This study evaluates the effects of freeze/thaw cycles on the mechanical performance and failure mode of resistance-welded carbon fibre/polyphenylene sulphide composite joints. Dry and moisture-saturated joints are subjected to 1000 temperature cycles varying between –40°C and 82°C. A silane coating is applied on the stainless steel mesh heating element to improve its adhesion with the polyphenylene sulphide polymer. Results show the limited impact that freeze/thaw cycles have on the lap shear strength of joints welded without any coating on the heating element. The silane coating improves the lap shear strength by 32% when no freeze/thaw cycles are applied to the joints. This improvement of 32% reduces when joints are subjected to freeze/thaw cycles but the mechanical performance remains superior to that of joints welded using uncoated heating element. Fracture surfaces show that fibre/matrix and stainless steel/matrix interfaces are both affected by the environmental conditions although it does not translate into lower lap shear strength.
Airbus. Getting to grips with aircraft performance. Flight Oper Support Line Assist. 2002, p. 11.
2.
AriciAA.Effect of hygrothermal aging on polyetherimide composites. J Reinf Plast Compos2007;
26: 1937–1942.
3.
ShiJWZhuHWuG, et al.
Tensile behavior of FRP and hybrid FRP sheets in freeze-thaw cycling environments. Compos Part B Eng2014;
60: 239–247.
4.
LiHXianGLinQ, et al.
Freeze-thaw resistance of unidirectional-fiber-reinforced epoxy composites. J Appl Polym Sci2012;
123: 3781–3788.
5.
AgarwalAFosterSJHamedE, et al.Influence of freeze–thaw cycling on the bond strength of steel–FRP lap joints.Compos Part B Eng2014;
60: 178–185.
6.
YangYSilvaMAGBiscaiaH, et al.
Bond durability of CFRP laminates-to-steel joints subjected to freeze-thaw. Compos Struct2019;
212: 243–258.
7.
McConnellBKPethrickRA.A dielectric study of hydrolytic ageing and the effects of periodic freezing in carbon fibre reinforced plastic jointed structures. Int J Adhes Adhes2010;
30: 214–224.
8.
HuPShiZWWangXX, et al.
Strength degradation of adhesively bonded single-lap joints in a cyclic-temperature environment using a cohesive zone model. J Adhes2015;
91: 587–603.
9.
Lopez-AnidoRMichaelAPSandfordTC.Freeze-thaw resistance of fiber-reinforced polymer composites adhesive bonds with underwater curing epoxy. J Mater Civ Eng2004;
16: 283–286.
10.
Batista NL, Iha K and Botelho EC. Evaluation of thermal cycling influence on PEI–carbon fiber composites. In: International Conference on Composite Materials (ICCM-19), Montreal, Canada, 28 July 2 August 2013, pp. 8318–8326.
11.
CaoJChenL.Effect of thermal cycling on carbon fiber-reinforced PPS composites. Polym Compos2005;
26: 713–716.
12.
SiscaLMessanaAAiraleAG, et al.
Correlation between thermo-mechanical properties and chemical composition of aged thermoplastic and thermosetting fiber reinforced plastic materials. Materwiss Werksttech2017;
48: 447–455.
13.
YilmazTSinmazçelikT.Effects of thermal cycling on static bearing strength of pin-connected carbon/PPS composites. Polym Compos2010;
31: 328–333.
14.
SınmazçelikTÇobanOBoraMÖ, et al.
The effects of thermal cycles on the impact fatigue properties of thermoplastic matrix composites. Appl Compos Mater2008;
15: 99–113.
VillegasIFMoserLYousefpourA, et al.
Process and performance evaluation of ultrasonic, induction and resistance welding of advanced thermoplastic composites. J Thermoplast Compos Mater2012;
26: 1007–1024.
17.
StavrovDBerseeH.Resistance welding of thermoplastic composites-an overview. Compos Part A Appl Sci Manuf2005;
36: 39–54.
18.
DubéMHubertPYousefpourA, et al.
Resistance welding of thermoplastic composites skin/stringer joints. Compos Part A Appl Sci Manuf2007;
38: 2541–2552.
19.
DubéMHubertPGalletJ, et al.
Fatigue performance characterisation of resistance-welded thermoplastic composites. Compos Sci Technol2008;
68: 1759–1765.
20.
De SouzaSDBAbrahãoACostaML, et al.
Experimental investigation of processing welding parameters for PPS/carbon fiber laminates for aeronautical applications. Adv Mater Res2016;
1135: 62–74.
21.
RohartVLaberge LebelLDubéM.Improved adhesion between stainless steel heating element and PPS polymer in resistance welding of thermoplastic composites. Compos Part B Eng2020; 107876.
22.
TalbotÉHubertPDubéM, et al.
Optimization of thermoplastic composites resistance welding parameters based on transient heat transfer finite element modeling. J Thermoplast Compos Mater2011;
26: 699–717.
23.
Dow Corning. A guide to silane solutions from Dow Corning.
Midland, MI:
Dow Corning, 2005.
ASTM D1002-05.
Standard test method for apparent shear strength of single-lap-joint adhesively bonded metal specimens by tension loading (metal-to-metal). ASTM Int2005. DOI: 10.1520/D1002-10.
26.
HothornLA.The two-step approach—a significant ANOVA F-test before Dunnett’s comparisons against a control—is not recommended. Commun Stat – Theory Methods2016;
45: 3332–3343.
CasellaGFienbergSOlkinI.Springer texts in statistics. vol. 102. New York, NY: Springer, 2006.
29.
Hyer M. Stress analysis of fiber-reinforced composite materials. McGraw Hill Int. Editions, 1998, pp. 423–434.
30.
AbedianASzyszkowskiW.Influence of the free surface on the thermal stresses in unidirectional composites. Compos Part A Appl Sci Manuf1997;
28: 573–579.
31.
BiernackiKSzyszkowskiWYannacopoulosS.Experimental study of large scale model composite materials under thermal fatigue. Compos Part A Appl Sci Manuf1999;
30: 1027–1034.
32.
SinmazçelikTAriciAA.Thermal cycles effects on interlaminar shear strength (ILSS) and impact behaviour of carbon/PEI composites. J Mater Sci2006;
41: 1233–1241.
33.
Toray. Product DatasheetTorayTC1100, Tokyo, Japan: Toray, 2014.
34.
Specialty Steel Industry of the United States (ed.). A designers’ handbook – design guidelines for the selection and use of stainless steel. Nickel Development institute, 1993, p. 3.
