The focus of this paper is the development of test procedures to characterize the damage-related behavior of a unidirectional composite at room temperature and quasi-static loading conditions and use the resulting data in the damage sub-model of a newly developed material model for orthotropic composites. This material model has three distinct sub-models to handle elastic and inelastic deformations, damage, and failure. A unidirectional composite—T800/F3900 that was the focus of our previous work, is used to illustrate how the deformation and damage-related experimental procedures are developed and used. The implementation of the damage sub-model into LS-DYNA is verified using single-element tests and validated using impact tests. Results show that the implementation yields reasonably accurate predictions of impact behavior involving deformation and damage in structural composites.
OliginSLBronstedPZangenbergJ. Composite materials: constituents, architecture, and generic damage. Modeling Damage Fatigue Failure Compos Mater, ▪▪, 2016, pp. 3–23.
2.
ChoiHYDownsRJChangFK. A new approach toward understanding damage mechanisms and mechanics of laminated composites due to low-velocity impact: part I-experiments. J Compos Mater1991; 25: 992–1011.
3.
UyanerMKaraM. Dynamic response of laminated composites subjected to low-velocity impact. J Compos Mater2007; 41: 2877–2896.
4.
MastersJE. Characterization of impact damage development in graphite/epoxy laminates. Fractogr Modern Eng Mater Compos Metals, ASTM STP 948, ▪▪, 1987, pp. 238–258.
5.
YashiroSKeijiONakamureTet al.Characterization of high-velocity impact damage in CFRP laminates: part I—experiment. Compos Part A2013; 48: 93–100.
6.
WuHYTSpringerGS. Measurement of matrix cracking and delamination caused by impact on composite plates. J Compos Mater1988; 22: 518–532.
7.
JoshiSPSunCT. Impact induced fracture in a quasi-isotropic laminate. J Compos Technol Res1987; 9: 40–46.
8.
ShimVPWYangLM. Characterization of the residual mechanical properties of woven fabric reinforced composites after low-velocity impact. Int J Mech Sci2005; 47: 647–665.
9.
KimJKMacKayDBMaiYW. Drop-weight impact damage tolerance of CFRP with rubber-modified epoxy matrix. Composites1993; 24: 485–494.
ChangFKChangKY. Post-failure analysis of bolted composite joints in tension of shear-out mode failure. J Compos Mater1987a; 21: 809–833.
12.
ChangFKChangKY. A progressive damage model for laminated composites containing stress concentration. J Compos Mater1987b; 21: 834–855.
13.
Yen CF. Ballistic impact modeling of composite materials. In: Proceedings 7th International LS-DYNA users conference, 6–15:6–26, Detroit, MI, 2002.
14.
ForghaniAZobeiryNPoursartipAet al.A structural modelling framework for prediction of damage development and failure of composite laminates. J Compos Mater2013; 47: 2553–2573.
15.
MaimiPCamanhoPPMayugoJAet al.A continuum damage model for composite laminates: part I—constitutive model. Mech Mater2007; 39: 897–908.
16.
DonadonMVIannucciLFalzonBGet al.A progressive failure model for composite laminates subjected to low velocity impact damage. Compos Struct2008; 86: 1232–1252.
17.
PhilippidisTPVassilopoulosAP. Stiffness reduction of composite laminates under combined cyclic stresses. Adv Compos Lett2001; 10: 113–124.
18.
DanielIMLeeJW. Damage development in composite laminates under monotonic loading. J Compos Technol Res1990; 12: 98–102.
19.
MirzaaliMJBuerkiASchwiedrzikJet al.Continuum damage interactions between tension and compression in osteonal bone. J Mech Behav Biomed Mater2015; 49: 355–369.
20.
MedinaCCanalesCArangoCet al.The influence of carbon fabric weave on the in-plane shear mechanical performance of epoxy fiber-reinforced laminates. J Compos Mater2014; 48: 2871–2878.
21.
WalterTRSubhashGSankarBVet al.Monotonic and cyclic short beam shear response of 3D woven composites. Compos Sci Technol2010; 70: 2190–2197.
22.
GoldbergRKCarneyKSDuBoisPet al.Development of an orthotropic elasto-plastic generalized composite material model suitable for impact problems. J Aerosp Eng2015; 29: 04015083–1-04015083-11.
23.
HoffarthCRajanSDGoldbergRKet al.Implementation and validation of a three-dimensional plasticity-based deformation model for orthotropic composites. Compos Part A Appl Sci Manufact2016; 91: 336–350.
24.
GoldbergRKCarneyKSDuBoisPet al.Analysis and characterization of damage using a generalized composite material model suitable for impact problems. J Aerosp Eng2018; 31: 04018025-1–04018025-10.
25.
Goldberg RK, Carney KS, DuBois P, et al. Incorporation of damage and failure into an orthotropic elasto-plastic three-dimensional model with tabulated input suitable for use in composite impact problems. In: Proceedings 14th International LS-DYNA users conference, 6–12:6–14, Detroit, MI, 2016.
26.
HoffarthCKhaledBShyamsunderLet al.Verification and validation of a three-dimensional orthotropic plasticity constitutive model using a unidirectional composite. Fibers2017; 5: 12–12.
27.
KhaledBShyamsunderLHoffarthCet al.Experimental characterization of composites to support an orthotropic plasticity material model. J Compos Mater2017; 52: 1847–1872.
28.
ASTM D6641/D6641M-16. Test method for compressive properties of polymer matrix composite materials using a combined loading compression (CLC) test fixture. West Conshohocken, PA: ASTM International, 2016. DOI: 10.1520/D6641_D6641M-16E01.
29.
ASTM D5379/D5379M-12. Test method for shear properties of composite materials by the V-notched beam method. West Conshohocken, PA: ASTM International, 2012. DOI: 10.1520/D5379_D5379M-12.
30.
OdegardGKumosaM. Determination of shear strength of unidirectional composite materials with the Iosipescu and 10 degree off-axis shear tests. Compos Sci Technol2000; 60: 2917–2943.
31.
PierronFVautrinA. Measurement of the in-plane shear strengths of unidirectional composites with the Iosipescu test. Compos Sci Technol1997; 57: 1653–1660.
32.
ASTM D8101/D8101M-17. Standard test method for measuring the penetration resistance of composite materials to impact by a blunt projectile. West Conshohocken, PA: ASTM International, 2017. DOI: 10.1520/D8101_D8101M-17.
33.
Melis ME, Pereira JM, Goldberg RK, et al. Dynamic impact testing and model development in support of NASA’s advanced composites program. In: Proceedings 2018 AIAA Scitech Forum, 1–8:1–12, Kissimmee, FL, 2018.
Nuggehalli Nandakumar P. Rate sensitivity of the interlaminar fracture toughness of laminated composites. Master’s Thesis, Department of Aerospace Engineering, Wichita State University, Wichita, KS, USA, 2010.
