In this study, the influence of stitch bonding on the tensile strength and tensile modulus in plain woven Twaron T-750/vinyl ester composites in the direction of thickness was examined. The effect of stitch density was investigated in longitudinal (warp) and transverse (weft) directions as a parameter. The space (opening) geometry and the deformation caused by the stitching process around stitch points were investigated. The stitching tension, stitch thread type and diameter were kept constant throughout the study. An increase in the tensile strength was observed for low stitching densities while there was no change in the tensile strength for medium stitching densities. A decrease in the tensile strength was observed for high stitching densities. It is especially noted that the tensile strength, which is on the transversal direction perpendicular to stitch direction, decreased with stitching density and tensile deformations initiated much earlier in this direction. It was understood that fiber deviations and resin rich areas were much more effective on these decreases compared with fiber deformation.
Dransfield, K. , Baillie, C., and Mai, Y.-W., On stitching as a method for improving the delamination resistance of CFRPs, In "Proceedings of Advanced Composites ’93", Chandra, T., and Dhingra, A. K. (eds), International Conference on Advanced Materials, University of Wollongong, Australia, 15- 19 February 1993, pp. 351- 357. Co-sponsored: Minerals and Metals & Materials Society, The Society (Warrendale, Pa).
2.
Dransfield, K., Baillie, C., and Mai, Y.-W., Improving the Delamination Resistance of CFRP by Stitching - A Review, CompositesSci. Technol. , 50, 305-317, (1994).
3.
Ko, F.K., Three-dimensional fabrics for composites, in "Textile Structural Composites", Chou, T. W., and Ko, F.K. (eds), Elsevier, Amsterdam, 1989, pp. 129-169.
4.
Lomov, S.V., Bogdanovich, A.E., Ivanov, D.S., Mungalov, D., Karahan, M., and Verpoest, I., A Comparative Study of Tensile Properties of Non-crimp 3D Orthogonal Weave and Multi-layer Plain Weave E-glass Composites. Part 1: Materials, methods and principal results, Composites A, in press (doi:10.1016/j.compositesa.2009.03.012).
5.
Ivanov, D.S., Lomov, S.V., Bogdanovich, A.E., Karahan, M., and Verpoest, I., A Comparative Study of Tensile Properties of Non-crimp 3D Orthogonal Weave and Multi-layer Plain weave E-glass Composites. Part 2: Comprehensive Experimental Results, Composites A, in press (doi:10.1016/j.compositesa.2009.04.032).
6.
Liu, D., Delamination Resistance in Stitched and Unstitched Composite Plates Subjected to Impact Loading, J. Reinforced Plastics Composites, 1(59) (1991).
7.
Dow, M.B., and Smith, D.L., Damage tolerant composite materials produced by stitching carbon fibres. in "21st International SAMPE Technical Conference", Society for the advancement of Material and Processing, Covina, CA, September 1989, pp. 595-605.
8.
Farley, G.L. , and Dickinson, L., Removal of Surface Loop from Stitched Composite Can Improve Compression and Compression-After-Impact Strengths, J. Reinforced Plastics Composites, 6, 633, (1992).
9.
Guenon, V.A. , Chou, T.-W., and Gillespie , J.W. Jr, Toughness Properties of a Three-Dimensional Carbon-Epoxy Composite, J. Mater. Sci. , 24, 4168, (1989).
10.
Karahan, M. , Ku, A., and Eren, R., An Investigation into Ballistic Performance and Energy Absorbtion Capabilities of Woven Aramid Fabrics, Int. J. Impact Eng., 35(6), 499-510 ( 2008).
11.
Mouritz, A.P. , Bannister, M.K., Falzon, F.J., and Leong, K.H., Review of Applications for Advanced Three-Dimensional FibreTextile Composites, Composites A, 30(12), 1445- 1461 (1999).
12.
Dransfield, K., Baillie, C., and Mai, Y.-W., Improving the Delamination Resistance of CFRP by Stitching - a Review, CompositesSci. Technol. , 50, 305-317, (1994).
13.
Weimer, C., and Mitschang, P., Aspects of the Stitch Process on the Quality of Sewn Multi-textile Preforms , Composites A, 32, 1477-1484 (2001 ).
14.
Mouritz, A.P. , and Jain, L.K., Further Validation of the Jain and Mai Models for Interlaminar Fracture of Stitched Composites, CompositesSci. Technol., 59, 1653-1662 (1999).
15.
Cox, B.N. , Massabò, R., and Kedward, K.T., The Suppression of Delaminations in Curved Structures by Stitching, Composites A, 27, 1133-1138 ( 1996).
16.
Dransfield, K.A., Jain, L.K., and Mai, Y.-W., On the Effects of Stitching in CFRPs - I. Mode I Delamination Toughness, CompositesSci. Technol. , 58, 815-827 (1998).
17.
Jain, L.K., Dransfield, K.A., and Mai, Y.-W., On the Effects of Stitching in CFRPs - II. Mode II Delamination Toughness, CompositesSci. Technol., 58, 829-837 ( 1998).
18.
Pelstring, R.M. , and Madan, R.C., Stitching to improve damage tolerance of composites, in "Proceeding of the 34th International SAMPE Symposium", Society for the advancement of Material and Processing, The Society, Reno, Nevada, USA, 8- 11 May, 1989, pp. 1519-1528.
19.
Dow, M.B. , and Smith, D.L., Damage-tolerant composite materials produced by stitching carbon fabrics, in "Proceedings of the 21st International SAMPE Technical Conference", Society for the advancement of Material and Processing, SAMPLE, 1991, San Diego, CA , USA, 25-28 September, 1989, pp. 595-605.
20.
Velmurugan, R., and Solaimurugan , S., Improvements in Mode-I Interlaminar Fracture Toughness and In-Plane Mechanical Properties of Stitched Glass-Polyester Composites, CompositesSci. Technol., 67, 61-69 (2007).
21.
Mouritz, A.P. , Leong, K.H., and Herszberg , I., A Review of the Effect of Stitching on the In-Plane Mechanical Properties of Fibre Reinforced Polymer Composites, Composites A28, 979-991 (1997).
22.
Mouritz, A.P. , and Cox, B.N., A Mechanistic Approach to the Properties of Stitched Laminates, Composites A, 31(1), 1-27 (2000).
23.
Aymerich, F. , Priolo, P., and Sun, C.T., Static and Fatique Behaviour of Stitched Graphite/Epoxy Composite Laminates, CompositesSci. Technol. , 63, 907-917 (2003).
24.
Kang, T.J., and Lee, S.H., Effect of Stitching on Tthe Mechanical and Impact Properties of Woven Laminate Composite, J. Composite Mater., 28, 1574-1587 ( 1994).
25.
Haris, H., Schinske, N., Krueger, R., and Swanson, B., Multiaxial stitched preform reinforcements for RTM fabrication, in "Proceedings of the 36th International SAMPE Symposium", Society for the advancement of Material and Processing, SAMPLE, Baltimore, MD, USA, April 1991, 521(35), pp. 15-18.
26.
Thuis, H.G.S.J. , and Bron, E., "The Effect of Stitching Density and Laminate Lay-Up on the Mechanical Properties of Stitched Carbon Fabrics", Report NLR CR 96126L, National Lucht-en Ruimtevaartlaboratorium , Amsterdam, 1996.
27.
Herszberg, I. , Weller, T., Leong, K.H., and Bannister , M.K., The residual tensile strength of stitched and unstitched carbon/epoxy laminates impacted under tensile load, in "Proceedings of the 1st Aust Congress on Applied Mechanics", 21-23 February 1996, pp. 309-314.
28.
Beier, U., Fischer, F., Sandler, J.K.V., Atstadt, V., Weimer, C., and Buchs, W., Mechanical Performance of Carbon Fibre Reinforced Composites based on Stitched Preforms, Composites A, 38,1655-1663 (2007 ).
29.
Gunnion, A.J. , Scott, M.L., Thomson, R.S., and Hachenberg , D., Thickness Effects on the Compressive Stiffness and Strength of the Stitched Composite Laminates , Composite Struct., 66, 479-486 (2004).
30.
Hai, W. , Guo-Jun, S., Xi-Wu, X., and Shu-Tian, L., Effects of Stitching Parameters on In-Plane Stiffness and Strength of Composite Laminates, Gongcheng Lixue/Engineering Mechanics, 22(6), 82-86 (2005).
31.
Jain, L.K., and Mai, Y.-W., Recent work on stitching of laminated composites - theoretical analysis and experiments, in "Proceedings of the 11th International Conference of Composite Materials", Scott, M. L. (ed.), Technomic Publishing, Lancaster, PA, 1997, pp. I-25-I-51.
32.
Du, X., Xue, F., and Gu, Z., Experimental study of the effect of stitching on strength of a composite laminate , in "Proceedings of the International Symposium on Comp Mat Struct", 10- 13 June 1986, pp. 912-918.
33.
Karkkainen, R.L. , Tzeng, J.T., and Moy, P., Finite element micromechanical strength modeling of stitched 3d-orthogonal composites, Society for the advancement of Material and Processing, in "Proceedings of SAMPE’07" , Baltimore, MD, June 3-7 2007.
34.
Koissin, V. , Ruopp, A., Lomov, S.V., Verpoest, I., Witzel, V., and Drechsler, K., On Surface Fibre-Free Zones and Irregularity of Piercing Pattern in Structurally Stitched NCF Preforms, Adv. Composites Lett., 15(3), 87-94 ( 2006).
35.
Pang, F., Wang, C.H., and Bathgate, R.G., Creep Response of Woven Fibre Composites and the Effect of Stitching, CompositeSci. Technol., 57, 91-98 (1997).
36.
Bathgate, R.G. , Wang, C.H., and Pang, F., Effects of Temperature on the Creep Behaviour of Woven and Stitched Composites, Composite Struct., 38, 435-445 (1997).
37.
Larsson, F., Damage Tolerance of a Stitched Carbon/Epoxy Laminate, Composites A28, 923-934 (1997).
38.
Shah Khan, M.Z. , and Mouritz, A.P., Fatigue Behaviour of Stitched GRP Laminates , Composite Sci. Technol., 56, 695- 701 ( 1996).
39.
Mouritz, A.P. , Gallagher, J., and Goodwin, A.A., Flexural and Interlaminar Shear Properties of Stitched GRP Laminates Following Repeated Impacts, CompositeSci. Technol., 57, 509-522 (1996).
40.
Vandermey, N.E., Morris, D.H., and Masters, J.E., "Damage Development under Compression-Compression Fatigue Loading in a Stitched Uniwoven Graphite/Epoxy Composite Material", NASA Report PB91-236026, 1991.
41.
Furrow, K.W. , Loos, A.C., and Cano, R.J., Environmental Effects on Stitched RTMTextile Composites, J. Reinforced Plastics Composites, 15, 378-419 ( 1996).
42.
Reeder, J.R. , Stitching vs a Toughened Matrix: Compression Strength Effects, J. Composite Mater., 29, 2464-2487 ( 1995).
43.
Mouritz, A.P. , Flexural Properties of Stitched GRP Laminates , Composites A, 27, 525-530 (1996).
44.
Mikhaluk, D.S. , Truong, T.C., Borovkov, A.I., Lomov, S.V., and Verpoest , I., Experimental Observations and Finite Element Modelling of Damage Initiation and Evolution in Carbon/Epoxy Non-Crimp Fabric Composites, Eng. Fracture Mech., 75(9), 2751-2766 (2008).
45.
Truong, T.C. , Vettori, M., Lomov, S.V., Verpoest, I., Carbon Composites based on Multi-Axial Multi-Ply Stitched Preforms, Part 4, Mechanical Properties of Composites and Damage Observation, Composites A, 36, 1207-1221 (2005 ).
46.
Dransfield, K.A., Baillie, C.A., and Mai, Y.-W., The Mode II delamination fracture Ttoughness of stitched CFRP’s, in "Proceedings of the 2nd Pacific Int. Conf: on Aero. Sci. and Tech./6th Aust. Aero. Conf", 20-23 March 1995, Vol. I, pp. 211-218.
47.
Palmer, R.J., Dow, M.B., and Smith, D.L., Development of stitching reinforcement for transport wing panels, in "Proceedings of the 1st NASA Adv. Comp. Tech. Conf", Part 2, 1991, pp. 621-646.
48.
Vasiliev, V.V. , and Morozov, E.V., "Mechanics and Analysis of Composite Materials ", Elsevier, Oxford, UK, 2001.
49.
Herszberg, I. , and Bannister, M.K., Tensile properties of thin stitched carbon/epoxy composites, in "Proceedings of the 5th Aust. Aero. Conference" 20-23 March 1993, pp. 213-18.
50.
Lomov, S.V. , Belov, E.B., Bischoff, T., Ghosh, S.B., Chi, T.T., and Verpoest , I., Carbon Composites based on Multiaxial Multiply Stitched Preforms. Part 1. Geometry of the Preform , Composites A, 33, 1171-1183 (2002).
