High-entropy alloys due to their tunable properties, superior corrosion resistance, and exceptional strength can be used as potential reinforcements in composites. In the present study, FeCoNiMnCr HEA sub-micron particles were used as fillers in the epoxy matrix to fabricate epoxy-HEA composites. These novel composite combinations were studied for their density, water absorption, microhardness and tensile properties. Metal powders of Fe, Co, Ni, Mn and Cr were mechanically alloyed in an equi-atomic ratio for 15 h to produce face-centred cubic (FCC) structured HEA particulates. The epoxy-HEA composites of different HEA concentrations (0, 1, 2, 3 and 4 HEA wt. %) were prepared using hand lay-up process. The fabricated composites had good structural integrity with void content below 3%. The electron microscopy images showed sub-micron HEA particles homogenously dispersed in the epoxy matrix. Epoxy composite with 4 wt% HEA filler concentration showed an absorption rate of 0.86% for 192-h immersion. The composites showed improved mechanical properties as compared to neat epoxy. For the addition of 4 wt% HEA filler, the microhardness and tensile strength of the epoxy composite improved by 158% and 54%, respectively.
ZhouTWangXLiuX, et al.Improved thermal conductivity of epoxy composites using a hybrid multi-walled carbon nanotube/micro-SiC filler. Carbon2010; 48: 1171–1176.
5.
ZakariaMRAbdul KudusMHMd AkilH, et al.Improvement of fracture toughness in epoxy nanocomposites through chemical hybridization of carbon nanotubes and alumina. Materials2017; 10: 301.
6.
SalunkeDRGopalanV. Thermal and electrical behaviors of boron nitride/epoxy reinforced polymer matrix composite—a review. Polym Compos2021; 42: 1659–1669.
7.
AraujoFRosenbergHM. The thermal conductivity of epoxy-resin/metal-powder composite materials from 1.7 to 300K. J Phys D Appl Phys1976; 9: 665–675.
8.
JeyapragashRSrinivasanVSathiyamurthyS. Mechanical properties of natural fiber/particulate reinforced epoxy composites – a review of the literature. Mater Today Proc2020; 22: 1223–1227.
9.
ErkligAAlsaadiMBulutM. A comparative study on industrial waste fillers affecting mechanical properties of polymer-matrix composites. Mater Res Express2016; 3: 105302.
10.
MegahedMFathyAMorsyD, et al.Mechanical performance of glass/epoxy composites enhanced by micro-and nanosized aluminum particles. J Ind Textil2021; 51: 68–92.
11.
AtaberkN. The effect of Cu nanoparticle adding on to epoxy-based adhesive and adhesion properties. Sci Rep2020; 10: 11038.
12.
BaghdadiYNYoussefLBouhadirK, et al.The effects of modified zinc oxide nanoparticles on the mechanical/thermal properties of epoxy resin. J of Applied Polymer Sci2020; 137: 49330.
13.
ZhaiLLingGLiJ, et al.The effect of nanoparticles on the adhesion of epoxy adhesive. Mater Lett2006; 60: 3031–3033.
14.
JohnsenBBKinlochAJMohammedRD, et al.Toughening mechanisms of nanoparticle-modified epoxy polymers. Polymer2007; 48: 530–541.
15.
NjugunaJPielichowskiKAlcockJR. Epoxy‐based fibre reinforced nanocomposites. Adv Eng Mater2007; 9: 835–847.
MisiuraAIMamunyaYPKulishMP. Metal-filled epoxy composites: mechanical properties and electrical/thermal conductivity. J Macromol Sci, Part B: Phys2020; 59: 121–136.
18.
LuJMoonKSXuJ, et al.Synthesis and dielectric properties of novel high-K polymer composites containing in-situ formed silver nanoparticles for embedded capacitor applications. J Mater Chem2006; 16: 1543–1548.
19.
YuKCMaCCMTengCC, et al.Preparation and microwave absorbency of Fe/epoxy and FeNi3/epoxy composites. J Alloys Compd2011; 509: 8427–8432.
20.
QiLLeeBIChenS, et al.High‐dielectric‐constant silver–epoxy composites as embedded dielectrics. Adv Mater2005; 17: 1777–1781.
ChenTDengL. Thermal conductive and dielectric properties of epoxy resin with bimetal filler of Zn–Cu particle. J Mater Sci Mater Electron2019; 30: 9775–9784.
23.
MamunyaYPDavydenkoVVPissisP, et al.Electrical and thermal conductivity of polymers filled with metal powders. Eur Polym J2002; 38: 1887–1897.
24.
KavakNAltanE. Influence of filler amount and content on the mechanical performance of joints bonded with metal powder filled adhesive. Mater Sci Forum2013; 773: 226–233.
25.
DivyaGSSureshaB. Role of metallic nanofillers on mechanical and tribological behaviour of carbon fabric reinforced epoxy composites. Mater Sci Appl2018; 09: 740–750.
26.
ChenYWangLJiZ. Microstructural and mechanical investigations of extruded AlCrFeCoNi/AZ91D composites. J Mater Eng Perform2023; 32: 7275–7284.
27.
ZhuRLiYSunY, et al.Microstructure and properties of FeCoNiCrAl high-entropy alloy particle-reinforced Cu-matrix composites prepared via FSP. J Alloys Compd2023; 940: 168906.
28.
MurtyBSYehJWRanganathanS, et al.High-entropy alloys. 2nd ed.Amsterdam: Elsevier, 2019, p. 18.
29.
WangXGuoWFuY. High-entropy alloys: emerging materials for advanced functional applications. J Mater Chem A2021; 9: 663–701.
30.
LiuYChenJLiZ, et al.AlCoCrFeNi high entropy alloy reinforced Cu-based composite with high strength and ductility after hot extrusion. Vacuum2021; 184: 109882.
31.
ZhangYLeiGLuoK, et al.Tribological behavior of high-entropy alloy particle reinforced aluminum matrix composites and their key impacting factors. Tribol Int2022; 175: 107868.
32.
CantorBChangITHKnightP, et al.Microstructural development in equiatomic multicomponent alloys. Mater Sci Eng A2004; 377: 213–218.
33.
Laurent-BrocqMGoujonPAMonnierJ, et al.Microstructure and mechanical properties of a CoCrFeMnNi high entropy alloy processed by milling and spark plasma sintering. J Alloys Compd2019; 780: 856–865.
34.
VaidyaMGuruvidyathriKMurtyBS. Phase formation and thermal stability of CoCrFeNi and CoCrFeMnNi equiatomic high entropy alloys. J Alloys Compd2019; 774: 856–864.
35.
ManePJShantharajaMManneB, et al.Effect of FeCoNiMnCr high-entropy alloy reinforcement on mechanical, wear, and thermal expansion behavior of copper matrix composites. JOM2023; 75: 4421–4434.
36.
BoumedienneNFaskaYMaaroufiA, et al.Thermo-structural analysis and electrical conductivity behavior of epoxy/metals composites. J Phys Chem Solids2017; 104: 185–191.
AgrawalAChandrakarS. Influence of particulate surface treatment on physical, mechanical, thermal, and dielectric behavior of epoxy/hexagonal boron nitride composites. Polym Compos2020; 41: 1574–1583.
39.
SchuhBMendez-MartinFVölkerB, et al.Mechanical properties, microstructure and thermal stability of a nanocrystalline CoCrFeMnNi high-entropy alloy after severe plastic deformation. Acta Mater2015; 96: 258–268.
40.
KunoriTGeilPH. Morphology-property relationships in polycarbonate-based blends. II. Tensile and impact strength. J Macromol Sci, Part B: Phys1980; 18: 135–175.
41.
BritoZSanchezG. Influence of metallic fillers on the thermal and mechanical behaviour in composites of epoxy matrix. Compos Struct2000; 48: 79–81.
42.
GreenhalghE. Failure analysis and Fractography of polymer composites. 1st ed.New Delhi: Woodhead Publishing Limited, 2009, p. 165.
43.
GopePCSinghVKRaoDK. Mode I fracture toughness of bio-fiber and bio-shell particle reinforced epoxy bio-composites. J Reinf Plast Compos2015; 34: 1075–1089.
44.
GoyatMSSureshSBahlS, et al.Thermomechanical response and toughening mechanisms of a carbon nano bead reinforced epoxy composite. Mater Chem Phys2015; 166: 144–152.
