Behaviour of hollow pultruded GFRP square beams with different shear span-to-depth ratios

Abstract

It is important to determine accurately the elastic properties of fibre-reinforced polymer composites material, considering that their member design is often governed by deflection rather than strength. In this study, the elastic properties of the pultruded glass fibre-reinforced polymer square sections were evaluated firstly using full-scale with different shear span to depth (a/d) ratios and tested under static four-point bending. Back calculation and simultaneous methods were then employed to evaluate the flexural modulus and shear stiffness and were compared with the results of the coupon tests. Secondly, the full-scale beams were tested up to failure to determine their capacity and failure mechanisms. Finally, prediction equations describing the behaviour of the pultruded glass fibre-reinforced polymer square beams were proposed and compared with the experimental results. The results indicate that the back calculation method gives more reliable values of elastic properties of glass fibre-reinforced polymer profiles. In addition, the behaviour of the beams is strongly affected by the a/d ratios. The shear was found to have a significant contribution on the behaviour of beams with lower a/d ratios while the flexural stress played a major part for higher a/d ratios. The proposed equation, which accounts for the combined effect of the shear and flexural stresses, reasonably predicted the failure load of pultruded glass fibre-reinforced polymer square beams.

Keywords

Elastic properties characterization shear flexural failure load GFRP beams

Get full access to this article

View all access options for this article.

References

Bakis

Bank

Brown

. Fiber-reinforced polymer composites for construction-state-of-the-art review. J Compos Constr 2002; 6: 73–87.

Hollaway

. A review of the present and future utilisation of FRP composites in the civil infrastructure with reference to their important in-service properties. Constr Build Mater 2010; 24: 2419–2445.

Bank

. Shear coefficients for thin-walled composite beams. Compos Struct 1987; 8: 47–61.

Barbero

S-H

Raftoyiannis

. Ultimate bending strength of composite beams. J Mater Civil Eng 1991; 3: 292–306.

Omidvar

. Shear coefficient in orthotropic thin-walled composite beams. J Compos Constr 1998; 2: 46–56.

Nagaraj

GangaRao

. Static behavior of pultruded GFRP beams. J Compos Constr 1997; 1: 120–129.

Bank

. Composite for construction structural design with FRP materials, NJ: Jone Wiley & Sons, 2006, pp. 551–551.

Davalos

Salim

Qiao

Lopez-Anido

Barbero

. Analysis and design of pultruded FRP shapes under bending. Compos B: Eng 1996; 27: 295–305.

Roberts

Masri

. Section properties and buckling behavior of pultruded FRP profiles. J Reinf Plast Compos 2003; 22: 1305–1317.

10.

Manalo

Mutsuyoshi

Matsui

. Testing and characterization of thick hybrid fibre composites laminates. Int J Mech Sci 2012; 63: 99–109.

11.

Cardoso D, Harries K and Batista E. On the determination of mechanical properties for pultruded GFRP sections. In: International conference on FRP composites in Civil Engineering. Vancouver, Canada: Internationl Institute for FRP in Construction, 2014.

12.

Guades

Aravinthan

Islam

. Characterisation of the mechanical properties of pultruded fibre-reinforced polymer tube. Mater Des 2014; 63: 305–315.

13.

Bank

. Flexural and shear moduli of full-section fiber reinforced plastic(FRP) pultruded beams. J Test Eval 1989; 17: 40–45.

14.

Neto

Rovere

. Flexural stiffness characterization of fiber reinforced plastic (FRP) pultruded beams. Compos Struct 2007; 81: 274–282.

15.

Mottram

. Shear modulus of standard pultruded fiber reinforced plastic material. J Compos Constr 2004; 8: 141–147.

16.

Chambers

. ASCE design standard for pultruded fiber-reinforced-plastic (FRP) structures. J Compos Constr 1997; 1: 26–38.

17.

Parke

Hewson

. ICE manual of bridge engineering. History 2008; 6: 3–3.

18.

ISO 1172. Textile-glass-reinforced plastics, prepegs, moulding compounds and laminates: Determination of the textile-glass and mineral-filler content – calcination methods, 1996.

19.

ASTM D7250. ASTM D7250/D7250M-06 Standard practice for determine sandwich beam flexural and shear stiffeness, West Conshohocken, PA: ASTM International, 2006.

20.

Hayes M and Lesko J. The effect of non-classical behaviors on the measurement of the Timoshenko shear stiffness. In: Proc 2nd inter conf FRP composites in civil engineering – CICE, 2004, pp. 873–880.

21.

Bai

. Web crippling behaviour of pultruded glass fibre reinforced polymer sections. Compos Struct 2014; 108: 789–800.

22.

Kumar

Chandrashekhara

Nanni

. Structural performance of a FRP bridge deck. Constr Build Mater 2004; 18: 35–47.

23.

Roberts

Al-Ubaidi

. Flexural and torsional properties of pultruded fiber reinforced plastic I – profiles. J Compos Constr 2002; 6: 28–34.

24.

Dai

Hahn

. Flexural behavior of sandwich beams fabricated by vacuum-assisted resin transfer molding. Compos Struct 2003; 61: 247–253.

25.

Yoshihara

Furushima

. Shear strengths of wood measured by various short beam shear test methods. Wood Sci Technol 2003; 37: 189–197.

26.

Awad

Aravinthan

Manalo

. Geometry effect on the behaviour of single and glue-laminated glass fibre reinforced polymer composite sandwich beams loaded in four-point bending. Mater Des 2012; 39: 93–103.

27.

Turvey

Zhang

. Shear failure strength of web–flange junctions in pultruded GRP WF profiles. Constr Build Mater 2006; 20: 81–89.

28.

ASCE. Structural Plastics Design Manual. ASCE manuals and reports on engineering practice 63, Reston, VA: American Society of Civil Engineering, 1984.