The effects of rapid tempering on the microstructure and mechanical properties of 0.34C ultrafine bainitic steel were studied.
Results
indicate that the carbon atoms in bainitic ferrite gradually segregated to dislocations when tempered at 450°C. Cluster strengthening improved the yield strength of the steel and stabilized the retained austenite. At 650°C, most of the retained austenite was decomposed, and numerous carbides were precipitated. The yield strength of the steel was not reduced, but the plasticity and impact toughness were greatly reduced. The optimum temperature for rapid tempering was 550°C, and its microstructure and mechanical properties gradually changed with the extension of tempering time. The duration of tempering can be determined on the basis of specific requirements.
CaballeroFGBhadeshiaHKDH. Very strong bainite. Curr Opin Solid State Mater Sci2004; 8: 251–257.
2.
ZhangFCYangZN. Development of and perspective on high-performance nanostructured bainitic bearing steel. Engineering2019; 5: 319–328.
3.
LiuCChenYFZhangCS. Enhanced strength and plasticity in a novel 55Si2MnMoV spring steel via austempering. Mater Sci Eng A2021; 825: 141887.
4.
ZhangFCKangJ. Progress in scientific research of interfaces in steel (Ⅱ). Iron Steel2022; 57: 26–41.
5.
DongXXShenYFYinTW, et al.Strengthening a medium-carbon steel to 2800 MPa by tailoring nanosized precipitates and the phase ratio. Mater Sci Eng A2019; 759: 725–735.
6.
KangJZhangFCYangXW. Effect of tempering on the microstructure and mechanical properties of a medium carbon bainitic steel. Mater Sci Eng A2017; 686: 150–159.
7.
AleksandraKAndrzejMZFranciscaGC. Enhancing technological prospect of nanostructured bainitic steels by the control of thermal stability of austenite. Mater Des2021; 211: 110143.
8.
WangKGuiXLBaiBZ,et al.Effect of tempering on the stability of retained austenite in carbide-free bainitic steel. Mater Sci Eng A2022; 850: 143525.
9.
ZorganiMGarcia-MateoCJahaziM. Microstructural evolution during tempering of an ausformed carbide-free low temperature bainitic steel. Mater Des2021; 210: 110082.
10.
WangXBLiuCBQinYM, et al.Effect of tempering temperature on microstructure and mechanical properties of nanostructured bainitic steel. Mater Sci Eng A2022; 832: 142357.
11.
LiangZQWangJJLiHG, et al.Microstructure evolution of V-containing low carbon ultra-fine bainitic steel during medium-temperature tempering and strengthening-toughening mechanism. Mater Sci Eng A2024; 901: 146566.
12.
RevillaCLopezBRodriguez-IbabeJM. Carbide size refinement by controlling the heating rate during induction tempering in a low alloy steel. Mater Des2014; 62: 296–304.
SacklSZuberMClemensH,et al.Induction tempering vs conventional tempering of a heat-treatable steel. Metall Mater Trans A2016; 47: 3694–3702.
15.
EuserVKClarkeAJSpeerJG. Rapid tempering: opportunities and challenges. J Mater Eng Perform2020; 29: 4155–4161.
16.
VahidJSakariPSaeedS. Rapid tempering of a medium-carbon martensitic steel: in-depth exploration of the microstructure – mechanical property evolution. Mater Des2023; 231: 112059.
17.
WangJJLiHGWangQC. Effect of rapid tempering at high temperature on microstructure, mechanical properties and stability of retained austenite of medium carbon ultrafine bainitic steel. J Mater Res Technol2024; 28: 3144–3154.
18.
AmarDKDavidMCMartinMC, et al.Quantitative measurement of deformation-induced martensite in 304 stainless steel by X-ray diffraction. Scripta Mater2004; 50: 1445–1449.
19.
GrajcarASkowronekARadwanskiK. Mechanical behavior and stability of dispersed retained austenite in thermomechanically rolled and isothermally-treated TRIP-aided multiphase steel. Mater Sci Eng A2022; 830: 142300.
20.
SantofimiaMJZhaoLSietsmaJ. Volume change associated to carbon partitioning from martensite to austenite. Mater Sci Forum2012; 706–709: 2290–2295.
21.
CaballeroFGMillerMKClarkeAJ,et al.Examination of carbon partitioning into austenite during tempering of bainite. Scripta Materialia2010; 63: 442–445.
22.
HuangQYaoMTimokhinaI. Tempering eactions and elemental redistribution during tempering of martensitic stainless steels. Metall Mater Trans A2019; 50: 3663–3673.
23.
HunkelMDongJEppJ, et al.Comparative study of the tempering behavior of different martensitic steels by means of in-situ diffractometry and dilatometry. Materials2020; 13: 5058.
24.
Saha PodderABhadeshiaHKDH. Thermal stability of austenite retained in bainitic steels. Mater Sci Eng A2010; 527: 2121–2128.
25.
StahlkrantzAHedstromPSariusN, et al.Effect of tempering on the bainitic microstructure evolution correlated with the hardness in a low-alloy medium-carbon steel. Metall Mater Trans A2020; 51: 6470–6481.
26.
SugimotoKIKobayashiMHashimotoSI. Ductility and strain-induced transformation in a high-strength transformation-induced plasticity-aided dual-phase steel. Metall Trans A1992; 23: 3085–3091.
27.
BhadeshiaHKDH. Anomalies in carbon concentration determinations from nanostructured bainite. Mater Sci Technol2014; 31: 758–763.
28.
ShimokawaTYasuiKNiiyamaT. A mechanism of carbon-cluster strengthening through atomic simulations. Mater Trans2020; 11: 2139–2148.
29.
GaoGHZhangHGuiXL, et al.Enhanced ductility and toughness in an ultrahigh-strength Mn–Si–Cr–C steel: the great potential of ultrafine filmy retained austenite. Acta Materialia2014; 76: 425–433.
30.
ZhaoFYChenPXuBY, et al.Martensite transformation of retained austenite with diverse stability and strain partitioning during tensile deformation of a carbide-free Bainitic steel. Mater Charact2021; 179: 111327.
31.
HeSHHeBBZhuKY, et al.Revealing the role of dislocations on the stability of retained austenite in a tempered bainite. Scripta Mater2019; 168: 23–27.
32.
XiongXCChenBHuangMX, et al.The effect of morphology on the stability of retained austenite in a quenched and partitioned steel. Scripta Mater2013; 68: 321–324.
33.
RyuJHKimDIKimHS, et al.Strain partitioning and mechanical stability of retained austenite. Scripta Mater2010; 63: 297–299.
34.
PeetMJBabuSSMillerMK,et al.Tempering of low-temperature bainite. Metall Mater Trans A2017; 48: 3410–3418.
35.
Ruiz-JimenezVKuntzMSourmailT, et al.Retained austenite destabilization during tempering of low-temperature bainite. Appl Sci2020; 10: 8901.
36.
HasanHSPeetMJBhadeshiaHKDH. Severe tempering of bainite generated at low transformation temperatures. Int J Mater Res2012; 103: 1319–1324.
37.
YangZNLiuCBZhangCY. Microplasticity behavior of multiphase high-strength nanobainitic steel based on a modified law of mixtures. Mater Sci Eng A2021; 825: 141848.
38.
van BohemenSMCMorsdorfL. Predicting the Ms temperature of steels with a thermodynamic based model including the effect of the prior austenite grain size. Acta Materialia2017; 125: 401–415.
39.
SinghSBBhadeshiaHKDH. Estimation of bainite plate-thickness in low-alloy steels. Mater Sci Eng A1998; 245: 72–79.
40.
JenaAKChaturvediMC. On the effect of the volume fraction on martensite on the tensile strength of dual-phase steel. Mater Sci Eng1988; 100: 1–6.
41.
YangDPWangTMiaoZT, et al.Effect of grain size on the intrinsic mechanical stability of austenite in transformation-induced plasticity steels: the competition between martensite transformation and dislocation slip. J Mater Sci Technol2023; 162: 38–43.
