Development of the Guidance on the Tightening of Large Anchor Rods of Support Structures for Sign and Luminaires

Abstract

Across the United States, various state Departments of Transportation (DOTs) are finding that the base anchor-rod nuts on critical support structures for overhead signs are coming loose. Retightening loose nuts imposes a significant drain on state DOT resources. In addition, the loosening of these nuts increases the failure risk of tall and overhanging structures. In many of the inspection engineer’s observed cases, anchor-rod nuts were loose immediately after installation. Even after tightening, it was found that anchor-rod nuts had consistently come loose just 2 years after retightening. The objective of this study was to evaluate the resistance to the loosening of anchor-rod tightening procedures proposed by Chen et al. and to develop improvements to the procedures based on stakeholder feedback. To achieve this objective, field deployment of the previously developed procedures was conducted on multiple sites. After field deployment, improvements to the Chen et al. procedure were investigated on a full-size laboratory specimen to ensure revisions did not affect connection performance. Overall, it was found that the pretension levels proposed by Chen et al. were effective, and the revised procedures only use torque, or force-controlled tightening, as opposed to displacement-controlled turn-of-nut.

Keywords

large anchor rod anchor rod loosening sign and luminaires structure field monitoring skidmore test

Get full access to this article

View all access options for this article.

References

Culp

J. D.

Witteveen

Wong

H. L.

Action Plan for Cantilever Sign Problem. Report No. RR-712. Michigan Department of Transportation, Lansing, 1990.

James

R. W.

Keating

P. B.

Bolton

R. W.

Benson

F. C.

Bray

D. E.

Abraham

R. C.

Hodge

J. B.

Tightening Procedures for Large-Diameter Anchor Bolts. Texas Transportation Institute, Texas A&M University System, College Station, 1997.

Kaczinski

M. R.

Dexter

R. J.

Van Dien

J. P.

Fatigue-Resistant Design of Cantilevered Signal, Sign, and Light Supports. NCHRP Report 412. National Cooperative Highway Research Program, Washington, D.C., 1998.

Dexter

R. J.

Ricker

M. J.

Fatigue-Resistant Design of Cantilevered Signal, Sign, and Light Supports. NCHRP Report 469. National Cooperative Highway Research Program, Washington, D.C., 2002.

Roy

Park

Y. C.

Sause

Fisher

J. W.

Kaufmann

E. J.

Cost-Effective Connection Details for Highway Sign, Luminaire, and Traffic Signal Structures. Report No. NCHRP Project 10-70. Transportation Research Board, Washington, D.C., 2011.

Garlich

M. J.

Thorkildsen

E. T.

Guidelines for the Installation, Inspection, Maintenance and Repair of Structural Supports for Highway Signs, Luminaires, and Traffic Signals. Report No. FHWA-NHI-05-036. Federal Highway Administration, Office of Bridge Technology, Washington, D.C., 2005.

Till

R. D.

Lefke

N. A.

The Relationship Between Torque, Tension, and Nut Rotation of Large Diameter Anchor Bolts. Michigan Department of Transportation, Materials and Technology Division, Research and Technology Setion, Lansing, 1994.

Johns

K. W.

Dexter

R. J.

Fatigue Related Wind Loads on Highway Support Structures. Advanced Technology for Large Structural Systems Engineering Research Center, Lehigh University, Bethlehem, PA, 1998.

RCSC. Specification for Structural Joints Using High-Strength Bolts. Research Council on Structural Connections, Chicago, IL, 2015.

10.

Fisher

J. W.

Struik

J. H. A.

Guide to Design Criteria for Bolted and Riveted Joints. John Wiley and Sons, New York, NY, 1974.

11.

Bickford

An Introduction to the Design and Behavior of Bolted Joints, 3rd ed. Marcel Dekker, New York, NY, 1995.

12.

CEN. EN 1090-2: Technical Requirements for the Execution of Steel Structures. European Committee for Standardization, Brussels, Belgium, 2018.

13.

Hoisington

Hamel

Investigation of Anchor Nut Loosening in High-Mast Light Poles Using Field Monitoring and Finite Element Analysis. Pacific Northwest Transportation Consortium, University of Washington, Seattle, 2014.

14.

Liu

Dietrich

Phares

B. M.

Shafei

Structural Behavior of Large Anchor Bolts Used for Sign-Support Structures. Journal of Constructional Steel Research, Vol. 190, 2022, p. 107144.

15.

Dietrich

Phares

B. M.

Liu

Re-Tightening the Large Anchor Bolts of Support Structures for Signs and Luminaires: Phase II. Report No. MN 2021-23. Minnesota. Department of Transportation. Office of Research & Innovation, St. Paul, 2021.

16.

Rodriguez Lopez

Atadero

Riveros

Senior

Multi-Axial Fatigue Strength of Structural Bolts in Slip-Critical Connections Under Combined Cyclic Axial and Shear Demands. MS thesis. Civil and Environmental Engineering, Colorado State University, Fort Collins, 2018.

17.

Jiang

Zhang

Lee

C.-H.

A Study of Early Stage Self-Loosening of Bolted Joints. Journal of Mechanical Design, Vol. 125, No. 3, 2003, pp. 518–526.

18.

Junker

G. H.

New Criteria for Self-Loosening of Fasteners Under Vibration. Society of Automotive Engineers, New York, NY, 1969.

19.

DIN. DIN 25201: Design Guide for Railway Vehicles and Their Components - Bolted Joints - Part 1: Classification of Bolted Joints. Deutsches Institut für Normung, Berlin, Germany, 2015.

20.

Yang

Dewolf

J. T.

Mathematical Model for Relaxation in High-Strength Bolted Connections. Journal of Structural Engineering, Vol. 125, No. 8, 1999, pp. 803–809.

21.

Nijgh

M. P.

Loss of Preload in Pretensioned Bolts. Minor thesis. Delft University of Technology, Netherlands, 2016.

22.

Munse

W. H.

Structural Behavior of Hot Galvinized Bolted Connections. Proc., 8th International Confrence on Hot Dip Galvinizing, London, Industrial Newspapers Limited, London, 1967, pp. 223–239.

23.

Van Dien

J. P.

Fatigue Resistant Design of Cantilevered Sign, Signal, and Luminaire Support Structures. Lehigh University, Bethlehem, PA, 1995.

24.

Chen

Schaeffer

Zhang

Phares

Shafi

Yang

Lin

Paudel

Re-Tightening the Large Anchor Bolts of Support Structures for Signs and Luminaires. Minnesota Department of Transportation, St. Paul, 2018.

25.

MnDOT. MnDOT Anchor Rod Tightening Handbook. Minnesota Department of Transportation, Minneapolis, 2020.

26.

MnDOT. MnDOT Standard Plan Transmittal No. 19-01. Design Drawing. Minnesota Department of Transportation, Minneapolis, 2019.

27.

AASHTO. LRFD Specifications for Structural Supports for Highway Signs, Luminaires, and Traffic Signals, 1st ed. American Association of State Highway and Transportation Officials, Washington, D.C., 2015.

28.

LTS-1. LRFD Specifications for Structural Supports for Highway Signs, Luminaires, and Traffic Signals, 1st ed. American Association of State Highway and Transportation Officials, Washington, D.C., 2015.