To study the influence of the surface roughness and eutectic silicon segregation on the anodising of diecast Al-Si-Cu alloys, an AlSi11Cu2(Fe) alloy was high-pressure diecast and hard anodised. The microstructure and surface topography of milled and grit-blasted regions were investigated to analyse their effect on the growth of the anodic layer. The surface mechanical properties of the anodised surfaces were also studied. The results showed how high surface roughness and silicon segregation present in the grit-blasted surface hindered the thickening of the oxide layer. After anodising, the milled surface exhibited better mechanical properties than the grit-blasted one. The wear resistance was enhanced by a thicker anodic layer, while the scratch resistance was positively affected by a lower surface roughness.
Fratila-ApachiteiLETerrynHSkeldonP, et al.Influence of substrate microstructure on the growth of anodic oxide layers. Electrochim Acta2004; 49: 1127–1140.
5.
ZhuBZanellaC. Influence of Fe-rich intermetallics and their segregation on anodising properties of Al-Si-Mg rheocast alloys. Surf Coat Technol2021; 422: 127570.
6.
ScamponeGTimelliG. The influence of sealing processes and machining operations on the scratch and wear resistance of anodized AlSi9Cu3(Fe) diecasting alloy. JOM2023. https://doi.org/10.1007/s11837-023-06241-3
7.
RevillaRITerrynHDe GraeveI. Role of Si in the anodizing behavior of aAl-Si alloys: additive manufactured and cast Al-Si10-Mg. J Electrochem Soc2018; 165: C532–C541.
8.
Mora-SanchezHDel OlmoRRamsJ, et al.Hard anodizing and plasma electrolytic oxidation of an additively manufactured Al-Si alloy. Surf Coat Technol2021; 420: 127339.
9.
RungeJM. The metallurgy of anodizing aluminum. 1st ed. New York (NY): Springer, 2018.
10.
ZhuBFedelMAnderssonN-E, et al.Effect of Si content and morphology on corrosion resistance of anodized cast Al-Si alloys. J Electrochem Soc2017; 164: C435–C441.
11.
Fratila-ApachiteiLEDuszczykJKatgermanL. Vickers microhardness of AlSi(Cu) anodic oxide layers formed in H2SO4 at low temperature. Surf Coat Technol2003; 165: 309–315.
12.
ScamponeGTimelliG. Anodizing Al–Si foundry alloys: a critical review. Adv Eng Mater2022; 24: 2101480.
13.
LiNMaoWGengX, et al.Microstructure, segregation and fracture behavior of 6061 aluminum alloy samples formed by semi-solid or traditional high pressure die casting. Mater Today Commun2022; 31: 103418.
14.
OtarawannaSGourlayCMLaukliHI, et al.Microstructure formation in AlSi4MgMn and AlMg5Si2Mn high-pressure die castings. Metall Mater Trans A Phys Metall Mater Sci2009; 40: 1645–1659.
15.
GourlayCMLaukliHIDahleAK. Defect band characteristics in Mg-Al and Al-Si high-pressure die castings. Metall Mater Trans A Phys Metall Mater Sci2007; 38: 1833–1844.
16.
TimelliGFabriziA. The effects of microstructure heterogeneities and casting defects on the mechanical properties of high-pressure die-cast AlSi9Cu3(Fe) alloys. Metall Mater Trans A Phys Metall Mater Sci2014; 45: 5486–5498.
17.
CampbellJ. Complete casting handbook: Metal casting processes, metallurgy, techniques and design. 2nd ed. UK: Butterworth-Heinemann, 2011.
18.
CaliariDTimelliGZabalaB, et al.Microstructural and tribological investigations of diecast and hard anodized AlSiCu alloys. Surf Coat Technol2018; 352: 462–473.
19.
British Standards Institution (BSI). Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties. [place unknown]: BSI; 2020. Standard No. EN 1706:2020.
VandersluisERavindranC. Comparison of measurement methods for secondary dendrite arm spacing. Metallogr Microstruct Anal2017; 6: 89–94.
22.
British Standards Institution (BSI). Metallic and oxide coatings - Measurement of coating thickness - Microscopical method. [place unknown]: BSI; 2004. Standard No. EN ISO 1463:2003.
23.
British Standards Institution (BSI). Paints and varnishes - Scratch test using a spring-loaded pen. [place unknown]: BSI; 2020. Standard No. EN ISO 22557:2020.
24.
TiryakioǧluM. Si particle size and aspect ratio distributions in an Al-7%Si-0.6%Mg alloy during solution treatment. Mater Sci Eng A2008; 473: 1–6.
25.
De MoriATimelliGBertoF, et al.High temperature fatigue of heat treated secondary AlSi7Cu3Mg alloys. Int J Fatigue2020; 138: 105685.
26.
ZhuBSeifeddineSPerssonPOÅ, et al.A study of formation and growth of the anodised surface layer on cast Al-Si alloys based on different analytical techniques. Mater Des2016; 101: 254–262.
27.
Fratila-ApachiteiLETichelaarFDThompsonGE, et al.A transmission electron microscopy study of hard anodic oxide layers on AlSi(Cu) alloys. Electrochim Acta2004; 49: 3169–3177.
28.
LeeSGPatelGRGokhaleAM. Inverse surface macro-segregation in high-pressure die-cast AM60 magnesium alloy and its effects on fatigue behavior. Scr Mater2005; 52: 1063–1068.
29.
StraffeliniG. Friction and wear: Methodologies for design and control. New York (NY): Springer, 2015.
30.
ZhuB. Casting and anodising of Al alloys-Alloy design, manufacturing process and material properties [dissertation]. Jönköping (SE): School of Engineering at Jönköping University, 2019.
31.
ZhuBSeifeddineSJarforsAEW, et al.A study of anodising behaviour of al-si components produced by rheocasting. Solid State Phenom2019; 285 SSP: 39–44.
32.
ScamponeGRussoACarminatiA, et al.The influence of the electrolytic bath on the hard anodizing of diecast Al–Si–Cu alloys. Results Surf Interfaces2022; 9: 100089.
33.
FengB. Effects of surface roughness on scratch resistance and stress-strain fields during scratch tests. AIP Adv2017; 7: 035217.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
