This study compares the microstructure, mechanical properties, and corrosion behavior of CoCrFeNiMn high-entropy alloy (HEA) and 316L stainless steel fabricated by selective laser melting (SLM), with a specific focus on the influence of hot rolling post-treatment. The results showed that as SLM-fabricated HEA exhibited a higher microhardness (198.15 Hv) than the 316L, which was further increased to 228.53 Hv after hot rolling due to grain refinement and increasing dislocation density. However, electrochemical testing in 3.5 wt.% NaCl revealed that unrolled HEA had the poorest corrosion resistance, exhibiting severe pitting. Hot rolling improved the HEA's corrosion resistance by eliminating defects and refining its microstructure. In contrast, 316L stainless steel exhibits the optimal pitting corrosion resistance due to its high content of Cr and Mo elements and uniform structure.
RthCCDejeanTTMohrD. Plasticity and fracture of cast and SLM AlSi10Mg: high-throughput testing and modeling. Addit Manuf2021; 43: 101998.
2.
WangJBZhouXLLiJH, et al.Microstructures and properties of SLM-manufactured Cu-15Ni-8Sn alloy. Addit Manuf2020; 31: 100921.
3.
IrshadHMFarooqAAmmarM, et al.Fabrication effect on SLM and cast Inconel 718 properties for energy conversion. J Mater Res Technol2025; 38: 2453–2465.
4.
IvanovDTravyanovAPetrovskiyP, et al.Evolution of structure and properties of the nickel-based alloy EP718 after the SLM growth and after different types of heat and mechanical treatment. Addit. Manuf2017; 18: 269–275.
5.
ChenLLiYZYuTQ, et al.Effects of ultrasonic shot peening process on the microstructure and mechanical properties of nickel-based superalloys formed by selective laser melting. J Mater Res Technol2025; 335: 118667.
6.
PraveenkumarKVishnuJSamuel SC, et al.High temperature dry sliding wear behaviour of selective laser melted Ti-6Al-4 V alloy surfaces. J Mater Process Technol2024; 329: 118439.
7.
HardesCPohlFRottgerA, et al.Cavitation erosion resistance of 316L austenitic steel processed by selective laser melting (SLM). Addit Manuf2019; 29: 100786.
8.
WangCMJiangZQZhangYF, et al.Precipitate-mediated mechanical-corrosion property trade-offs in TIG-welded al-3.2Cu-1.48Li alloy joint. Corros Sci2025; 256: 113197.
9.
GaoBWPengLQZhaoHJ,et al.Research progress of 316L stainless steel forming process based on selective Laser melting technology. Curr Mater Sci2025; 18: 312–338.
10.
SunZJTanXPTorSB,et al.Selective laser melting of stainless steel 316L with low porosity and high build rates. Mater Des2016; 104: 197–204.
11.
KumarPJayarajRSueyawanshiJ, et al.Fatigue strength of additively manufactured 316L austenitic stainless steel. Acta Mater2020; 199: 225–239.
12.
ZhouCSWuFYTangD, et al.Effect of subcritical-temperature heat treatment on corrosion of SLM SS316L with different process parameters. Corros Sci2023; 218: 111214.
13.
WangDCWuCLZhangS, et al.Wear and corrosion of CoCrFeNiMnTix high entropy alloy coatings by laser cladding. Mater Sci Tech2023; 39: 2811–1823.
14.
NguyenATTranASTrinhTN, et al.Enhancing the mechanical properties of cu crystal substrate by CoCrCuFeNi HEA coating: a molecular dynamics study. Mater. Today Commun2025; 47: 113241.
15.
HanFLiCYPaiZL, et al.Heterostructure-mediated intra-film galvanic corrosion in (CrFeCoNiMn)100−xVx (x = 5, 10, 15, 20) high entropy alloy: a novel strategy for synergistic enhancement of mechanical and corrosion resistance properties. Appl Surf Sci2026; 725: 165773.
16.
NenuwaOBThiercelinLPeltierL, et al.Multi-Scale Study of the Influence of Bonding Temperature on the Diffusion Bonding of Equiatomic CoCrFeMnNi High Entropy Alloy and 316L Stainless Steel, Met. Mater Int2026; 32: 334–352.
17.
QiuYGibsonMAFraserHL,et al.Corrosion characteristics of high entropy alloys. Mater Sci Tech2015; 31: 1235–1243.
18.
PamiesFBGottbergA. Microstructure and mechanical properties of high-energy proton irradiated CrMnFeCoNi alloy and CW-316L. J Nucl Mater2025; 614: 155871.
19.
LiXWangXQDaiXL, et al.Enhanced strength with retained ductility in SLM-processed high-entropy alloys via dislocation regulation in L2₁-BCC co-precipitate. Addit Manuf2025; 109: 104899.
20.
ZhangCLWangYLiangHY, et al.Effect of process parameters on residual stresses in SLM-formed bionic porous titanium alloy structures. Mater Today Commun2024; 39: 108539.
21.
TusherMMHInceA. Comprehensive review of fabrication process parameters influencing defect formation in laser powder bed fused (L-PBF) Al-Si alloys. Mater Des2025; 257: 114374.
22.
WangTZhongFCaoX, et al.Microstructure regulation and synergistic deformation of heterogeneous laminated magnesium alloy during roll bonding. Materialia2025; 42: 102484.
23.
TianNLiYZZhangPH, et al.Differences in microstructures and properties of Al-0.81Mg-0.84Si-0.53Cu hot-rolled sheet and hot-extrusion in T6 temper. J Mater Res Technol2025; 38: 3437–3446.
24.
WangZLiZLZhuX, et al.Correlational research of microstructure characteristics and hydrogen induced cracking in hot-rolled fe-6Mn-0.2C-3Al steels. Corros Sci2024; 228: 111811.
25.
WuSWGaoCHeYT, et al.Development and application of a data-driven and mechanistic hybrid model for predicting the microstructure and property of hot-rolled Ti micro-alloyed steel, mater. Today Commun2025; 48: 113292.
26.
HouJXZhangMMaSG, et al.Strengthening in Al0.25CoCrFeNi HEA by cold rolling, mater. Sci Eng A2017; 707: 593–601.
27.
WangWZhaoWYMuWZ, et al.Effect of hot-rolling process on the microstructure, mechanical and corrosion behaviors of dual-phase co-based entropic alloys. Mater Sci Eng A2024; 918: 147433.
28.
NaseriMPeatskovaSImantalabO, et al.Achieving ultrafine lamellar structure and exceptional electrochemical properties of Fe35Mn27Ni28Co5Cr5 high-entropy alloy through severe cold rolling process, mater. Today Commun2024; 39: 109053.
29.
ShahmirHSaeedpourPMehranpourMS, et al.Low cycle fatigue properties of CoCrFeNiMn high-entropy alloy with heterogeneous microstructure. Mater Sci Eng A2024; 912: 147004.
30.
PatilMAGharaTDasB,et al.Influence of cooling rate on microstructure, dislocation density, and associated hardness of laser direct energy deposited Inconel 718. Surf Coat Technol2025; 495: 131575.
31.
YuanXHYuCZLiRD, et al.Influence of stacking fault energy synergistic non-equilibrium solidification on dislocation substructures and mechanical properties of Ti alloys. J Alloys Compd2025; 1039: 183134.
32.
AzabSAENormanJEGomezL, et al.Dislocation-mediated room-temperature mechanical behavior of multiphase entropy stabilized oxides. Acta Mater2024; 281: 120428.
33.
ZhangLLiXHDingR, et al.Role of martensite hardness in governing tensile behavior and local stress states in ferrite/martensite dual-phase steels. Mater Sci Eng A2025; 943: 148841.
34.
ChenNHuYBSongXW, et al.Mitigating synergistic corrosion of X60 steel under SRB and AC interference: optimal CP potentials. Electrochim. Acta2025; 539: 147041.
35.
DaiJFengHLiHB, et al.Composition design of corrosion resistant Fe40Mn40Co10Cr10 HEA by “dissolution-diffusion-deposition” model. J Alloys Compd2025; 1033: 181238.
36.
WangKXuQPLiYH, et al.Influence of sand particle size on the erosion-corrosion resistance of Ni2FeCrMo0.2 HEA in seawater: particle-surface-electrochemistry interaction. J Mater Res Technol2024; 32: 426–438.
37.
KrishnaSARadhikaNSalehB,et al.Microstructural mechanical and corrosion properties of SS304/HEA surface layer produced by friction stir processing. J Alloys Compd2023; 953: 170153.
38.
ZhangPXuZYaoZP, et al.Wu, high-corrosion-resistant high-entropy alloys (HEAs) coatings with single BCC solid solution structure by laser remelting. Mater. Lett2022; 324: 132728.
39.
FengHLiHBDaiJ, et al.Why CoCrFeMnNi HEA could not passivate in chloride solution? - A novel strategy to significantly improve corrosion resistance of CoCrFeMnNi HEA by N-alloying. Corros Sci2022; 204: 110396.
40.
ZhangYYHuSSWenYY, et al.Electrochemical noise analysis of the hot corrosion of TP347H stainless steel: effect of temperature and coal ash thickness. Electrochim Acta2025; 525: 146105.
41.
WangCMWangJCPuLJ, et al.Microstructure and corrosion performance of CrNi and Monel 400 alloy coatings. Mater Chem Phys2025; 346: 131365.
42.
ZhouDJXiaYMGaoZM, et al.Effect of loading conditions on corrosion fatigue process of FSW AA6061-T6 joint in 3.5% NaCl studied by electrochemical noise. J Mater Res Technol2023; 24: 9808–9823.
43.
GaiXBaiYLiS, et al.In-situmonitoring of the electrochemical corrosion behavior in fluoride environment of cellular structured Ti6Al4V alloy fabricated by electron beam melting. Corros Sci2021; 181: 109258.
44.
ChangYChengHXJinXZ, et al.Effect of Si on the corrosion resistance of AlZrNbTi lightweight refractory high-entropy alloys in acidic environment. Corros Sci2024; 238: 112377.
45.
LiuZZhangLMChenWQ, et al.Effect of chloride ion on the corrosion behavior of SiN stainless steel in concentrated hot nitric acid media. Corros Sci2023; 225: 111604.
