In this study, the effect of fiber orientation on the temperature history during the layup process is comprehensively investigated experimentally and numerically. Specimens with three different fiber orientations (i.e. [0°/0°/0°], [0°/45°/0°], and [0°/90°/0°]) are manufactured at two layup speeds and characterized for determining the degree of intimate contact and then calculating the thermal contact resistance. Then, an improved thermal model with thermal contact resistance is developed and validated to predict the temperature history accurately. The experimental results indicate that the degree of intimate contact decreases by increasing the difference in fiber orientation between the interfaces of successive plies, revealing a relationship between substrate fiber orientations and cooling rates. The effect of cooling rate on the degree of crystallinity is studied for all stacking configurations at two layup speeds and found that as the angle between the subsequent plies decreases, the cooling increases, leading to a drop in the degree of crystallinity. The outcomes of this study address the need for an improved thermal model approach for accurately predicting the thermal history of the manufactured composite by the laser-assisted fiber placement process.
OromiehieEPrustyBGCompstonP, et al.Automated fibre placement based composite structures: review on the defects, impacts and inspections techniques. Compos Struct2019; 224: 110987.
2.
YassinKHojjatiM. Processing of thermoplastic matrix composites through automated fiber placement and tape laying methods: a review. J Thermoplast Compos Mater2018; 31: 1676–1725.
Stokes-GriffinCMCompstonP. The effect of processing temperature and placement rate on the short beam strength of carbon fibre–PEEK manufactured using a laser tape placement process. Compos A Appl Sci Manuf2015; 78: 274–283.
6.
TierneyJGillespieJWJr. Modeling of in situ strength development for the thermoplastic composite tow placement process. J Compos Mater2006; 40: 1487–1506.
7.
LeónAArgerichCBarasinskiA, et al.Effects of material and process parameters on in-situ consolidation. Int J Mater Form2019; 12: 491–503.
8.
XiongHHamilaNBoisseP. Consolidation modeling during thermoforming of thermoplastic composite prepregs. Materials (Basel)2019; 12: 2853.
9.
YangFPitchumaniR. A fractal Cantor set based description of interlaminar contact evolution during thermoplastic composites processing. J Mater Sci2001; 36: 4661–4671.
10.
ComerAJRayDObandeWO, et al.Mechanical characterisation of carbon fibre–PEEK manufactured by laser-assisted automated-tape-placement and autoclave. Compos Part A Appl Sci Manuf2015; 69: 10–20.
11.
Stokes-GriffinCMCompstonP. An inverse model for optimisation of laser heat flux distributions in an automated laser tape placement process for carbon-fibre/PEEK. Compos Part A Appl Sci Manuf2016; 88: 190–197.
12.
RanganathanSAdvaniSGLamontiaMA. A non-isothermal process model for consolidation and void reduction during in-situ tow placement of thermoplastic composites. J Compos Mater1995; 29: 1040–1062.
13.
TierneyJGillespieJWJr. Modeling of heat transfer and void dynamics for the thermoplastic composite tow-placement process. J Compos Mater2003; 37: 1745–1768.
14.
BayerlTBrzeskiMMartínez-TafallaM, et al.Thermal degradation analysis of short-time heated polymers. J Thermoplast Compos Mater2015; 28: 390–414.
15.
SonmezFOHahnHT. Analysis of the on-line consolidation process in thermoplastic composite tape placement. J Thermoplast Compos Mater1997; 10: 543–572.
16.
Van HoaSDuc HoangMSimpsonJ. Manufacturing procedure to make flat thermoplastic composite laminates by automated fibre placement and their mechanical properties. J Thermoplast Compos Mater2017; 30: 1693–1712.
RayDComerAJLyonsJ, et al.Fracture toughness of carbon fiber/polyether ether ketone composites manufactured by autoclave and laser‐assisted automated tape placement. J Appl Polym Sci2014; 132: 41643. DOI: 10.1002/app.41643
19.
KokT. On the consolidation quality in laser assisted fiber placement: the role of the heating phase. Enschede, The Netherlands: University of Twente, 2018. DOI: 10.3990/1.9789036546065
20.
LevyAHeiderDTierneyJ, et al.Inter-layer thermal contact resistance evolution with the degree of intimate contact in the processing of thermoplastic composite laminates. J Compos Mater2014; 48: 491–503.
21.
KollmannsbergerALichtingerRHohenesterF, et al.Numerical analysis of the temperature profile during the laser-assisted automated fiber placement of CFRP tapes with thermoplastic matrix. J Thermoplast Compos Mater2018; 31: 1563–1586.
22.
LiZYangTDuY. Dynamic finite element simulation and transient temperature field analysis in thermoplastic composite tape lay-up process. J Thermoplast Compos Mater2015; 28: 558–573.
23.
ZhaoQHoaS VGaoZJ. Thermal stresses in rings of thermoplastic composites made by automated fiber placement process. Sci Eng Compos Mater2011; 18: 35–49.
24.
JeyakodiGT. Finite element simulation of the in-situ AFP process for thermoplastic composites using abaqus, 2016.
25.
TafreshiOAVan HoaSHoangDM, et al.Heat transfer by a moving heat source in automated fiber placement (AFP) thermoplastic composites manufacturing. In: Proceedings of the 4th International Symposium on Automated Composites Manufacturing, Montreal, 2019.
26.
ÇelikOHosseiniSMABaranI, et al.The influence of inter-laminar thermal contact resistance on the cooling of material during laser assisted fiber placement. Compos Part A Appl Sci Manuf2021; 145: 106367.
27.
ReichardtJBaranIAkkermanR. New analytical and numerical optical model for the laser assisted tape winding process. Compos Part A Appl Sci Manuf2018; 107: 647–656.
28.
Stokes-GriffinCMCompstonP. A combined optical-thermal model for near-infrared laser heating of thermoplastic composites in an automated tape placement process. Compos Part A Appl Sci Manuf2015; 75: 104–115.
29.
JiangJSuYZhouL, et al.Effect of nesting on the permeability of multilayer unidirectional fabrics. Appl Compos Mater2017; 24: 625–642.
30.
SasHSWurtzelEBSimacekP, et al.Effect of relative ply orientation on the through-thickness permeability of unidirectional fabrics. Compos Sci Technol2014; 96: 116–121.
31.
ÇelikOPeetersDDransfeldC, et al.Intimate contact development during laser assisted fiber placement: Microstructure and effect of process parameters. Compos Part A Appl Sci Manuf2020; 134: 105888.
32.
AgeorgesCYeLMaiY-W, et al.Characteristics of resistance welding of lap shear coupons. Part I: Heat transfer. Compos Part A Appl Sci Manuf1998; 29: 899–909.
33.
LeeW IlSpringerGS. A model of the manufacturing process of thermoplastic matrix composites. J Compos Mater1987; 21: 1017–1055.
34.
SchaeferPMGuglhoerTSauseMGR, et al.Development of intimate contact during processing of carbon fiber reinforced polyamide-6 tapes. J Reinf Plast Compos2017; 36: 593–607.
35.
BatistaNLOlivierPBernhartG, et al.Correlation between degree of crystallinity, morphology and mechanical properties of PPS/carbon fiber laminates. Mater Res2016; 19: 195–201.
36.
Quiroga CortesLCausséNDantrasE, et al.Morphology and dynamical mechanical properties of poly ether ketone ketone (PEKK) with meta phenyl links. J Appl Polym Sci2016; 133: 43396. DOI: 10.1002/app.43396
37.
Di FrancescoMVeldenzLDell’AnnoG, et al.Heater power control for multi-material, variable speed Automated Fibre Placement. Compos Part A Appl Sci Manuf2017; 101: 408–421.
38.
Stokes-GriffinCMCompstonP. Optical characterisation and modelling for oblique near-infrared laser heating of carbon fibre reinforced thermoplastic composites. Opt Lasers Eng2015; 72: 1–11.
39.
DanezisAWilliamsDEdwardsM, et al.Heat transfer modelling of flashlamp heating for automated tape placement of thermoplastic composites. Compos Part A Appl Sci Manuf2021; 145: 106381.
40.
Le LouetVRousseauBLe CorreS, et al.Directional spectral reflectivity measurements of a carbon fibre reinforced composite up to 450 C. Int J Heat Mass Transf2017; 112: 882–890.
41.
BatistaNLAnagnostopoulosKBotelhoEC, et al.Influence of crystallinity on interlaminar fracture toughness and impact properties of polyphenylene sulfide/carbon fiber laminates. Eng Fail Anal2021; 119: 104976.
42.
CousineauJS. Effect of Cooling Rate and Mold Counter Pressure on the Crystallinity and Foaming Control in Microcellular Injection Molded Polypropylene Parts. Wright State University, 2012.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
