The heterogeneous microstructure and mechanical properties of wire-arc additive manufactured 2219 Al–Cu alloy at several heat inputs (HIs) by adjusting the wire feeding speed were investigated. The partially melted zone (PMZ) was regarded as the weak region, and the weakening mechanism was analysed. Results indicated that the size and volume fraction of equiaxial grain increased with higher HI. The mass fraction of the segregated eutectics increased and the concentration of solid solution Cu in the α-Al matrix decreased. In addition, the morphology and distribution characteristics of eutectics were distinctly different at the inter-layer zone and inner-layer zone. The eutectics at the inter-layer PMZ were coarsened and continuous owing to the Cu solid-state diffusion and liquation.
WilliamsSWMartinaFAddisonAC, et al.Wire + arc additive manufacturing. Mater Sci Technol2016; 32: 641–647.
2.
WuBPanZDingD, et al.Effects of heat accumulation on microstructure and mechanical properties of Ti6Al4V alloy deposited by wire arc additive manufacturing. Addit Manuf2018; 23: 151–160.
3.
DerekarKS. A review of wire arc additive manufacturing and advances in wire arc additive manufacturing of aluminium. Mater Sci Technol2018; 34: 895–916.
4.
HeinzAHaszlerAKeidelC, et al.Recent development in aluminium alloys for aerospace applications. Mater Sci Eng A2000; 280: 102–107.
5.
HeHYiYHuangS, et al.An improved process for grain refinement of large 2219 Al alloy rings and its influence on mechanical properties. J Mater Sci Technol2019; 35: 55–63.
6.
BaiJYFanCLLinSB, et al.Mechanical properties and fracture behaviors of GTA-additive manufactured 2219-Al after an especial heat treatment. J Mater Eng Perform2017; 26: 1808–1816.
7.
ZhouYLinXKangN, et al.Mechanical properties and precipitation behavior of the heat-treated wire + arc additively manufactured 2219 aluminum alloy. Mater Charact2021; 171: 110735.
8.
ZhouYLinXKangN, et al.Influence of travel speed on microstructure and mechanical properties of wire + arc additively manufactured 2219 aluminum alloy. J Mater Sci Technol2020; 37: 143–153.
9.
GuJYangSGaoM, et al.Influence of deposition strategy of structural interface on microstructures and mechanical properties of additively manufactured Al alloy. Addit Manuf2020; 34: 101370.
10.
GuJGaoMYangS, et al.Microstructure, defects, and mechanical properties of wire + arc additively manufactured AlCu4.3–Mg1.5 alloy. Mater Des2020; 186: 108357.
11.
GuJGaoMYangS, et al.Pore formation and evolution in wire + arc additively manufactured 2319 Al alloy. Addit Manuf2019; 30: 100900.
12.
WangZLinXWangL, et al.Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al–Cu alloy. Addit Manuf2021; 47: 102298.
13.
QiZQiBCongB, et al.Microstructure and mechanical properties of wire + arc additively manufactured 2024 aluminum alloy components: As-deposited and post heat-treated. J Manuf Process2019; 40: 27–36.
14.
GuJDingJWilliamsSW, et al.The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys. J Mater Process Technol2016; 230: 26–34.
15.
FangXZhangLChenG, et al.Microstructure evolution of wire-arc additively manufactured 2319 aluminum alloy with interlayer hammering. Mater Sci Eng A2021; 800: 140168.
16.
GuJDingJWilliamsSW, et al.The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al–6.3Cu alloy. Mater Sci Eng A2016; 651: 18–26.
17.
CongBDingJWilliamsS. Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al–6.3% Cu alloy. Int J Adv Manuf Technol2015; 76: 1593–1606.
18.
CongBQiZQiB, et al.A comparative study of additively manufactured thin wall and block structure with Al–6.3%Cu alloy using cold metal transfer process. Appl Sci2017; 7: 275.
19.
WuDLiuDNiuF, et al.Al–Cu alloy fabricated by novel laser-tungsten inert gas hybrid additive manufacturing. Addit Manuf2020; 32: 100954.
20.
MaGWangRLiuD, et al.Laser-arc hybrid additive manufactured AlCu alloy for T-shaped structure: microstructure evaluation and molten pool behavior. J Manuf Process2022; 79: 442–459.
21.
SunRLiLZhuY, et al.Microstructure, residual stress and tensile properties control of wire-arc additive manufactured 2319 aluminum alloy with laser shock peening. J Alloys Compd2018; 747: 255–265.
22.
ZhouYLinXKangN, et al.The heterogeneous band microstructure and mechanical performance in a wire + arc additively manufactured 2219 Al alloy. Addit Manuf2022; 49: 102486.
23.
HuangYZhangFYuanJ, et al.Investigation on surface morphology and microstructure of double-wire + arc additive manufactured aluminum alloys based on spectral analysis. J Manuf Process2022; 84: 639–651.
24.
ChenFYangYChenC, et al.Effect of La2O3 particle size on the microstructure and properties of AlSi alloys deposited via wire arc additive manufacturing. J Manuf Process2021; 68: 523–533.
25.
SchuhCA. Nanoindentation studies of materials. Mater Today2006; 9: 32–40.
26.
OliverWCPharrGM. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J Mater Res1992; 7: 1564–1583.
27.
ChengGChoiKSHuX, et al.Determining individual phase properties in a multi-phase Q&P steel using multi-scale indentation tests. Mater Sci Eng A2016; 652: 384–395.
28.
GaoZLiYShiH, et al.Microstructure characteristics under varying solidification parameters in different zones during CMT arc additive manufacturing process of 2319 aluminum alloy. Vacuum2023; 214: 112177.
29.
LiuYTengFCaoFH, et al.Defective GP-zones and their evolution in an Al–Cu–Mg alloy during high-temperature aging. J Alloys Compd2019; 774: 988–996.
30.
ZhouYLinXKangN, et al.Hot deformation induced microstructural evolution in local-heterogeneous wire + arc additive manufactured 2219 Al alloy. J Alloys Compd2021; 865: 158949.
31.
LiQWuALiY, et al.Influence of temperature cycles on the microstructures and mechanical properties of the partially melted zone in the fusion welded joints of 2219 aluminum alloy. Mater Sci Eng A2015; 623: 38–48.
32.
HuangCKouS. Partially melted zone in aluminum welds: solute segregation and mechanical behavior. Weld J2001; 80: 9–17.
33.
HansenN. Hall–Petch relation and boundary strengthening. Scr Mater2004; 51: 801–806.
34.
LiuSWanDPengD, et al.Effect of heat input on nanomechanical properties of wire-arc additive manufactured Al 4047 alloys. Mater Sci Eng A2022; 860: 144288.
35.
MaTGeJChenY, et al.Observation of in-situ tensile wire-arc additively manufactured 205A aluminum part: 3D pore characteristics and microstructural evolution. Mater Lett2019; 237: 266–269.
36.
BaiJYYangCLLinSB, et al.Mechanical properties of 2219-Al components produced by additive manufacturing with TIG. Int J Adv Manuf Technol2016; 86: 479–485.
37.
HuangCKouS. Partially melted zone in aluminum welds – liquation mechanism and directional solidification. Weld J2000; 79: 113–120.
38.
TellkampVLDallekSLaverniaEJ. Mechanical behavior and microstructure of thermally stable bulk nanostructured Al alloy. Metall Trans A2004; 32: 2535–2543.
39.
LiuDWuDMaG, et al.Effect of post-deposition heat treatment on laser-TIG hybrid additive manufactured Al-Cu alloy. Virtual Phys Prototyp2020; 15: 445–459.
