Determining method of optimal process parameters using Taguchi method and technique for order preference by similarity to ideal solution in plastic injection molding

Abstract

Many plastic injection molding (PIM) process optimization problems are multi-objective optimization problems that optimize multiple mechanical properties. This paper proposed a determining method of optimal process parameters and their effect ranks using Taguchi method and TOPSIS in the PIM. TOPSIS was used to convert multiple mechanical properties into single comprehensive response. It was selected as a reasonable multi-attribute decision-making (MADM) method from among some well-known MADM methods based on mean rank correlation coefficient and mean absolute rank deviation. Taguchi method was used to design experiment and find the optimal process parameters. The proposed method was applied to determine the optimal values of the process parameters: melt temperature (MT), packing pressure (PP), cooling time (CT), and injection pressure (IP) for improving tensile strength, elasticity module, flexural modulus, and impact strength in the PIM with Acrylonitrile-Butadiene-Styrene compound as plastic materials and AISI 1020 as mold materials. The optimal values of the process parameters were MT of 280°C, PP of 28 MPa, CT of 22 s, and IP of 50 MPa, and their effect ranking was IP (51.941%), PP (32.280%), CT (9.045%), and MT (6.734%). The method could be widely applied to not only the PIM process optimization but also various manufacturing process optimization problems.

Keywords

Comprehensive response multi-objective optimization plastic injection molding Taguchi method TOPSIS

Get full access to this article

View all access options for this article.

References

Gao

Zhang

, et al. Process parameters optimization using a novel classification model for plastic injection molding. Int J Adv Manuf Technol 2018; 94: 357–370.

Kashyap

Datta

. Process parameter optimization of plastic injection molding: a review. Int J Plast Technol 2015; 19: 1–18.

Chen

Nguyen

Chiu

, et al. Optimization of the plastic injection molding process using the Taguchi method, RSM, and hybrid GA-PSO. Int J Adv Manuf Technol 2016; 83: 1873–1886.

Yan

Zhong

, et al. Multi-objective optimization of the fiber-reinforced composite injection molding process using Taguchi method, RSM, and NSGA-II. Simulat Model Pract Theor 2018; 91: 69–82. DOI: 10.1016/j.simpat.2018.09.003.

Yang

Kim

, et al. Multi-attribute optimization and influence assessment methodology of casting process parameters combined with integrated MADM and Taguchi method. Int J Adv Manuf Technol. 2023; 129(1): 681–695. DOI: 10.21203/rs.3.rs-3113560/v1.

Ashwani

Kumar

. Optimization of process parameters in injection-molding by recent methods for optimization – literature review. International Journal of Management, Technology And Engineering 2018; 8(V): 141–152.

Bensingh

Machavaram

Boopathy

, et al. Injection molding process optimization of a bi-aspheric lens using hybrid artificial neural networks (ANNs) and particle swarm optimization (PSO). Measurement 2019; 134: 359–374.

Kitayama

Tamada

Takano

, et al. Numerical optimization of process parameters in plastic injection molding for minimizing weldlines and clamping force using conformal cooling channel. J Manuf Process 2018; 32: 782–790.

Ozcelik

Ozbay

Demirbas

. Influence of injection parameters and mold materials on mechanical properties of ABS in plastic injection molding. Int Commun Heat Mass Tran 2010; 37: 1359–1365.

10.

Bashiri

Hejazi

. An extension of multi-response optimization in MADM view. J Appl Sci 2009; 9(9): 1695–1702.

11.

Fung

Huang

Doong

. The study on the optimization of injection molding process parameters with gray relational analysis. J Reinforc Plast Compos 2003; 22(1): 51–66.

12.

Kuo

C-FJ

T-L

. Optimization of multiple quality characteristics for polyether ether ketone injection molding process. Fibers Polym 2006; 7(4): 404–413.

13.

Tzeng

Yang

Hsieh

, et al. Adaptive adjustment of injection molding process for mechanical characteristics using the Taguchi method and response surface methodology. Polym-Plast Technol Eng 2011; 50(6): 552–563.

14.

Kitayama

Yamazaki

Takano

, et al. Numerical and experimental investigation of process parameters optimization in plastic injection molding using multi-criteria decision making. Simulat Model Pract Theor 2018; 85: 95–105. DOI: 10.1016/j.simpat.2018.04.004.

15.

Moayyedian

Mamedov

. Multi-objective optimization of injection molding process for determination of feasible moldability index. Procedia CIRP 2019; 84: 769–773.

16.

Mehat

Noor

Kamaruddin

. Optimization of multiple quality characteristics for injection moulded polyamide helical gear via integration of Taguchi method and Grey relational analysis. IOP Conf Ser Mater Sci Eng 2020; 932: 1–8. DOI: 10.1088/1757-899X/932/1/012122.

17.

Moayyedian

Dinc

Mamedov

. Optimization of injection-molding process for thin-walled polypropylene Part Using artificial neural network and Taguchi techniques. Polymers 2021; 13: 4158. DOI: 10.3390/polym13234158.

18.

Farooque

Rizvi

SJA

Asjad

. Screening design of process parameters for Isotactic polypropylene by Injection moulding process. International Journal for Research in Engineering Application & Management 2022; 8(6): 108–114.

19.

Pachorkar

Singh

Agarwal

, et al. Multi response optimization of injection moulding process to reduce sink marks and cycle time. Mater Today Proc 2022; 72: 1089–1093. DOI: 10.1016/j.matpr.2022.09.172.

20.

Chen

Cui

Liu

, et al. Design and parametric optimization of the injection molding process using statistical analysis and numerical simulation. Processes 2023; 11(414): 414–417. DOI: 10.3390/pr11020414.

21.

ASTM International . Standard test method for tensile properties of plastics. ASTM international, 2014.

22.

Hwang

Yoon

. Multiple attribute decision making: methods and applications. New York, NY: Springer-Verlag, 1981.

23.

Yang

Choe

Kim

, et al. Materials selection method using improved TOPSIS without rank reversal based on linear max-min normalization with absolute maximum and minimum values. Mater Res Express 2021; 9: 065503.

24.

Yang

Chon

Choe

, et al. Materials selection method using TOPSIS with some popular normalization methods, Eng Res Express 2021; 3: 1–10.

25.

Yang

, et al. Materials selection criteria weighting method using analytic hierarchy process (AHP) with simplest questionnaire and modifying method of inconsistent pairwise comparison matrix. Proc IMechE Part L: Journal of Materials: Design and Applications 2022; 236(1): 69–85.