An experimental investigation of carbon fiber-reinforced plastics cutting with an Nd:YVO4 picosecond pulsed system was presented. One-factor experimental design was used in order to explain the influence of cutting parameters including laser power, hatch distance and cutting speed on the pulsed laser–material interaction. The process parameters were optimized by using central composite design of response surface methodology. The results in kerf width, taper angle, material removal rate, and heat-affected zones were discussed through the micrographs observed with optical microscope. Specimens were cut with three different tools: picosecond pulsed laser, nanosecond pulsed laser, and conventional cutting, and the tensile strength and bending strength tests were conducted. Furthermore, the effect of the heat-affected zones on the static strength was also analyzed.
HerzogDJaeschkePMeierOet al.
Investigations on the thermal effect caused by laser cutting with respect to static strength of CFRP. Int J Mach Tool Manufact2008;
48: 1464–1473.
2.
NegarestaniRLiLSezerHKet al.
Nano-second pulsed DPSS Nd:YAG laser cutting of CFRP composites with mixed reactive and inert gases. Int J Adv Manuf Technol2010;
49: 553–566.
3.
FischerFRomoliLKlingR.Laser-based repair of carbon fiber reinforced plastics. CIRP Ann Manuf Technol2010;
59: 203–206.
4.
HuNSZhangLC.Some observations in grinding unidirectional carbon fibre-reinforced plastics. J Mater Process Technol2004;
152: 333–338.
5.
BhatnagarNRamakrishnanNNaikNKet al.
On the machining of fiber reinforced plastic (FRP) composite laminates. Int J Mach Tool Manufact1995;
35: 701–716.
6.
SrinivasuDSAxinteDA.Mask-less pocket milling of composites by abrasive waterjets: an experimental investigation. J Manuf Sci Eng2014;
136: 041005.
7.
KrishnarajVPrabukarthiARamanathanAet al.
Optimization of machining parameters at high speed drilling of carbon fiber reinforced plastic (CFRP) laminates. Compos B Eng2012;
43: 1791–1799.
8.
RomoliLFischerFKlingR.A study on UV laser drilling of PEEK reinforced with carbon fibers. Opt Lasers Eng2012;
50: 449–457.
9.
CennaAAMathewP.Analysis and prediction of laser cutting parameters of fibre reinforced plastics (FRP) composite materials. Int J Mach Tool Manufact2002;
42: 105–113.
DavimJPBarricasNConceiçãoMet al.
Some experimental studies on CO2, laser cutting quality of polymeric materials. J Mater Process Technol2008;
198: 99–104.
12.
YungKCMeiSMYueTM.A study of the heat-affected zone in the UV YAG laser drilling of GFRP materials. J Mater Process Technol2002;
122: 278–285.
13.
LiZLZhengHYLimGCet al.
Study on UV laser machining quality of carbon fibre reinforced composites. Compos Part A Appl Sci Manuf2010;
41: 1403–1408.
14.
MeijerJDuKGillnerAet al.
Laser Machining by short and ultrashort pulses, state of the art and new opportunities in the age of the photons. CIRP Ann Manuf Technol2002;
51: 531–550.
15.
WolynskiAHerrmannTMuchaPet al.
Laser ablation of CFRP using picosecond laser pulses at different wavelengths from UV to IR. Phys Procedia2011;
12: 292–301.
16.
FingerJWeinandMWortmannD.Ablation and cutting of carbon-fiber reinforced plastics using picosecond pulsed laser radiation with high average power. J Laser Appl2013;
25: 1892–1898.
17.
FreitagCWiedenmannMNegelJPet al.
High-quality processing of CFRP with a 1.1-kW picosecond laser. Appl Phys A2015;
119: 1237–1243.
18.
RiveiroAQuinteroFLusquiñosFet al.
Experimental study on the CO2, laser cutting of carbon fiber reinforced plastic composite. Compos Part A Appl Sci Manuf2012;
43: 1400–1409.
19.
HerzogDSchmidt-LehrMOberlanderMet al.
Laser cutting of carbon fibre reinforced plastics of high thickness. Mater Des2016;
92: 742–749.
20.
GennaSTagliaferriFPapaIet al.
Multi-response optimization of CFRP laser milling process based on response surface methodology. Polym Eng Sci2017;
57: 595–605.
21.
OhkuboTSatoYMatsunagaEIet al.
Thermal effect of laser ablation on the surface of carbon fiber reinforced plastic during laser processing. Appl Phys A2018;
124: 149.
22.
KilliAVossASutterDet al.
1.1 kW average output power from a thin-disk multipass amplifier for ultrashort laser pulses. Opt Lett2013;
38: 5442.
