Fluid Impregnation of Deformed Preforms

Abstract

The Resin Transfer Molding (RTM) manufacturing process is frequently used to fabricate parts consisting of doubly curved shells. Woven and stitched bi-directional fabrics deform when draped over tooling surfaces with double curvatures. This deformation results in a corresponding change in the preform's permeability tensor, which will change the fluid impregnation pattern during mold filling stage. This paper presents the results of a study in which flow through deformed preforms was investigated. Experiments were conducted in which two different preforms were radially injected after being sheared to a specified angle. The resulting elliptical flowfronts were used to determine the change in the orientation and degree of anisotropy of the permeability tensor caused by the preform's deformation. The experimental results were then compared with a numerical model developed to describe flow through typical RTM preforms using a deformable unit cell. The anisotropy ratio of the principal permeability tensor was found to increase with the shearing angle as observed experimentally and was verified by the numerical model. The success of the RTM mold design and the accuracy of mold filling simulations are dependent on the use of the correct spatial permeability tensor inside the mold. A predictive model that can provide the permeability changes as a function of local shearing deformation within the draped and compacted preforms should move us closer to a realistic simulation of mold filling in net-shaped composite structures.

Keywords

composites RTM permeability preform architecture deformation

Get full access to this article

View all access options for this article.

References

1. Bickerton, S. , Simacek, P. , Guglielmi, S. , and Advani, S. G. , Investigation of draping and its effects on the mold filling processed during manufacturing of a compound curved composite part. Composites-Part A: Applied Science and Manufacturing, vol. 28A (1997).

2. Dungan, F. D. , Senoguz, M. T. , and Sastry, A. M. , On the use of Darcy permeability in sheared fabrics. Proceedings of the Eighth Japan-U.S. Conference on Composite Materials, pp. 132-144, September 24-25 (1998).

3. Simacek, P. and Advani, S. G. , Permeability model for a woven fabric. Polymer Composites 17(6), pp. 887-899 (1996).

4. Mack, C. , and Taylor, H. M. , The fitting of woven cloth to surfaces. Journal of Textile Institute (1956).

5. Linberg, J. , Behre, B. and Dahlberg, B. , Shearing and buckling of various commercial fabrics. Swedish Institute for Textile Research (1961).

6. Potter, K. D. , The influence of accurate stretch data for reinforcements on the production of complex structural moldings. Composites, pp. 161-167 (1979).

7. Robertson, R. E. , Hsiue, E. S. , Sickafaus, E. S. , and Yeg, G. S. , Fiber rearrangement during the molding of continuous fiber composite I: Flat cloth to a hemisphere. Polymer Composites (1981).

8. Robertson, R. E. , Hsiue, E. S. , and Yeh, G. S. , Continuous fiber rearrangements during the molding of fiber composites II: Flat cloth to a rounded cone. Polymer Composites (1984).

9. Smiley, A. J. , and Pipes, R. B. , Fiber placement during the forming of continuous fiber reinforced thermoplastics. Society of Mechanical Engineers (1987).

10.

10. Van West, B. P. , Pipes, B. R. , Keefe, M. , and Advani, S. G. , The draping and consolidation of commingled fabrics. Composites Manufacturing, March (1995).

11.

11. Laroche, D. , and Vu-Khanh, T. , Forming of woven fabric composites. Journal of Composite Materials, 28(18), pp. 1825-1839 (1994).

12.

12. Horsting, K. , and Wulfhorst, B. , Drapeability of textile reinforced fabrics for composites. 25th International SAMPE Technical Conference, October 26-28 (1993).

13.

13. Trochu, F. , Hammami, A. , and Benoit, Y. , Prediction of fiber orientation and net shape definition of complex composite parts.

14.

14. Van der Ween, F. , Algorithms for draping fabrics on doubly-curved surfaces. International Journal for Numerical Methods in Engineering, vol 31 (1991).

15.

15. Hammani, A. , Trochu, F. , Gauvin, R. , and Wirth, S. , Directional permeability measurement of deformed reinforcement. Proceedings of the International Conference on Composite Materials and Energy, pp. 552-562, May 8-10 (1995).

16.

16. Smith, P. , Rudd, C. D. , and Long, A. C. , The effect of shear deformation on the processing and mechanical properties of aligned reinforcements. Composites Science and Technology, 57, pp. 327-344 (1997).

17.

17. Lai, C-L. and Young, W-B. , Model resin permeation of fiber reinforcements after shear deformation. Polymer Composites, 18(5), pp. 642-648 (1997).

18.

18. Dungan, F. D. , Senoguz, M. T. , Sastry, M. T. , and Faillaci, D. A. , Paper submission for Composites Science and Technology (1988).

19.

19. Fong, L. , and Advani, S. , The role of drapability of fiber preforms in resin transfer molding. Proceedings of the 19th American Societyfor Composites, p. 1246-1246.(1994).

20.

20. Rudd, C. D. , Middleton, M. J. , Long, A. C. , McGeehin, P. , and Bulmer, L. J. , Modelling the processing and performance of preforms for liquid molding processes. Composites Manufacturing, 5(3), pp. 177-186 (1994).

21.

21. Rudd, C. D. , Long, A. C. , McGeehin, P. , and Bulmer, L. J. , Processing and mechanical properties of bi-directional preforms for liquid composite molding. Composites Manufacturing, 6, pp. 211-219 (1995).

22.

22. Rudd, C. D. , Long, A. C. , McGeehin, P. , and Smith P. , In-plane permeability determination for simulation of liquid composite molding of complex shapes. Polymer Composites, 17(1), pp. 52-59 (1996).

23.

23. Long, A. C. , Blanchard, P. J. , Rudd, C. D. and Smith, P. , The development of an integrated process model for liquid composite moulding, Composites Part A: Applied Science and Manufacturing, 29A, pp. 847-854 (1998).

24.

24. Gebart, B. R. , Permeability of unidirectional reinforcements for RTM. Journal of Composite Materials, 26(8), pp. 1100-1133 (1992).

25.

25. Brushke, M. V. , and Advani, S. G., Polymer Composites, 11, p. 398-398.(1990).

26.

26. Image Processing and Analysis, Image version 1.41, by Wayne Rasband, National Institutes of Health, Research Services Branch, NIMH.

27.

27. Advani, S. G. , Brushke, M. V. , and Parnas, R. , Flow Rheology in Polymeric Composites Manufacturing. Chapter 12: Resin Transfer Molding (1994).

28.

28. Chen, B. , and Chou, T. W. , Compaction of woven-fabric preforms in liquid composite molding processes: Nesting and multi-layer deformation. Private communication.

29.

29. Bickerton, S. , Sozer, E. M. , Graham, P. J. , and Advani, S. G. , Fabric structure and mold curvature effects on preform permeability and mold filling in the RTM process, part I: Experiments. Submitted to Composites-Part A: Applied Science and Manufacturing (1998).

30.

30. Bickerton, S. , Sozer, E. M. , Graham, P. J. , and Advani, S. G. , Fabric structure and mold curvature effects on preform permeability and mold filling in the RTM process, part II: Predictions and comparisons with experiments. Submitted to Composites-Part A: Applied Science and Manufacturing(1998).