In this study, Al–Li alloys containing TiC + TiB2 particles were successfully prepared by mechanical stirring method. The alloy organisation and nanoparticles were investigated by scanning electron microscopy (SEM) and electron probe microanalyser (EPMA). The number of T1 phases in the alloy matrix after different pre-deformation was investigated by transmission electron microscopy (TEM). The results showed that TiC and TiB2 acted as nucleation plasmas for grains during solidification, promoting non-uniform nucleation and refining the grains in the 0.5 samples, the main recrystallisation mechanism of the alloy during solidification was the particle-stimulated nucleation (PSN) mechanism, and the incorporation of nanoparticles improved the recrystallisation resistance of the alloy, while the yield strength of the alloy firstly increased and then decreased as the amount of pre-deformation increased, and the best tensile properties occurred The yield strength and tensile strength of 0.5 samples after 5% pre-deformation were 580 MPa and 603 MPa, respectively.
ChenXZhaoGXuX,et al.Effects of heat treatment on the microstructure, texture and mechanical property anisotropy of extruded 2196 Al–Cu–Li alloy. J Alloys Compd2021; 862: 158102.
2.
SrivatsanTSLaverniaEJEswara PrasadN,et al.Chapter 10 – quasi-static strength, deformation, and fracture behavior of aluminum–lithium alloys. In: Eswara PrasadNGokhaleAAWanhillRJH (eds) Aluminum–lithium alloys. Akron, Ohio: The University of Akron, Butterworth-Heinemann, 2014, pp.305–339. https://doi.org/10.1016/B978-0-12-401698-9.00010-0
3.
LiSYueXLiQ, et al.Development and applications of aluminum alloys for aerospace industry. J Mater Res Technol 2023; 27: 944–983. https://doi.org/10.1016/j.jmrt.2023.09.274
4.
WangLXiaoYKongC,et al.Mechanical properties and microstructure evolution of an Al–Cu–Li alloy via cross cryorolling. Int J Lightweight Mater Manuf2022; 5: 431–439.
5.
Karbalaei AkbariMBaharvandiHRShirvanimoghaddamK. Tensile and fracture behavior of nano/micro TiB2 particle reinforced casting A356 aluminum alloy composites. Mater Des (1980-2015)2015; 66: 150–161.
6.
LiuKJiangXChenS, et al.Effect of SiC addition on microstructure and properties of Al–Mg alloy fabricated by powder and wire cold metal transfer process. J Mater Res Technol2022; 17: 310–319.
7.
ZhouDQiuFJiangQ. The nano-sized TiC particle reinforced Al–Cu matrix composite with superior tensile ductility. Mater Sci Eng A2015; 622: 189–193.
8.
XuJChenGZhangZ, et al.Effect of Al-3 wt% Al2O3 master alloy fabricated by calcined kaolin on grain refinement and mechanical properties of A356 alloy. J Alloys Compd2021; 862: 158512.
9.
TangJYiYHeH, et al.Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: a study with processing map. J Alloys Compd2023; 934: 167755.
10.
ÜnlüBS. Investigation of tribological and mechanical properties Al2O3–SiC reinforced Al composites manufactured by casting or P/M method. Mater Des2008; 29: 2002–2008.
11.
DongB-XLiQ-YShuS-L, et al.Investigation on the elevated-temperature tribological behaviors and mechanism of Al–Cu–Mg composites reinforced by in-situ size-tunable TiB2-TiC particles. Tribol Int2023; 177: 107943.
12.
ShenYLiXHongT, et al.Effects of TiB2 particles on microstructure and mechanical properties of an in-situ TiB2–Al–Cu–Li matrix composite. Mater Sci Eng A2016; 655: 265–268.
13.
LiLHanZGaoM, et al.Microstructures, mechanical properties, and aging behavior of hybrid-sized TiB2 particulate-reinforced 2219 aluminum matrix composites. Mater Sci Eng A2022; 829: 142180.
14.
DuanSLiuZGuoF, et al.Precipitates evolution during artificial aging and their influence on mechanical properties of a cast Al–Cu–Li alloy. J Mater Res Technol2023; 22: 2502–2517.
15.
DuRGaoQWuS, et al.Influence of TiB2 particles on aging behavior of in-situ TiB2/Al–4.5Cu composites. Mater Sci Eng A2018; 721: 244–250.
16.
LiS-SQiuFYangH-Y, et al.Strengthening of dislocation and precipitation for high strength and toughness casting Al–Zn–Mg–Cu alloy via trace TiB2 + TiC particles. Mater Sci Eng A2022; 857: 144107.
17.
ZhaoBCaiQChengJ, et al.Investigation on recrystallization and precipitation behaviors of Al–4.5Cu–1.5 Mg alloy refined by Ti-supported TiC nanoparticles. J Alloys Compd2019; 800: 392–402.
18.
MaX-DYangH-YDongB-X, et al.Novel method to achieve synergetic strength–ductility improvement of Al–Cu alloy by in situ TiC–TiB2 particles via direct reaction synthesis. Mater Sci Eng A2023; 869: 144810.
19.
HuangKZhangKMarthinsenK,et al.Controlling grain structure and texture in Al–Mn from the competition between precipitation and recrystallization. Acta Mater2017; 141: 360–373.
20.
GengJHongTShenY, et al.Microstructural stability of in-situ TiB2/Al composite during solution treatment. Mater Charact2017; 124: 50–57.
21.
XieZJiangRLiX, et al.Microstructural evolution and mechanical properties of TiB2/2195 composites fabricated by ultrasonic-assisted in-situ casting. Ultrason Sonochem2022; 90: 106203.
22.
DengYBaiJWuX, et al.Investigation on formation mechanism of T1 precipitate in an Al–Cu–Li alloy. J Alloys Compd2017; 723: 661–666.
23.
MaKWenHHuT, et al.Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy. Acta Mater2014; 62: 141–155.
24.
DorinTDeschampsADe GeuserF,et al.Quantification and modelling of the microstructure/strength relationship by tailoring the morphological parameters of the T1 phase in an Al–Cu–Li alloy. Acta Mater2014; 75: 134–146.
25.
WenHToppingTDIsheimD, et al.Strengthening mechanisms in a high-strength bulk nanostructured Cu–Zn–Al alloy processed via cryomilling and spark plasma sintering. Acta Mater2013; 61: 2769–2782.
26.
GengRQiuFZhaoQ-L, et al.Effects of nanosized TiCp on the microstructure evolution and tensile properties of an Al–Mg–Si alloy during cold rolling. Mater Sci Eng A2019; 743: 98–105.
27.
KimCSSohnINezafatiM, et al.Prediction models for the yield strength of particle-reinforced unimodal pure magnesium (Mg) metal matrix nanocomposites (MMNCs). J Mater Sci2013; 48: 4191–4204.
28.
GuptaRChaudhariGPDanielBSS. Strengthening mechanisms in ultrasonically processed aluminium matrix composite with in-situ Al3Ti by salt addition. Compos Part B: Eng2018; 140: 27–34.
MalakiMXuWKasarAK, et al.Advanced metal matrix nanocomposites. Metals2019; 9: 30.
31.
WangHLiYXuG, et al.Effect of nano-TiC/TiB2 particles on the recrystallization and precipitation behavior of AA2055-TiC + TiB2 alloys. Mater Sci Eng A2023; 871: 144927.
