Development of intimate contact during processing of carbon fiber reinforced Polyamide-6 tapes

Abstract

Contact development between the surfaces of two tapes is considered as a critical step in processing carbon fiber reinforced thermoplastic composites. In this study, the development of intimate contact between carbon fiber reinforced Polyamide-6 (PA-6) tapes is investigated experimentally using consolidation experiments and X-ray computed tomography for quantitative contact characterization. The experimental results indicate that the development of intimate contact occurs in the range of seconds even when temperatures are only slightly above the melting temperature and applied pressures is in the range of 1-4 kPa. Experimental data are compared with the results of the two analytical models proposed by Lee and Springer as well as Yang and Pitchumani. Both models overestimate the time needed to reach full contact for the PA-6 tape. In comparison to previously investigated PEEK materials, PA-6 has a relatively low viscosity and the tapes possess a resin-rich layer near the surface, which seems to influence the contact development process. Besides the assumptions made for viscosity, the sensitivity to input parameters describing the surface topology strongly influence the model results and the accuracy of predictions.

Keywords

Intimate contact consolidation carbon fiber reinforced Polyamide-6 fusion bonding contact development

Get full access to this article

View all access options for this article.

References

Henne F, Ehard S, Kollmannsberger A, et al. Thermoplastic in situ fiber placement for future rocket motor casings manufacturing. In: SAMPE Europe technical conference 14, Tampere, Finland, 10–11 September 2014, pp. 46–53.

Grouve

WJB

Warnet

Rietman

. Optimization of the tape placement process parameters for carbon–PPS composites. Compos Part A: Appl Sci Manuf 2013; 50: 44–53.

Bourban

P-E

Bernet

Zanetto

J-E

. Material phenomena controlling rapid processing of thermoplastic composites. Compos Part A: Appl Sci Manuf 2001; 32: 1045–1057.

De Gennes

. Reptation of a polymer chain in the presence of fixed obstacles. J Chem Phys 1971; 55: 572–572.

Bastien

Gillespie

. A non-isothermal healing model for strength and toughness of fusion bonded joints of amorphous thermoplastics. Polym Eng Sci 1991; 31: 1720–1730.

Ageorges

Hou

. Advances in fusion bonding techniques for joining thermoplastic matrix composites: A review. Compos Part A: Appl Sci Manuf 2001; 32: 839–857.

Khan

Mitschang

Schledjewski

. Identification of some optimal parameters to achieve higher laminate quality through tape placement process. Adv Polym Technol 2010; 29: 98–111.

Ageorges

. Fusion bonding of polymer composites, 1st ed. London: Springer, 2002, pp. 105–114.

Tierney

Gillespie

Jr . Modeling of in situ strength development for the thermoplastic composite tow placement process. J Compos Mater 2006; 40: 1487–1506.

10.

Pitchumani

Gillespie

Lamontia

. Design and optimization of a thermoplastic tow-placement process with in-situ consolidation. J Compos Mater 1997; 31: 244–275.

11.

Sonmez

Akbulut

. Process optimization of tape placement for thermoplastic composites. Compos Part A: Appl Sci Manuf 2007; 38: 2013–2023.

12.

Mantell

Springer

. Manufacturing process models for thermoplastic composites. J Compos Mater 1992; 26: 2348–2377.

13.

Lee

Springer

. A model of the manufacturing process of thermoplastic matrix composites. J Compos Mater 1987; 21: 1017–1055.

14.

Yang

Pitchumani

. A fractal Cantor set based description of interlaminar contact evolution during thermoplastic composites processing. J Mater Sci 2001; 36: 4661–4671.

15.

Dara PH and Loos AC. Thermoplastic matrix composite processing model. Technical Report 24061, Virginia Polytechnic Institute and State University, USA, 1985.

16.

Levy

Heider

Tierney

. Inter-layer thermal contact resistance evolution with the degree of intimate contact in the processing of thermoplastic composite laminates. J Compos Mater 2014; 48: 491–503.

17.

Elson

Bennett

. Calculation of the power spectral density from surface profile data. Appl Opt 1995; 34: 201–208.

18.

Welch

. The use of fast Fourier transform for the estimation of power spectra: A method based on time averaging over short, modified periodograms. IEEE Trans Audio Electroacoust 1967; 15: 70–73.

19.

Khanna

Kuhn

. Measurement of crystalline index in nylons by DSC: Complexities and recommendations. J Polym Sci Part B: Polym Phys 1997; 35: 2219–2231.

20.

Murthy

Kagan

Bray

. Effect of melt temperature and skin-core morphology on the mechanical performance of nylon 6. Polym Eng Sci 2002; 42: 940–950.

21.

Gröschel

Drummer

. The influence of moisture and laminate setup on the de-consolidation behavior of PA6/GF thermoplastic matrix composites. Int Polym Proc 2014; 29: 660–668.

22.

Otsu

. Threshold selection method from gray-level histograms. IEEE Trans Syst Man Cybern 1979; 1: 62–66.

23.

Schaefer PM, Staden M, Zaremba S, et al. Material characterization for determining the consolidation properties of carbon fiber tapes with PA-6 matrix. In: International conference on composite materials 20, Copenhagen, Denmark, 19–24 July 2015, paper no. 5201-1.

24.

Stokes-Griffin

Compston

. Investigation of sub-melt temperature bonding of carbon-fibre/PEEK in an automated laser tape placement process. Compos Part A: Appl Sci Manuf 2016; 84: 17–25.