In this study, a mixture of vinyl ester (VER) and polyurethane (PU) prepolymer was used in the field of pipe manufacturing as a matrix material (interpenetrating polymer networks) with E-glass fibre as reinforcement. In order to evaluate the mechanical strength of the fibre-reinforced VER-PU interpenetrating polymer network composite pipe, tests like hydrostatic, hoop, stiffness, and axial compression were conducted systematically with five proportions of PU-loaded VER (0%, 10%, 20%, 30%, 40%, and 50%). It was observed that during the stiffness test, all the PU-loaded VER specimens have regained its original shape, size, and also retains its structural integrity. VER glass fibre composite pipes (0% PU) exhibited crazing, wall delamination, and rupture on compression. With increase in PU content, there were no such effects after the compression, but a slight drop in mechanical properties like hoop, stiffness, and axial compression was observed. The obtained experimental results were found to be in good agreement with finite element analysis data.
HossainME. The current and future trends of composite materials: an experimental study. J Compos Mater2011; 45: 2133–2144.
2.
SariMKarakuzuRDenizME. Residual failure pressures and fatigue life of filament-wound composite pipes subjected to lateral impact. J Compos Mater2011; 46: 1787–1794.
3.
Nixon-PearsonOJHallettSR. An experimental investigation into quasi-static and fatigue damage development in bolted-hole specimens. Compos Part B: Eng2015; 77: 462–473.
4.
PirvuAGardnerDJLopez-AnidoR. Carbon fibre-vinyl ester composite reinforcement of wood using the VARTM/SCRIMP fabrication process. Compos Part A: Appl Sci Manuf2004; 35: 1257–1265.
5.
KangHMYoonTHBumpM. Effect of solubility and miscibility on the adhesion behavior of polymer-coated carbon fibres and vinyl ester resins. J Appl Polym Sci2001; 79: 1042–1053.
6.
Taillemite S and Pauer R. Bright future for vinylester resins in corrosion applications. Reinf Plast2009; 53: 34–37.
7.
HusicSJavaniIPetrovicZS. Thermal and mechanical properties of glass reinforced soy-based polyurethane composites. Compos Sci Technol2005; 65: 19–25.
8.
ChattopadhyayDKRajuKVSN. Structural engineering of polyurethane coatings for high performance applications. Prog Polym Sci2007; 32: 352–418.
9.
RaquezJMDelegliseMLacrampeMF. Thermosetting (bio) materials derived from renewable resources: a critical review. Prog Polym Sci2010; 35: 487–509.
10.
CristeaMIbanescuSCascavalCN. Dynamic mechanical analysis of polyurethane-epoxy interpenetrating polymer networks. High Perform Polym2009; 21: 608–623.
11.
WangGYWangYLHuCP. Interpenetrating polymer networks of polyurethane and graft vinyl ester resin: polyurethane formed with toluene diisocyanate. Eur Polym J2000; 36: 735–742.
12.
QinC-LCaiW-MCaiJ. Damping properties and morphology of polyurethane/vinyl ester resin interpenetrating polymer network. Mater Chem Phys2004; 85: 402–409.
13.
FanLHHuCPYingSK. Thermal analysis during the formation of polyurethane and vinyl ester resin interpenetrating polymer networks. Polymer1996; 37: 887–1058.
14.
Al-SulaimanFKhanKMerahN. Effects of weathering on failure pressure of filament-wound GFRP thermoset pipes. J Compos Mater2010; 45: 645–655.
15.
GoertzenWKKesslerMR. Dynamic mechanical analysis of carbon/epoxy composites for structural pipeline repair. Compos Part B: Eng2007; 38: 1–9.
16.
GningaPBTarfaouiaMCollombetbF. Damage development in thick composite tubes under impact loading and influence on implosion pressure: experimental observations. Compos Part B: Eng2005; 36: 306–318.
17.
CzelGCziganyT. A study of water absorption and mechanical properties of glass fibre/polyster composite pipes – effects of specimen geometry and preparation. J Compos Mater2008; 42: 2815–2827.
18.
TarakciogluNSamanciAArikanH. The fatigue behavior of (±55°)3 filament wound GRP pipes with a surface crack under internal pressure. Compos Struct2007; 80: 207–211.
19.
SariMKarakuzuRDenizME. Residual failure pressures and fatigue life of filament-wound composite pipes subjected to lateral impact. J Compos Mater2011; 46: 1787–1794.
20.
ASTM D1599. Standard test method for resistance to short-time hydraulic pressure of plastic pipe, tubing, and fittings. 2010.
21.
ASTM D2290. Standard test method for apparent hoop tensile strength of plastic or reinforced plastic pipe by split disk method. 2010.
22.
ASTM D2412. Standard test method for determination of external loading characteristics of plastic pipe by parallel-plate loading. 2010.
23.
ASTM D695. Standard test method for compressive properties of rigid plastics. 2010.
24.
Structural Analysis Guide. Release 12.1. Available at: http://www.ansys.com (2009, accessed 25 October 2015).
25.
ShishesazMShishesazMR. Applicability of medium density polyethylene gas pipes in hot climate areas of south-west Iran. Iranian Polym J2008; 17: 503–517.
26.
MackerleJ. Finite element analyses and simulations of manufacturing processes of composites and their mechanical properties: a bibliography (1985–2003). Comput Mater Sci2004; 31: 187–219.
27.
WangTChenSWangQ. Damping analysis of polyurethane/epoxy graft interpenetrating polymer network composites filled with short carbon fibre and micro hollow glass bead. Mater Des2010; 31: 3810–3815.
SureshGJayakumariLS. Evaluating the mechanical properties of E-Glass fibre/carbon fibre reinforced interpenetrating polymer networks. Polimeros2015; 25: 49–57.
30.
NayakRTarkesDPSatapathyA. A computational and experimental investigation on thermal conductivity of particle reinforced epoxy composites. Comput Mater Sci2010; 48: 576–581.
31.
Nahas MN and Alzahrani MA. Restoration of natural frequency of cracked cantilever beam using CNT composite patch: a finite element study. Math Prob Eng 2013; 2013: Article ID 678412, http://dx.doi.org/10.1155/2013/678412 (accessed 25 October 2015).
32.
MeloJDDNetoFLBarrosGA. Mechanical behavior of GRP pressure pipes with addition of quartz sand filler. J Compos Mater2010; 45: 717–726.
