Sage Journals: Discover world-class research

Abstract

An instrumented Izod test was used to investigate the effects of fiber content, coupling agent, and temperature on the impact performance of kenaf fiber reinforced polypropylene (PP). Composites containing 0—60% (by weight) kenaf fiber and 0 or 2% maleated polypropylene (MAPP) and PP/wood flour composites were tested at room temperature and between -50^°C and +50^°C. At room temperature, kenaf greatly reduced energy to maximum load (EML) in reversed notch tests but had little effect in notched tests. MAPP improved all test values. At —25^°C, PP specimens changed from ductile to brittle. Kenaf composites containing MAPP consistently yielded higher EML values than did both unfilled PP specimens and wood flour composites in notched impact tests, over the temperature range investigated. The EML values for kenaf composites were about half those for unfilled PP specimens in reversed notch tests at room temperature, but performance was similar at low temperatures.

Keywords

impact polypropylene kenaf natural fibers.

Get full access to this article

View all access options for this article.

References

Sanadi, A.R. , Rowell, R.M. and Caulfield , D.F. (1994). Reinforcing Polypropylene with Natural Fibers, Plastics Eng. , 50(4): 27—28.

Sanadi, A.R. , Caulfield, D.F. , Jacobson, R. and Rowell, R.M. (1995). Mechanical Properties of Kenaf Fiber-Polypropylene Composites , Indust. Eng. Chem. Res., 34(5): 1891—1896.

Sanadi, A.R. , Caulfield, D.F. and Jacobson, R.E. (1996). Agro-Fiber Thermoplastic Composites, In: Paper and Composites From Agro-Based Resources, Rowell, R. , Young, R. A. and Rowell, J. K. (Eds), CRC Press Inc., Boca Raton, Florida, pp. 377—401.

Kim, J.-K. and Mai,Y.-W. (1991). High Strength, High Fracture Toughness Fibre Composites With Interface Control. A Review, Comp. Sci. Technol., 41(4): 333—378.

Lauke, B. , Schultrich, B. and Pompe, W. (1990). Theoretical Considerations of Toughness of Short-Fiber Reinforced Thermoplastics, Polymer—Plastics Technol. Engrg., 29(7—8): 607—806.

Karger Kocsis, J. (1995). Microstructural Aspects of Fracture in Polypropylene and in Filled, Chopped Fiber and Fiber Mat Reinforced Composites, In: Polypropylene-Structure, Blends, and Composites, Karger Kocsis, J. (Ed.), Chapman and Hall , New York, Vol. 3, pp. 142—201.

English, B. , Clemons, C.M. , Stark, N. and Schneider, J.P. (1996). Waste-Wood-Derived Fillers for Plastics. Gen.Tech. Rep. FPL-GTR-91, U.S. Department of Agriculture, Forest Service, Forest Products Laboratory, Madison, WI.

Park, B.D. (1993). Effects of Impact Modifiers on the Mechanical Properties of Wood—Fibre Polypropylene Composites, M.S. Thesis, Department of Forestry, University of Toronto.

Astm. (2002). ASTM D256—02, Standard Test Method for Impact Resistance of Plastics and Electrical Insulating Materials, Annual Book of ASTM Standards, American Society for Testing and Materials, Philadelphia, PA.

10.

Felix, J.M. and Gatenholm, P. (1991). The Nature of Adhesion in Composites of Modified Cellulose Fibres and Polypropylene, J. Appl. Polym. Sci., 42(3): 602—620.

11.

Raj, R.G. , Kokta, B.V. and Daneault, C. (1989). Effect of Fiber Treatment on Mechanical Properties of Polypropylene-Wood Fiber Composites, Makromol. Chemie, Macromolecular Symposa, 28, 187—202.

12.

Quillin, D.T. (1993). Interface Characteristics and Adhesion in Cellulose/Polypropylene Composites. PhD Thesis, University of Wisconsin, Materials Science Department, Madison, WI.

13.

Sanadi, A.R. and Caulfield, D.F. (2000). Transcrystalline Interphases in Natural Fiber-Polypropylene Composites: Effect of Coupling Agent, Comp. Interfaces, 7(1): 31—43.

14.

Sanadi, A.R. , Young, R.A. , Clemons, C.M. and Rowell, R.M. (1994). Recycled Newspaper Fibers as Reinforcing Fillers in Thermoplastics. Part I. Analysis of Tensile and Impact Properties in Polypropylene, J. Reinf. Plastics Comp., 13(1): 54—67.

15.

Daan, F. , Caulfield, D.F. and Sanadi, A.R. (2001). Effect of Compatibilizer on the Structure-Property Relationships of Kenaf-Fiber/Polypropylene Composites, Polym. Comp., 22(4): 506—517.

16.

McCrum, G. , Read, B.E. and Williams, G. (1967). Anelastic and Dielectric Effects in Polymer Solids , John Wiley, London, pp. 377—387.

17.

Sanadi, A.R. , Caulfield, D.F. , Stark, N.M. and Clemons, C.C. (1999). In: Proceedings, 5th International Conference on Woodfiber-Plastics Conference, Forest Products Society, Madison, Wisconsin, pp. 67—78.

Instrumented Impact Testing of Kenaf Fiber Reinforced Polypropylene Composites: Effects of Temperature and Composition

Abstract

Keywords

Get full access to this article

References