Experimental verification of predicted capability of a wind turbine drivetrain test bench to replicate dynamic loads onto multi-megawatt nacelles

Abstract

A total of 27 test profiles from the IEC 61400-1 design load cases were tested using a 7.5-MW wind turbine drivetrain test bench and two multi-megawatt wind turbine drivetrains. Each test profile consisted of simultaneous vertical, lateral, and longitudinal forces, yawing and nodding bending moment, and rotational speed. These test-bench inputs were compared with the forces, bending moments, and speed that were applied to the wind turbine drivetrains to quantify the test-bench tracking error. This tracking error was quantified for a range of ramp-rate limits of the yawing and nodding bending moments. The experimental results were compared with predictions from an evaluation method for the capability of wind turbine drivetrain test benches to replicate dynamic loads. The method’s predictive capability was found to be sufficient for the goal of early screening and its formulation is applicable to any wind turbine drivetrain test bench and drivetrain design.

Keywords

Wind turbine drivetrain nacelle test bench test rig dynamic loads

Get full access to this article

View all access options for this article.

References

Aachen University Center for Wind Power Drives (n.d.) 4MW-WT-system test rig for on-shore WEA. Available at: www.cwd.rwth-aachen.de/1/infrastructure (accessed 10 November 2020).

Averous

Stieneker

Kock

, et al. (2017) Development of a 4 MW full-size wind-turbine test bench. IEEE Journal of Emerging and Selected Topics in Power Electronics 5(2): 600–609.

Duda

Jacobs

Bosse (2016) IEA wind task 35 – Full size ground testing of wind turbine nacelles. In: Poster presented at the wind Europe summit turbine technology, Hamburg, Germany, 27–29 September 2016.

Fraunhofer IWES Dynamic Nacelle Testing Laboratory (2017) Available at: www.iwes.fraunhofer.de/content/dam/windenergie/de/documents/aktuelleDatenblaetter/DB%20DyNaLab_2017_en%20print.pdf (accessed 12 September 2021).

Giguère

(2019) Determining wind turbine drivetrain test bench capability to replicate dynamic loads: Evaluation methods and their evaluation. PhD Dissertation, Clemson University, USA.

Giguère

Wagner

(2021) Acceptance criteria for the tracking error of wind turbine drivetrain test bench when replicating dynamic loads. Wind Engineering. Epub ahead of print 13 May 2021. DOI: 10.1177/0309524x211015271.

IEA (2016) Test Center Capabilities Fact Sheet From IEA Task Force 35 for Ground Based Testing for Wind Turbines and Their Components. IEA.

IEC (2019) Standard 61400-1:2019 (2019) Wind Turbines – Part 1: Design Requirements. IEC.

Lindø Offshore Renewables Center (2017) Nacelle testing. Available at: www.lorc.dk/test-facilities#lindo-nacelle-testing (accessed 12 September 2021).

10.

NaREC (n.d.) Powertrain facilities. Available at: https://ore.catapult.org.uk/what-we-do/testing-validation%e2%80%a8/powertrain-facilities (accessed 12 September 2021).

11.

NREL (n.d.) Dynamometer research facilities. Available at: http://www.nrel.gov/wind/facilities-dynamometer.html (accessed 12 September 2021).

12.

Schkoda

(2015) Static uncertainty analysis of a wind turbine test bench’s load application unit. In: American control conference, Chicago, IL, 1–3 July 2015, pp.3150–3155.

13.

Schkoda

Bibo

Guo

, et al. (2016) Characterizing the influence of abstraction in full-scale wind turbine nacelle testing. In: ASME international design engineering technical conference and computer and information in engineering conference, Charlotte, NC, 21–24 August 2016.

14.

Schkoda

Fox

(2014) Integration of mechanical and electrical hardware for testing full scale wind turbine nacelles. In: Clemson university power systems conference, Clemson, SC, 11–14 March 2014, pp.1–8.