Vacuum bagging allows the removal of trapped air between fabrics layers, extraction of moisture and volatiles, and optimization of the fiber-to-resin ratio. However, during vacuum bagging the compaction pressure is limited to atmospheric pressure, preventing the composite reaching higher fiber volumetric contents and also allows surface porosity to arise, affecting the esthetical appearance of the composite and also its mechanical performance. While the autoclave process has shown to solve these problems, the cost of the equipment is too high for many applications. In the present work, a series of experiments are carried out by compressing unidirectional flax/epoxy vacuum-bagged laminates in a hydraulic press at different pressures. The quality of the laminates is analyzed in terms of surface finish, internal void content, and mechanical properties. The additional compaction from hydraulic pressure is shown to be very effective in improving considerably the overall quality of the composites.
ShahDUSchubelPJLicencePet al.Determining the minimum, critical and maximum fibre content for twisted yarn reinforced plant fibre composites. Compos Sci Technol2012; 72: 1909–1917.
2.
SivaIWinowlinJappesJTet al.Effect of fiber volume fraction on the mechanical properties of coconut sheath/usp composite. J Manuf Eng2013; 8: 60–63.
3.
VarnaJJoffeRBerglundLAet al.Effect of voids on failure mechanisms in RTM laminates. Compos Sci Technol1995; 53: 241–249.
4.
CostaMLdeAlmeidaSFMCerqueiraRezendeM. The influence of porosity on the interlaminar shear strength of carbon/epoxy and carbon/bismaleimide fabric laminates. Compos Sci Technol2001; 61: 2101–2108.
5.
LiYLiQMaH. The voids formation mechanisms and their effects on the mechanical properties of flax fiber reinforced epoxy composites. Compos Part A Appl Sci2015; 72: 40–48.
6.
KimSYShimCSSturtevantCet al.Mechanical properties and production quality of hand-layup and vacuum infusion processed hybrid composite materials for GFRP marine structures. Int J Nav Archit Ocean Eng2014; 6: 723–736.
7.
StringerLG. Optimization of the wet lay-up/vacuum bag process for the fabrication of carbon fibre epoxy composites with high fibre fraction and low void content. Composites1989; 20: 441–452.
8.
HamillLCenteaTNuttS. Surface porosity during vacuum bag-only prepreg processing: causes and mitigation strategies. Compos Part A Appl Sci2015; 75: 1–10.
9.
EomYBooghLMichaudVet al.Stress-initiated void formation during cure of a three-dimensionally constrained thermoset resin. Polym Eng Sci2001; 41: 492–503.
10.
WisnomMRGigliottiMErsoyNet al.Mechanisms generating residual stresses and distortion during manufacture of polymer matrix composite structures. Compos Part A Appl Sci2006; 37: 522–529.
11.
BoyardNMillischerASobotkaVet al.Behaviour of a moulded composite part: modelling of dilatometric curve (constant pressure) or pressure (constant volume) with temperature and conversion degree gradients. Compos Sci Technol2007; 67: 943–954.
12.
PotterKD. The early history of the resin transfer moulding process for aerospace applications. Compos Part A Appl Sci1999; 30: 619–21.
13.
LundströmTS. Measurement of void collapse during resin transfer moulding. Compos Part A Appl Sci1997; 28: 201–14.
14.
AfendiMBanksWMKirkwoodD. Bubble free resin for infusion process. Compos Part A Appl Sci2005; 36: 739–46.
15.
HaiderMHubertPLessardL. An experimental investigation of class a surface finish of composites made by the resin transfer molding process. Compos Sci Technol2007; 67: 3176–3186.
The MathWorks Inc. Matlab Version 8.6.0.267246 (R2015b), Natick, MA: The MathWorks Inc, 2015.
20.
KaneJKarthikCButtDPet al.Microstructural characterization and pore structure analysis of nuclear graphite. J Nucl Mater2011; 415: 189–197.
21.
ASTM D790-15e2. Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials, ASTM International, West Conshohocken, PA, 2015. www.astm.org. DOI: 10.1520/D0790-15E02.
22.
ASTM D3039 / D3039M-14. Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, ASTM International, West Conshohocken, PA, 2014, www.astm.org. DOI: 10.1520/D3039_D3039M-14.
23.
KellyPAUmerRBickertonS. Viscoelastic response of dry and wet fibrous materials during infusion processes. Compos Part A Appl Sci2006; 37: 868–873.
24.
ChenBLangEJChouTW. Experimental and theoretical studies of fabric compaction behavior in resin transfer molding. Mater Sci Eng A2001; 317: 188–196.
25.
ChenBChouTW. Compaction of woven-fabric preforms in liquid composite molding processes: single-layer deformation. Compos Sci Technol1999; 59: 1519–1526.
26.
SomashekarAABickertonSBhattacharyyaD. An experimental investigation of non-elastic deformation of fibrous reinforcements in composites manufacturing. Compos Part A Appl Sci2006; 37: 858–867.
27.
RobitailleFGauvinR. Compaction of textile reinforcements for composites manufacturing. III: reorganization of the fiber network. Polym Compos1999; 20: 48–61.
28.
FrancucciGRodriguezEVazquezA. Experimental study of the compaction response of jute fabrics in liquid composite molding processes. J Compos Mater2012; 46: 155–167.
29.
AndersMLoJCenteaTet al.Eliminating volatile-induced surface porosity during resin transfer molding of a benzoxazine/epoxy blend. Compos Part A Appl Sci2016; 84: 442–454.
30.
CharletKBaleyCMorvanCet al.Characteristics of Hermès flax fibres as a function of their location in the stem and properties of the derived unidirectional composites. Compos Part A Appl Sci2007; 38: 1912–1921.
31.
GningPBLiangSGuillaumatLet al.Influence of process and test parameters on the mechanical properties of flax/epoxy composites using response surface methodology. Mater Sci2011; 46: 6801–6801.
32.
OksmanK. High quality flax fibre composites manufactured by the resin transfer moulding process. J Reinf Plast Compos2001; 20: 621–627.
33.
HeijenrathRPeijsT. Natural-fibre-mat-reinforced thermoplastic composites based on flax fibres and polypropylene. Adv Compos Lett1996; 5: 81–85.
