills in drilling of composite material. Int J Mach Tool Manufact2004; 44: 1085–1094. https://doi.org/10.1016/j.ijmachtools.2004.02.019
63.
XuJGeierNShenJ, et al.A review on CFRP drilling: fundamental mechanisms, damage issues, and approaches toward high-quality drilling. J Mater Res Technol2023; 24: 9677–9707. https://doi.org/10.1016/j.jmrt.2023.05.023
64.
MurthyBRNRaoUSNaikN, et al.A study to investigate the influence of machining parameters on delamination in the abrasive waterjet machining of jute-fiber-reinforced polymer composites: an integrated Taguchi and response surface methodology (RSM) optimization to minimize delamination. J Compos Sci2023; 7: 475. https://doi.org/10.3390/jcs7110475
65.
RaoVDPMrudulaMGeethikaVN. Multi-objective optimization of parameters in abrasive water jet machining of carbon-glass fibre-reinforced hybrid composites. J Inst Eng (India) Ser D2019; 100: 55–66. https://doi.org/10.1007/s40033-019-00181-6
66.
DhanawadeAKumarS. Study on carbon epoxy composite surfaces machined by abrasive water jet machining. J Compos Mater2019; 53: 2909–2924. https://doi.org/10.1177/0021998318807278
67.
DhanawadeAKumarPKumarS. Experimental study on abrasive water jet machining of carbon epoxy composite. Adv Mater Process Technol2020; 6: 40–53. https://doi.org/10.1080/2374068X.2019.1703338
68.
LehockáDKlichJBotkoF, et al.Pulsating water jet erosion effect on a brass flat solid surface. Int J Adv Manuf Technol2018; 97: 1099–1112. https://doi.org/10.1007/s00170-018-1882-4
69.
MoenchMK. The effect of nylon and polyester peel ply surface preparation on the bond quality of composite laminates. Doctoral dissertation, University of Washington, 2013. https://hdl.handle.net/1773/24971
70.
MaliAYPawarPJ. Parametric optimisation of abrasive water jet machining of glass fibre reinforced plastic composite using non-dominated sorting genetic algorithm-II. Int J Metaheuristics (IJMHeur)2017; 6: 334–354. https://doi.org/10.1504/IJMHEUR.2017.086982
71.
VanALNguyenTT. Investigation and optimization of MQL system parameters in the roller-burnishing process of hardened steel. Stroj Vestn J Mech Eng2022; 68: 155–165. https://doi.org/10.5545/sv-jme.2021.7473
72.
Ruiz-GarcíaRMayuet AresPFVázquez-MartínezJM, et al.Influence of abrasive waterjet parameters on the cutting and drilling of CFRP/UNS A97075 and UNS A97075/CFRP stacks. Materials2019; 12: 107. https://doi.org/10.3390/ma12010107
73.
GeierNPereszlaiC. Analysis of characteristics of surface roughness of machined CFRP composites. Period Polytech - Mech Eng2020; 64: 67–80. https://doi.org/10.3311/PPme.14436
74.
Álvarez-AlcónMLópez de LacalleLNFernández-ZacaríasF. Multiple sensor monitoring of CFRP drilling to define cutting parameters sensitivity on surface roughness, cylindricity and diameter. Materials2020; 13: 2796. https://doi.org/10.3390/ma13122796
75.
WangQJiaX. Optimization of cutting parameters for improving exit delamination, surface roughness, and production rate in drilling of CFRP composites. Int J Adv Manuf Technol2021; 117: 3487–3502. https://doi.org/10.1007/s00170-021-07918-2
76.
SambrunoAGómez-ParraÁMárquezP, et al.Evaluation of peripheral milling and abrasive water jet cutting in CFRP manufacturing: analysis of defects and surface quality. Fibers2024; 12(10): 78. https://doi.org/10.3390/fib12100078
77.
RoweAPramanikABasakAK, et al.Effects of abrasive waterjet machining on the quality of the surface generated on a carbon fibre reinforced polymer composite. Machines2023; 11: 749. https://doi.org/10.3390/machines11070749
78.
MontesanoJBougheraraHFawazZ. Influence of drilling and abrasive water jet induced damage on the performance of carbon fabric/epoxy plates with holes. Compos Struct2017; 163: 257–266. https://doi.org/10.1016/j.compstruct.2016.12.007
79.
KumarKNBabuPD. Improving the machining performance of polymer hybrid composite by abrasive water jet machining for precise machining. Arabian J Sci Eng2024; 49: 15347–15366. https://doi.org/10.1007/s13369-024-09033-2
80.
BañonFSambrunoAGonzález-RoviraL, et al.A review on the abrasive water-jet machining of metal–carbon fiber hybrid materials. Metals2021; 11: 164. https://doi.org/10.3390/met11010164
HashishM. A modeling study of metal cutting with abrasive waterjets. J Eng Mater Technol1984; 106: 88–100. https://doi.org/10.1115/1.3225682
83.
ShanmugamDKNguyenTWangJ. A study of delamination on graphite/epoxy composites in abrasive waterjet machining. Compos Part A Appl Sci Manuf2008; 39: 1848–1856. https://doi.org/10.1016/j.compositesa.2008.09.001
BañonFSambrunoABatistaM, et al.Study of the surface quality of carbon fiber–reinforced thermoplastic matrix composite (CFRTP) machined by abrasive water jet (AWJM). Int J Adv Manuf Technol2020; 109: 3087–3098. https://doi.org/10.1007/s00170-020-05215-y
86.
Altın KarataşMMotorcuARGökkayaH. Study on delamination factor and surface roughness in abrasive water jet drilling of carbon fiber-reinforced polymer composites with different fiber orientation angles. J Braz Soc Mech Sci Eng2021; 43: 308. https://doi.org/10.1007/s40430-020-02741-4
87.
UndePDGayakwadMDPatilNG, et al.Experimental investigations into abrasive waterjet machining of carbon fiber reinforced plastic. JEC Compos2015; 2015: 971596–971599. https://doi.org/10.1155/2015/971596
88.
SaraçyakupoğluT. The research of the delamination formation regarding pressure change in cutting with abrasive water jet (AWJ) for carbon fiber reinforced polymer (CFRP) materials. In: ÖzcanTDörtbudakMY (eds). Proc 2nd Int Sci Innov Congr. IKSAD Publishing House, 2021, pp. 413–423.
89.
SourdXGiasinKZitouneR, et al.Multi-scale analysis of the damage and contamination in abrasive water jet drilling of GLARE fibre metal laminates. J Manuf Process2022; 84: 610–621. https://doi.org/10.1016/j.jmapro.2022.10.023
90.
BhowmikSJagadishRA. Abrasive water jet machining of composite materials. In: Advanced manufacturing technologies: modern machining, advanced joining, sustainable manufacturing. Springer International Publishing, 2017. https://doi.org/10.1007/978-3-319-56099-1_4
91.
DahiyaAKBhuyanBKKumarS. Abrasive water jet machining of glass fibre reinforced polymer composite: experimental investigation, modelling and optimization. Int J Interact Des Manuf2023; 17(4): 1933–1947. https://doi.org/10.1007/s12008-023-01312-w
92.
DasLNayakRSaxenaKK, et al.Determination of optimum machining parameters for face milling process of Ti6Al4V metal matrix composite. Materials2022; 15: 4765. https://doi.org/10.3390/ma15144765
93.
PathakSRMalikAMaliHS. Optimization of input parameters during drilling of glass fiber reinforced polymer composite using grey relational analysis. Int J Interact Des Manuf2024; 18: 4075–4091. https://doi.org/10.1007/s12008-024-01900-4
94.
GopalPMKavimaniVArunkumarK. Multi-objective optimization on abrasive water jet machining of epoxy/glass fiber/grinding wheel particle composite through hybrid optimization technique. Multi and Multidiscipl Modeling, Exper and Des2023; 6(4): 697–707. https://doi.org/10.1007/s41939-023-00177-6
95.
ArunkumarKGopalPMKavimaniV. Influence of basalt and graphene fillers and their hybridization on surface quality during AWJM process. Mater Manuf Process2021; 36(11): 1314–1323. https://doi.org/10.1080/10426914.2021.1945098
96.
KrishnamoorthyABoopathySRPalanikumarK, et al.Application of grey fuzzy logic for the optimization of drilling parameters for CFRP composites with multiple performance characteristics. Measurement2012; 45: 1286–1296. https://doi.org/10.1016/j.measurement.2012.01.008
97.
ShunmugeshKPanneerselvamK. Grey relational analysis based optimization of multiple responses in drilling of carbon fiber-epoxy composites. Mater Today Proc2017; 4: 2861–2870. https://doi.org/10.1016/j.matpr.2017.02.166
98.
ZhujaniFAbdullahuFTodorovG, et al.Optimization of multiple performance characteristics for CNC turning of Inconel 718 using Taguchi–grey relational approach and analysis of variance. Metals2024; 14: 186. https://doi.org/10.3390/met14020186
99.
TsaiYYHoJKWangWH, et al.Grey-Taguchi-based optimization of wire-sawing for a slicing ceramic. Processes2020; 8: 1602. https://doi.org/10.3390/pr8121602
