Longitudinal and Transverse Moduli and Strengths of Low Angle 3-D Braided Composites

Abstract

This paper presents the results of an experimental study conducted on a class of three-dimensional braided graphite-epoxy composites as well as the results of a modeling study to relate the microstructural variables such as volume fraction of fibers and braid angles to the anisotropic elastic moduli and strengths of these composites. In the experimental program, composite samples with a range of volume fractions (0.2-0.45) and a range of braid angles (0°-30°) were produced and tested in simple compression in both longitudinal and transverse directions. Such data is currently unavailable in literature on a single material system. Extreme care was taken in processing to minimize porosity and non-homogenieties in microstructure, and in proper strain gaging to ensure the reliability and reproducibility of our measurements. In the modeling study, the measured elastic moduli were compared against the currently employed isotrain and isostress models for these materials. At the present time, it is widely reported in literature that the predictions of isostrain model are fairly accurate. This study revealed that the isostrain model predictions can be in significant error and that a weighted average of the isostrain and isostress model predictions yielded the best comparisons against the experiments. For the strength of the composite in the longitudinal and transverse directions, correlations expressing these properties as a function of volume fraction and braid angle were motivated by micromechanics and experimental observations. The predictive capability of these correlations for the selected class of 3-D braided composites was found to be reasonable.

Keywords

textile composites three dimensional braided composites anisotropic elastic moduli anisotropic yield strength experimental measurements isostrain model isostress model Weighted Average Model (WAM)

Get full access to this article

View all access options for this article.

References

1. Ko, F. K. 1989. "Three Dimensional Fabrics for Composites," Textile Structural Composites, T. W. Chou and F. K. Ko, eds., Amsterdam: Elsevier Science Publishers, pp. 129-171.

2. Ko, F. K. 1987. "Braiding," Engineered Materials Handbook, Volume 1, Composites, ASM International, pp. 519-528.

3. Whyte, D. W. 1986. On the Structure and Properties of 3-D Braided Composites, Ph.D. Thesis, Philadelphia, PA: Drexel University.

4. Pastore, C. M. 1988. A Processing Science Model of Three Dimensional Braiding, Ph.D. Thesis, Philadelphia, PA: Drexel University.

5. Naik, R. J. , P. G. Ieju and J. E. Masters . 1994. J. Comp. Matls., 28:656-681.

6. Masters, J. E. , R. L. Foye , C. M. Pastore and Y. A. Gowayed . 1993. J. Comp. Tech. Res., 15:112-122.

7. Pastore, C. M. and Y. A. Gowayed . 1994. J. Comp. Tech. Res., 16:32-36.

8. Jones, R. M. 1975. "Mechanics of Composite Materials," New York: Hemisphere Publishing Corporation.

9. Kregers, A. F. and G. A. Teters . 1979. Mech. Comp. Matls., 4:377-383.

10.

10. Nahas, M. N. 1986. J. Comp. Tech. Res., 8:138-153.

11.

11. Labossiere, P. and K. W. Neale . 1987. Solid Mech. Arch., 12:65-95.

12.

12. Sun, C. T. and B. J. Quinn . 1994. Proceedings of the American Society for Composites, Ninth Technical Conference, Technomic Publishing Co., Inc.

13.

13. Ko, F. K. , D. Whyte and C. Pastore . 1986. Fundamental Studies of 3-D Braid Reinforced Metal Matrix Composites, Part 1: A Processing Science Base and Fabric Geometry Model, Final Report. Submitted to Department of the Navy Office of Naval Research.

14.

14. Wang, Y. and A. S. D. Wang . 1995. "Microstructure Property Relationships in 3-Dimensionally Braided Fiber Composites," Composites Science and Technology, V53:213-222.

15.

15. Franco, E. J. 1995. "Finite Element Simulation of the Micromechanical Behavior of Three-Dimensionally Braided Composite Materials," M.S. Thesis, Drexel University.

16.

16. Abusafieh, A. 1996. "Development and Micromechanics of a New Class of Swelling-Type Composite Materials for Bioimplant Applications," Ph.D. Thesis, Drexel University.

17.

17. Chamis, C. C. 1989. "Mechanics of Composite Materials: Past, Present, and Future," Journal of Composites Technology & Research, JCTRER, 11(1):3-14.