This paper summarizes our work aimed at applying different methods sequentially in the evaluation of GFRP (glass fiber reinforced polyester) waste, which is a composite waste according to circular economy assumptions. For this aim, the management alternatives that are defined as mechanical recycling, chemical recycling, pyrolysis, and incineration methods are compared using the ANP (Analytic Network Process) and the VIKOR (Vise Kriterijumska Optimizacija I Kompromisno Resenje) methods. To show the applicability of the pyrolysis, which was determined as the most appropriate method, experiments were carried out at different temperatures. After the general characterization of the products was conducted, the solid product was used to reproduce GFRP. After a tensile strength test of the GFRP, which was produced using fibers obtained from pyrolysis at 500°C, it was found that it had approximately 43.15% more tensile strength than polyester cast without fiber. Following a further oxidation step, the tensile strength increased by 61.50%. The liquid products have the potential to be used as fuel oil, and the gas product is sufficient to provide the energy requirements of a process plant. Pyrolysis proved to be a profoundly feasible method for not only recovering glass fiber, but also energy from GFRP waste.
SimsGBishopG. UK polymer composites sector- Foresight Study and Competitive Analysis. Ireland: Manufacturing of Advanced Composites, 2001.
5.
KostopoulosVFotiouILoutasT. Recycling and reuse of glass-polyester composite materials. An experimental study. In: Proceedings of the polymer processing society 24th annual meeting-PPS-24, Salerno, Italy, 15 June - 19 June 2008.
6.
BledzkiAKSperberVTheisS, et al.Holzgefüllte thermoplaste als alternative fir naturholz. Gummi, Fasern, Kunststoffe1999; 52(4), 294–296.
7.
PalmerJ.Mechanical recycling of automotive composites for use as reinforcement in thermoset composites.PhD dissertation, UK: University of Exeter, 2009.
8.
YazdanbakhshABankLCTianY. Mechanical processing of GFRP waste into large-sized pieces for use in concrete. Recycling2018; 3(1), 2–11. DOI: 10.3390/recycling3010008
9.
DerosaRTelfeyanE. Current state of recycling sheet molding compounds and related materials. J Thermoplas Comp Mat2005; 18(3), 219–240. DOI: 10.1177%2F0892705705045006
10.
RahimizadehAKalmanJFayazbakhshK, et al.Mechanical and thermal study of 3D printing composite filaments from wind turbine waste. Polym Compos2021; 42(5):2305–2311. DOI: 10.1002/pc.25978
11.
PickeringSJ. Recycling technologies for thermoset composite materials current status, Composites: Part A2006; 37, 1206–1215. DOI: 10.1016/j.compositesa.2005.05.030
12.
TurnerTAWarriorNAPickeringSJ. Development of high value moulding compounds from recycled carbon fibres. Plast Rubber Compos2010; 39(3–5), 151–156. DOI: 10.1179/174328910X12647080902295
13.
YoonKY. Developing an extracting method of laminated glass-fiber for waste FRP boats regenerating. J Korean Soc Mar Environ Energy2008; 11(1), 50–54.
14.
DangWKubouchiMSembokuyaH, et al.Chemical recycling of glass fiber reinforced epoxy resin cured with amine using nitric acid. Polymer2005; 46: 1905–1912. DOI: 10.1016/j.polymer.2004.12.035
15.
ZabihiOAhmadiMLiuC, et al.Sustainable approach to the low-cost recycling of waste glass fibres composites towards circular economy. Sustainability2020;12(2):641. DOI: 10.3390/su12020641
16.
OliveuxGBailleulJLLa Salle, et al. Chemical recycling of glass fibre reinforced composites using subcritical water. Composites: Part A2012; 43(11), 1809–1818. DOI: 10.1016/j.compositesa.2012.06.008
17.
OkajimaISakoTJ. Recycling of carbon fiber-reinforced plastic using supercritical and subcritical fluids. Mater Cycles Waste Manage2017; 19, 15–20. DOI: 10.1007/s10163-015-0412-9
18.
KaoCCGhitaORHallamKR, et al.Mechanical studies of single glass fibres recycled from hydrolysis process using sub-critical water. Composites: Part A2012; 43, 398–406. DOI: 10.1016/j.compositesa.2011.11.011
19.
RahimizadehATahirMFayazbakhshK, et al.Tensile properties and interfacial shear strength of recycled fibers from wind turbine waste. Composites A2020; 1(131), 105786. DOI: 10.1016/j.compositesa.2020.105786
20.
WongKRuddCPickeringS, et al.Composites recycling solutions for the aviation industry. Sci China Technol Sci2017; 60(9), 1291–1300.
21.
CunliffeAMWilliamsPT. Characterisation of products from the recycling of glass fibre reinforced polyester waste by pyrolysis. Fuel2003; 82(18), 2223–2230. DOI: 10.1016/S0016-2361(03)00129-7
22.
GiorginiLLeonardiCMazzocchettiL, et al.Pyrolysis of fiberglass/polyester composites: recovery and characterization of obtained products. FME Trans2016; 44, 405–414.DOI: 10.5937/fmet1604405G
23.
VijayNRajkumaraVBhattacharjeeP. Assessment of composite waste disposal in aerospace industries. Proced Environ Sci2016; 35, 563–570. DOI: 10.1016/j.proenv.2016.07.041
24.
NilakantanGNuttS. Reuse and upcycling of aerospace prepreg scrap and waste. Reinforced Plastics2015; 59(1), 44–51. DOI: 10.1016/j.repl.2014.12.070
25.
GhardeSKandasubramanianB. Mechanothermal and chemical recycling methodologies for the Fibre Reinforced Plastic (FRP). Environ Technol Innovat2019; 14, 100311–100341. DOI: 10.1016/j.eti.2019.01.005
26.
GopalrajSKKarkiT. A review on the recycling of waste carbon fibre/glass fibre‐reinforced composites: fibre recovery, properties and life‐cycle analysis. SN Appl Sci2020; 2:433–454. DOI: 10.1007/s42452-020-2195-4
27.
NaqviSRPrabhakaraHMBramerEA, et al.A critical review on recycling of end-of-life carbon fibre/glass fibre reinforced composites waste using pyrolysis towards a circular economy. Resour Conserv Recycl2018; 136, 118–129. DOI: 10.1016/j.resconrec.2018.04.013
28.
KalkanisKPsomopoulosCSKaminarisS, et al.Wind turbine blade composite materials- End of life treatment methods. Energy Proced2019; 157, 1136–1143. DOI: 10.1016/j.egypro.2018.11.281
29.
MishraA. R.RaniP.PandeyK., et al. Novel multi-criteria intuitionistic fuzzy SWARA–COPRAS approach for sustainability evaluation of the bioenergy production process. Sustainability. 12(10), 4155 (2020) DOI: 10.3390/su12104155
30.
DeshpandePCSkaarCBrattebøH, et al.Multi-criteria decision analysis (MCDA) method for assessing the sustainability of end-of-life alternatives for waste plastics: a case study of Norway. Sci Total Environ2020; 719, 137353. DOI: 10.1016/j.scitotenv.2020.137353
31.
AlaoMAAyodeleTROgunjuyigbeASO, et al.Multi-criteria decision based waste to energy technology selection using entropy-weighted TOPSIS technique: the case study of Lagos, Nigeria. Energy2020; 201, 117675. DOI: 10.1016/j.energy.2020.117675
32.
KujluRMoslemzadehMRahimiS, et al.Selecting the best stabilization/solidification method for the treatment of oil-contaminated soils using simple and applied best-worst multi-criteria decision-making method. Environ Pollut2020; 263, 114447. DOI: 10.1016/j.envpol.2020.114447
33.
ÖzdemirAÖzkanAGünkayaZ, et al.Decision-making for the selection of different leachate treatment/management methods: the ANP and PROMETHEE approaches. Environ Sci Pollut Res2020; 27(16), 19798–19809. DOI: 10.1007/s11356-020-08524-7
34.
LuCYouJXLiuHC, et al.Health-care waste treatment technology selection using the interval 2-tuple induced TOPSIS method. Int J Environ Res Public Health2016; 13(6), 562. DOI: 10.3390/ijerph13060562
35.
YapHYNixonJD. A multi-criteria analysis of options for energy recovery from municipal solid waste in India and the UK. Waste Manage2015; 46, 265–277. DOI: 10.1016/j.wasman.2015.08.002
36.
Sauri-RianchoMRCabanas-VargasDDEcheverría-VictoriaM, et al.Locating hazardous waste treatment facilities and disposal sites in the State of Yucatan, Mexico. Environ Earth Sci2011; 63(2), 351–362. DOI: 10.1007/s12665-010-0706-0
37.
BanarMKoseBMOzkanA, et al.Choosing a municipal landfill site by analytic network process. Environ Geology2007; 52(4), 747–751. DOI: 10.1007/s00254-006-0512-x
38.
DelvereIIltinaMShanbayevM. et al.Evaluation of polymer matrix composite waste recycling methods. Environ Clim Technol2019; 23(1), 168–187. DOI: 10.2478/rtuect-2019-0012
39.
SaatyTL. Decision making with the analytic hierarchy process. Int J Serv Sci2008; 1(1):83–98. DOI: 10.1504/IJSSci.2008.01759
40.
SaatyTL. Decision making with dependence and feedback: the analytic network process. 2nd ed.Pittsburgh, USA: RWS Publications, 4922 Ellsworth Avenue, 2001.
41.
Razavi ToosiSLSamaniJMV. Evaluating water transfer projects using analytic network process (ANP). Water Resour Manage2012; 26, 1999–2014. DOI: 10.1007/s11269-012-9995-2
42.
OpricovicS. Multicriteria optimization of civil engineering systems. Belgrade: Faculty of Civil Engineering, 1998; vol. 2(1), pp. 5–21.
43.
TorresAde MarcoICaballeroBM, et al.GC-MS analysis of the liquid products obtained in the pyrolysis of fibre-glass polyester sheet moulding compound. J Anal Appl Pyrolysis2001; 58, 189–203. DOI: 10.1016/S0165-2370(00)00122-4
44.
PickeringSJKellyRMKennerleyJR, et al.A fluidised-bed process for the recovery of glass fibres from scrap thermoset composites. Compos Sci Technol2000; 60(4), 509–523. DOI: 10.1016/S0266-3538(99)00154-2
45.
TchobanoglousG. Solid waste management. Environmental engineering: environmental health and safety for municipal infrastructure, land use and planning, and industry. New Jersey: Wiley, pp. 177–307, 2009.
46.
YunYMSeoMWKooGH, et al.Pyrolysis characteristics of GFRP (glass fiber reinforced plastic) under non-isothermal conditions. Fuel2014; 137, 321–327. DOI: 10.1016/j.fuel.2014.08.001
De MarcoILegarretaJALaresgoitiMF, et al.Recycling of the products obtained in the pyrolysis of fibre‐glass polyester SMC. Chem Technol Biotechnol1997; 69(2), 187–192. DOI: 10.1002/(SICI)1097-4660(199706)69:2%3C187::AID-JCTB710%3E3.0.CO;2-T
49.
SokoliHUSimonsenMENielsenRP, et al.Conversion of the matrix in glass fiber reinforced composites into a high heating value oil and other valuable feedstocks. Fuel Process Technol2016; 149, 29–39. DOI: 10.1016/j.fuproc.2016.03.013
50.
CunliffeAMJonesNWilliamsPT. Pyrolysis of composite plastic waste. Environ Technol2003; 3330, 37–41. DOI: 10.1080/09593330309385599
51.
OnwudiliJAMiskolcziNNagyT, et al.Recovery of glass fibre and carbon fibres from reinforced thermosets by batch pyrolysis and investigation of fibre re-using as reinforcement in LDPE matrix. Composites Part B2016; 91, 154–161. DOI: 10.1016/j.compositesb.2016.01.055
52.
KouparitsasCEKartalisCNVarelidisPC, et al.Recycling of the fibrous fraction of reinforced thermoset composites. Polym Compos2002; 23(4), 682–689.
53.
TorresADe MarcoICaballeroBM, et al.Recycling of the solid residue obtained from the pyrolysis of fiberglass polyester sheet molding compound. Adv Polym Technol2009; 28(2), 141–149. DOI: 10.1002/adv.20150
