Temperature and density distribution in an industrial stenter frame based on three-dimensional numerical simulation

Abstract

Drying of textiles in industrial facilities represents an energy-intensive process where a large number of measures for energy and production cost savings can be introduced. Typical measures include the introduction of energy management, waste-heat recovery, process optimization and so on. Drying is a complex process with coupled heat and mass transfer between the heated air and humid textile, where parameters such as the air flow rate, air velocity and its flow regime and textile velocity and water content represent significant influential factors. The distribution of air temperature and density inside the drying section of an industrial stenter frame is analyzed in detail using three-dimensional numerical simulation, where the textile is modeled as a porous medium to analyze moisture diffusion within the textile. Heated air is introduced into a chamber by inlet nozzles and removed by exit nozzles, the distribution of which is based on actual machine configuration. A humid textile is introduced into a section, where temperature and density distribution within the textile are calculated for selected time periods. During the simulation in the Fluent program, models of specific component transport, multiphase air flow, turbulent flow, porosity and evaporation were used. The results represent a valuable data set that provides an in-depth insight into the drying process in the industrial stenter machine.

Keywords

Stenter machine textile drying coupled heat and mass transfer computational fluid dynamics temperature distribution density distribution

Get full access to this article

View all access options for this article.

References

Al Musa FF, Qahtani AH, Qwaidh MM, et al. GHG Emissions Reduction Via Energy Efficiency Optimization. In: Greenhouse Gases – Emission, Measurement and Management. Dhahran-Saudi Arabia, InTech; 2012.

Hasanbeigi

Energy-efficiency improvement opportunities for the textile industry. Berkeley: National Laboratory, 2010.

Pabst

Trocken und thermofixieren von Poliesterartikeln unter wirtschaftlichen Gesichtspunkten. Lenzinger Berichte 1979; 47: 230–239.

Wang

Zhang

Chen

, et al. A numerical model of the open-width coupling drying process for cotton fabrics based on the theory of heat and mass transfer in porous media. Text Res J 2020; 90: 1639–1657.

Wang

Zhang

Chen

, et al. Process analysis and optimization of open-width fabric continuous drying based on numerical simulation. Text Res J 2020; 91: 925–949.

Schmidt

CFD Untersuchung des Auftrags hochviskoser polymerer Systeme in Textilen Verarbeitungsprozessen. PhD Thesis, Universitaet Duisburg, DE, 2009.

Guo N, Finnerman O and Strom H. The effect of turbulent velocity fluctuations on the convective heat transfer to droplets subjected to evaporation and thermolysis. Trondheim, Norway. AIP Publishing, 2016.

Wei Y, Hua J, Ding X, et al. A mathematical model for simulating heat and moisture transfer within porous cotton fabric drying inside the domestic air-vented drum dryer. Text Inst Proc 2017; 108(6): 1074–1084.

Fontana

Donca

Mancusi

, et al. Mathematical modeling and numerical simulation of heat and moisture transfer in a porous textile medium. J Text Inst 2016; 107: 672–682.

10.

Ramic M, Zrno A and Husika A. Energy flow analysis of stenter Artos Babckock by textile producer Prevent Fabrics. In: Proceedings. 16th World Textile Conference AUTEX 2016. Ljubljana (Slovenia), June 8–10, 2016.

11.

Ramic M, Hasecic A and Dzaferovic E. Dependence analysis of parameters from thermo-fixing process based on IBM SPSS Statistical tool. In: Proceedings IEEP Conference, Zlatibor, SRB, June 21–24, 2017.

12.

Ramic M, Hasecic A and Dzaferovic E. Numerical analysis of drying process in stenter frame section. In: 19th ICNAAM conference of numerical analysis and applied mathematics. AIP Conf. Proc. 2293 by AIP Publishing, Rhodes, Greece, September 20–26, 2021.

13.

Wan J, Zhang J, Bergstrom D, et al. Numerical modeling for the underfill flow in flip-chip packaging. IEEE Trans Compon Packag Technol 2009; 32:27–234.

14.

ANSYS Inc., ANSYS Fluent Users Guide. https://ansyshelp.ansys.com (2018, accessed 06 September 2021).