A thermosetting epoxy polymer was modified by incorporating 9 wt% of a CTBN rubber microparticles. The stress-controlled CA tensile fatigue behavior at stress ratio, R = 0.1 for both the neat and the modified epoxy was investigated. The addition of rubber particles increased the epoxy fatigue life by a factor of about three to four times. The rubber particle cavitation and plastic deformation of the surrounding material was observed to contribute to the enhanced fatigue life of the epoxy polymer. Then, the neat and the rubber-modified epoxy resins were infused into a quasi-isotropic, lay-up E-glass fiber, non-crimp fabric in a RIFT set -up to fabricate GFRP composite panels. Further, the stress-controlled CA tensile fatigue tests at stress ratio, R = 0.1 were performed on both of these GFRP composites. Matrix cracking and stiffness degradation was continuously monitored during the fatigue tests. Similar to bulk epoxy fatigue behavior, the fatigue life of GFRP composites increased by a factor of about three times due to the presence of rubber particles in the epoxy matrix. The suppressed matrix cracking and the reduced crack propagation rates in the rubber-modified matrix contribute towards the enhanced fatigue life of GFRP composites employing a rubber-modified epoxy matrix.
Kinloch, A.J. , Shaw, S.J., Tod , D.A. and Hunston, D.L. (1983). Deformation and Fracture Behavior of a Rubber Toughened Epoxy: Microstructure and Fracture Studies , Polymer, 24(10): 1341-1354.
Arias, M.L., Frontini, P.M. and Williams, R.J.J. ( 2003). Analysis of the Damage Zone Around the Crack Tip for Two Rubber-modified Epoxy Matrices Exhibiting Different Toughenability , Polymer, 44(5): 1537-1546.
4.
Pearson, R.A. and Yee, A.F. (1991). Influence of Particle Size and Particle Size Distribution on Toughening Mechanisms in Rubber Modified Epoxies, Journal of Materials Science, 26(14): 3828-3844.
5.
Azimi, H.R. , Pearson, R.A. and Hertzberg , R.W. ( 1996). Fatigue of Rubber-modified Epoxies: Effect of Particle Size and Volume Fraction , Journal of Materials Science, 31(14): 3777-3789.
6.
Low, I.M. and Mai, Y.W. (1988). Micromechanisms of Crack Extension in Unmodified and Modified Epoxy Resins, Composites Science and Technology, 33(3): 191-212.
7.
Lowe, A., Kwon, A.H. and Mai, Y.W. ( 1996). Fatigue and Fracture Behaviour of Novel Rubber Modified Epoxy Resins, Polymer, 37(4): 565-572.
8.
Imanaka, M. , Motohashi, S., Nishi, K., Nakamura, Y. and Kimoto, M. ( 2009). Crack-growth Behaviour of Epoxy Adhesives Modified with Liquid Rubber and Cross-linked Rubber Particles Under Mode I Loading, International Journal of Adhesion and Adhesives, 29(1): 45-55.
9.
Kinloch, A.J. , Masania, K., Taylor , A.C., Sprenger, S. and Egan, D. (2008). The Fracture of Glass Fiber Reinforced Epoxy Composites Using Nanoparticle Modified Matrices, Journal of Materials Science, 43(3): 1151-1154.
10.
Higashino, M. , Takemura, K. and Fujii, T.J. (1995). Strength and Damage Accumulation of Carbon Fabric Composites with a Cross-Linked NBR Modified Epoxy Under Static and Cyclic Loadings, Composite Structures , 32(1-4): 357-366.
11.
Caccavale, V., Wichmann, M.H.G., Quaresimin, M. and Schulte, K. ( 2007). Nanoparticle/Rubber Modified Epoxy Matrix Systems: Mechanical Performance in CFRPs, In: AIAS XXXVI Convegno Nazionale , Ischia, Napoli, 4-8 September.
12.
Manjunatha, C.M., Taylor, A.C., Kinloch, A.J. and Sprenger, S. (2009). The Effect of Rubber Micro-Particles and Silica Nano-Particles on the Tensile Fatigue Behaviour of a Glass Fiber Epoxy Composite, Journal of Materials Science , 44(1): 342-345.
13.
Zhou, Y., Pervin, F., Jeelani, S. and Mallick, P.K. ( 2008). Improvement in Mechanical Properties of Carbon Fabric-Epoxy Composite Using Carbon Nanofibers, Journal of Materials Processing Technology, 198(1-3): 445-453.
14.
Gojny, F.H. , Wichmann, M.H.G., Fiedler, B., Bauhofer, W. and Schulte, K. (2005). Influence of Nanomodification on the Mechanical and Electrical Properties of Conventional Fiber-reinforced Composites, Composites Part A, 36: 1525-1535.
15.
Zhou, Y., Rangari, V., Mahfuz, H., Jeelani, S. and Mallik, P.K. ( 2005). Experimental Study on Thermal and Mechanical Behaviour of Polypropylene, Talc/polypropylene and Polypropylene/Clay Nanocomposites , Materials Science and Engineering A, 402(1-2): 109-117.
16.
Kinloch, A.J. , Mohammed, R.D., Taylor, A.C., Eger, C., Sprenger, S. and Egan, D. (2005). The Effect of Silica Nano Particles and Rubber Particles on the Toughness of Multiphase Thermosetting Epoxy Polymers, Journal of Materials Science, 40(18): 5083-5086.
17.
Kinloch, A.J. , Mohammed, R.D., Taylor, A.C., Sprenger, S. and Egan, D.J. (2006). The Interlaminar Toughness of Carbon Fiber Reinforced Plastic Composites Using Hybrid Toughened Matrices , Journal of materials Science , 41(15): 5043-5046.
18.
Summerscales, J. and Searle, T.J. (2005). Low-Pressure (Vacuum Infusion) Techniques for Moulding Large Composite Structures, Journal of Materials: Design and Application, 219: 45-58.
19.
Johnsen, B.B. , Kinloch, A.J., Mohammed, R.D., Taylor, A.C. and Sprenger, S. (2007). Toughening Mechanisms of Nanoparticle-modified Epoxy Polymers, Polymer, 48(2): 530-541.
20.
American Society for Testing and Materials (2003). Standard Test Method for Tensile Properties of Plastics, ASTM D638-01, Annual Book of ASTM Standards, Vol 8.02 , American Society for Testing and Materials, PA.
21.
American Society for Testing and Materials (2003). Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, ASTM D3039, Annual Book of ASTM Standards, Vol. 15.03, American Society for Testing and Materials , PA.
22.
Garg, A.C. and Mai, Y.W. ( 1988). Failure Mechanisms in Toughened Epoxy Resins - A Review , Composites Science and Technology, 31(3): 179-223.
23.
American Society for Testing and Materials (2003). Standard Test Method for Tension-Tension Fatigue of Polymer Matrix Composite Materials, ASTM D3479M-96, Annual Book of ASTM Standards, Vol. 8.02, American Society for Testing and Materials, PA.
24.
Mandell, J.F. and Meier, U. (1983). Effect of Stress Ratio, Frequency and Loading Time on the Tensile Fatigue of Glass-reinforced Epoxy , In: O’Brien, T. K. (ed.), Long-term Behaviour of Composites, ASTM STP813, pp. 55-77, ASTM International, West Conshohocken, PA.
25.
Staff, C.R. (1983). Effect of Load Frequency and Lay-Up on Fatigue Life of Composites, In: O’Brien, T. K. (ed.), Long-term Behaviour of Composites , ASTM STP813, pp. 78-91, ASTM International, West Conshohocken, PA.
26.
Sun, C.T. and Chan, W.S. (1979). Frequency Effect on the Fatigue Life of a Laminated Composite, In: Tsai, S. W. (ed.), Composite Materials: Testing and Design (Fifth Conference), ASTM STP674, pp. 418-430, ASTM International, West Conshohocken, PA.
27.
Gagel, A., Lange, D. and Schulte, K. ( 2006). On the Relation between Crack Densities, Stiffness Degradation, and Surface Temperature Distribution of Tensile Fatigue Loaded Glass-Fiber Non-Crimp-Fabric Reinforced Epoxy, Composites Part A: Applied Science and Manufacturing, 37(2): 222-228.
28.
Buch, A. ( 1988). Fatigue Strength Calculation, Transtech Publications, Switzerland.
29.
Sauer, J.A. and Richardson, G.C. ( 1980). Fatigue of Polymers , International Journal of Fracture, 16(6): 499-532.
30.
Talreja, R. ( 1981). Fatigue of Composite Materials: Damage Mechanisms and Fatigue Life Diagrams, Proceedings of Royal Society of London A, 378: 461-475.
31.
Hahn, H.T. and Kim, R.Y. ( 1976). Fatigue Behaviour of Composite Laminates, Journal of Composite Materials, 10: 156-180.
32.
Case, S.W. and Reifsnider, K.L. ( 2003). Fatigue of Composite Materials, In: Milne, I., Ritchie, R. O. and Karihaloo, B. (eds), Comprehensive Structural Integrity, Vol. 4: Cyclic Loading and Fatigue , 1stedn, Elsevier Science , Amsterdam.
33.
Tate, J.S. and Kelkar, A.D. ( 2008). Stiffness Degradation Model for Biaxial Braided Composites under Fatigue Loading, Composites Part B: Engineering , 39(3): 548-555.
34.
Lee, J. , Fu, K.E. and Yang, J.N. ( 1996). Prediction of Fatigue Damage and Life for Composite Laminates Under Service Loading Spectra, Composites Science and Technology , 56(6): 635-648.
35.
Reifsnider, K.L. and Jamison , R. (1982). Fracture of Fatigue-loaded Composite Laminate, International Journal of Fatigue, 4(4): 187-192.
36.
Case, S.W., Caliskan, A., Iyengar, N. and Reifsnider, K.L. ( 1996). Performance simulation of High-Temperature Polymericcomposite Materials using MRLife, In: Proceedings of the ASME Aerospace Division-1996 ASME International Mechanical Engineering Congress and Exposition, pp. 375-380.
37.
Reifsnider, K. (1980). Fatigue Behaviour of Composite Materials, International Journal of Fracture, 16(6): 563-583.
