Use of 3D Angle-Interlock Woven Fabric for Seamless Female Body Armor: Part 1: Ballistic Evaluation

Abstract

In contrast to making male body armor, manufacturers of body armor encounter problems in design and manufacture of female body armor because of the curvaceous body shape of females. The traditional cut-and-sew method could be used to form the dome shape to accommodate the bust area but it gives rise to weakness at the seams against projectile impact. Fabric folding has been another way to form the domes but it also leads to reduced impact performance and wearing discomfort. In this paper, angle-interlock woven fabrics are proposed as an alternative to the conventional plain woven fabrics in making female body armor due to their advantages in moldability without the need of cutting or folding and ease in manufacture. However, it is vital that the angle-interlock fabrics satisfy the ballistic requirements before being employed for the body armor application. Part Ι of this paper reports on an investigation on the ballistic performance of angle-interlock fabrics. It has been found that the angle-interlock fabric is not less than the conventional fabric constructions used for body armor against ballistic impact. Based on the employment of the angle-interlock fabric, Part ΙΙ presents the mathematical modeling of molding of angle-interlock fabrics to form the front panel of female body armor, which would lead to quick creation of female body armor based on the input of the body and bust sizes.

Keywords

female body armor angle-interlock ballistic test

Get full access to this article

View all access options for this article.

References

Chen, X. , Lo, W.Y. , Tayyar A.E. , and Day, R.J. , Mouldability of Angle-interlock Woven Fabrics for Technical Applications, Textile Res. J. 72(3), 195-200 ( 2002).

Chen, X. , Knox, R.T. , McKenna D.F. , and Mather, R.R. , Relationship between Layer Linkage and Mechanical Properties of 3D Woven Textile Structures. Proc.VTT-Textiles and Composites 92. Symposium 133, Tampere, Finland. 1992 , pp. 166-172.

Roedel, C. and Chen, X. , Innovation and Analysis of Police Riot Helmets with Continuous Textile Reinforcement for Improved Protection, J. Inf. Comput. Sci., 2(2), 127-136 (2007).

Naik, N.K. , Azad, S.K.N.M. , and Prasad, P.D. , Stress and Failure Analysis of 3D Angle Interlock Woven Composites, Aerospace Engineering Department, Indian Institute of Technology , Powai, Mumbai, 400076, India. 3 Oct ( 2000), p. 95.

Ellison, R. , Investigation into Bullet Resistant Vests for Female Police Officers, A dissertation submitted to the University of Manchester Institute of Science & Technology for the degree of Bachelor of Science with Honours, Department of Textiles, the University of Manchester, 2002, pp. 25, 46.

Sun, B. , Gu, B. , and Ding, X. , Compressive Behaviour Of 3-D Angle-Interlock Woven Fabric Composites at Various Strain Rates, Colleague of Textiles, Donghua University, Zhongyuan Institute of Technology, Zhengzhou, Henan Province, 7 January 2005. Polymer Testing 24, 2005 , pp. 447-454.

Cox, B.N. , Dadkhah, M.S. , Inman, R.V. , Morris W.L. , and Zupon, J. , Mechanisms of Compressive Failure in 3D Composites Acta Metall. Mater., 40(12), 3285-3298 (1992).

Tsai, K.H. , Chiu C.H. , and Wu, T.H. , Fatigue Behavior of 3D Multi-Layer Angle Interlock Woven Composite Plates . Compos. Sci. Technol., 60, 241-248 (2000).

Gu, H. and Zhong, Z. , Tensile Behaviour of 3D Woven Composites by Using Different Fabric Structures . Tianjin Polytechnic University, Tianjin, China, 12 Nov 2002, Elsevier Science , 23(7), Oct 2002, pp. 671-674.

10.

Sun, B. and Gu, B. , Frequency Analysis of Stress Waves in Testing 3-D Angle-interlock Woven Composite at High Strain Rates, Colleague of Textiles, Donghua University, Zhongyuan Institute of Technology, Zhengzhou, Henan Province, China, J. Compos. Mater., 41(24), 2915-2938 (2007).

11.

Tan, P. , Tong L. , and Steven, G.P. , Micromechanics models for mechanical and thermo mechanical properties of 3D through-the-thickness angle interlock woven composites Composites Part A. Applied Science and Manufacturing (1999), 637-648.

12.

Sheng, S. and Hoa, S. , Modelling of 3D Angle-interlock Woven Fabric Composites, Concordia Centre for Composites, Department of Mechanical Engineering Concordia University, 1455 de Maisonneuve Blvd. West H549, Montreal, QC Canada H3G 1M8, J. Thermoplastic Compos. Mater., 16, 45-58 (2003).

13.

Mackerle, J. , Finite element analysis and simulation of manufacturing processes of composites and their mechanical properties: a bibliography (1985-2003), Department of Mechanical Engineering, Linkoping Institute of Technology, Sweden, 18 March 2004, Comput. Mater. Sci., 31, 187-219 ( 2004).

14.

Chen, X. , Spola, M. , Gisbert, P.J. , and Mollst, S.P. , Experimental Studies on the Structure and Mechanical Properties of Multilayer and Angle-interlock Woven Structures. J. Textile Inst. 60(1), 91-99 (1999).

15.

Ashcroft, J. , Daniels, D.J. , and Hart, S.V. , U.S. Department of Justice (Office of Justice Programs, National Institute of Justice) Selection and Application Guide to Personal Body Armor NIJ Guide 100-01 (Update to NIJ Guide 100-98), 2001, p. 37.

16.

Croft, J. , PSDB body armor standards for UK police, Home Office, Police Scientific Development Branch, p. 6.