Nickel matrix composites reinforced with different weight percent of alumina short fibres have been fabricated by powder technology route. The alumina short fibres were encapsulated by nickel layers using the electroless deposition technique. The produced alumina/nickel composite powders underwent cold compaction and sintering at 850℃. The alumina/nickel powders as well as the consolidated composites were investigated by optical microscope, scanning electron microscope, XRD and VSM. It was observed that the surface of the alumina short fibres was completely coated with nickel layer and the microstructures of the consolidated compacts show homogeneous distribution of the alumina short fibres in the nickel matrix. The density, electrical conductivity, coercivity, retentivity, saturation magnetization and hardness of the produced alumina short fibres/nickel composites were measured. The relative sintered density and the saturation magnetization were decreased, but the retentivity, the coercivity and the hardness were increased by increasing the alumina short fibres weight percent in the nickel matrix.
GaneshVVChawlaN. Effect of particle orientation anisotropy on the tensile behavior of metal matrix composites: experiments and microstructure-based simulation. Mater Sci Eng A2005; 391: 342–353.
2.
ZhangHChenMWRameshKT. Tensile behavior and dynamic failure of aluminum 6092/B4C composites. Mater Sci Eng A2006; 433: 70–82.
3.
LloydDJ. Aspects of fracture in particulate reinforced metal matrix composites. Acta Metallurgica et Mater1991; 39: 59–71.
4.
LloydDJ. Particle reinforced aluminum and magnesium matrix composites. Int Mater Rev1994; 39: 1–23.
5.
ClyneTWWithersPJ. An introduction to metal matrix composites, Cambridge: Cambridge University Press, 1993, pp. 73–73.
6.
GarcesGBrunoGWannerA. Load transfer in short fibre reinforced metal matrix composites. Acta Materialia2007; 55: 5389–5400.
7.
GarciaDESchickerSJanssenR. Nb- and Cr-Al2O3 composites with interpenetrating networks. J Eur Ceram Soc1998; 18: 601–605.
8.
Harrigan WC. In: Everett RK and Arsenault RJ (eds) Metal matrix composites: processing and interfaces. Boston (MA): Academic Press, 1991, pp. 1–16.
9.
LiJWuYYWangDL. The microstructure and wear resistance characteristics of electroformed nickel and partially stabilized zirconia composite coatings. J Mater Sci2000; 35: 1751–1758.
10.
LiangXSOuyangJHLiYF. Electrodeposition and tribological properties of Ni–SrSO4 composite coatings. J App Surf Sci2009; 255: 4316–4321.
11.
ArunaSTWilliam GripsVKRajamKS. Synthesis and characterization of Ni–Al2O3 composite coatings containing different forms of alumina. J App Electrochem2010; 40: 2161–2169.
12.
ChenLWangLZengZ. Effect of surfactant on the electrodeposition and wear resistance of Ni–Al2O3 composite coatings. Mater Sci Eng A2006; 434: 319–325.
13.
ChenLWangLZengZ. Influence of pulse frequency on the microstructure and wear resistance of electrodeposited Ni-Al2O3 composite coatings. Surf Coat Technol2006; 201: 599–605.
14.
BahrololoomMESaniR. The influence of pulse plating parameters on the hardness and wear resistance of nickel–alumina composite coatings. Surf Coat Technol2005; 192: 154–163.
15.
SzczygielBKolodziejM. Composite Ni/Al2O3 coatings and their corrosion resistance. Electrochim Acta2005; 50: 4188–4195.
16.
HongtaoCJinqiuZMaozhongA. Influences of SiC Concentration on Sn/SiC Nanocomposite Electrodeposition. Int J Electrochem Sci2013; 8: 1871–1884.
17.
García-LecinaEGarcía-UrrutiaIDíezJA. A comparative study of the effect of mechanical and ultrasound agitation on the properties of electrodeposited Ni/Al2O3 nanocomposite coatings. Surf Coat Technol2012; 206: 2998–3005.
18.
KellyA. Strong solids, Oxford: Clarendon Press, 1973, pp. 1–212.
19.
LaBelleHEJrMlavskyAI. Growth of sapphire filaments from the melt. Nature1967; 216: 574–575.
20.
MileikoST. Oxide fiber-Ni-base matrix composites – III. A creep model and analysis of experimental data. Compos Sci Technol2002; 62: 195–204.
21.
MileikoSTSarkissyanNSKolchinAA. Oxide fibers in a Ni-base matrix: do they degrade or become stronger?J Mater Des Appl2004; 218: 193–200.
22.
ZhitomirskyINiewczasMPetricA. Synthesis and magnetic properties of Ni-Zirconia. Compos Mater Manuf Proc2003; 18: 719–730.
23.
FahrenholtzWGEllerbyDTLoehmanRE. Al2O3 – Ni composites with high fracture strength and fracture toughness. J Am Ceram Soc2000; 83: 27–32.
24.
RoyRARoyR. Dispersic xerogels: ceramic – metal composites. Mater Res Bull1984; 19: 169–177.
25.
BrevalEDoddsGPantanoCG. Properties and microstructure of Ni – alumina composite materials prepared by the sol/gel method. Mater Res Bull1984; 20: 1191–1205.
26.
RoyR. Ceramics by the solution-sol-gel route. Science1987; 238: 1664–1669.
27.
BrevalEPantanoCG. Sol–gel prepared Ni – alumina composite materials: part I. Structure and hot-pressing temperature. J Mater Sci1992; 27: 5463–5469.
28.
RodeghieroEDTseOKChisakiJ. Synthesis and properties of Ni-Al2O3 composites via sol–gel. Mater Sci Eng A Struct Mater: Prop Microstruct Process1995; A195: 151–161.
29.
BrevalEDengZShiouS. Sol–gel prepared Ni–alumina composite materials: part I. Microstructure and mechanical properties. J Mater Sci1992; 27: 1464–1468.
30.
TuanWHLinMCWuHH. Preparation of Al2O3/Ni composites by pressureless sintering in H 2. Ceram Int1995; 21: 221–225.
SekinoTNakajimaTUedaS. Reduction and sintering of nickel-dispersed-alumina composite and its properties. J Am Ceram Soc1998; 80: 1139–1148.
33.
LawnBRSwainMV. Microfracture beneath points indentations in brittle solids. J Mater Sci1975; 10: 113–122.
34.
SilvainJFBihrJCDouinJ. Wettability, reactivity and stress relaxation of an NiAl(Ti)/Al2O3 composite. Composites1998; 29: 1175–1183.
35.
HoweJM. Bonding, structure, and properties of metal/ceramic interfaces: Part 1. Chemical bonding, chemical reaction, and interfacial structure. Int Mater Rev1993; 38: 233–256.
36.
MerlinVEustathopoulosN. Wetting and adhesion of Ni-Al alloys on Al2O3 single crystals. J Mater Sci1995; 30: 3619–3624.
37.
RamsJUrenaACampoJ. Sol-gel coatings as active barriers to protect ceramic reinforcement in aluminum matrix composites. Adv Eng Mater2004; 6: 57–61.
38.
WenTGaoJShenJ. Preparation and characterization of TiO2 thin films by the sol-gel process. J Mater Sci2001; 36: 5923–5926.
39.
YangGFanTZhangD. Chemical reaction in Al matrix composite reinforced with SiCp coated by SnO2. J Mater Sci2004; 39: 3689–3694.
40.
LiboLMaozhongAGaohuiW. A new electroless nickeldeposition technique to metallise SiCp/Al composites. Surf Coat Tech2004; 200: 5102–5112.
41.
SridharSWToguriRStephensonJM. Wettability of nickel coated graphite by aluminium. Mater Sci Eng A1998; 244: 31–38.
42.
KimDHAokiKTakanoO. Electroless plating of Ni-Co-Fe-P alloy for soft magnetic thin films. J Surf Technol Japan1995; 46: 81–82.
PerkinsJ. Residual stresses and the origin of reversible (two-way) shape memory effects. Scr Metall1974; 8: 1469–1476.
45.
LowenheimFA. Modern electroplating, New York, NY: John Wiley and Sons, 1974.
46.
Cristina OliveiraMBotelho do RegoAM. The effect of the hypophosphite ion oxidation on the Ni surface electrode-an XPS study. J Alloy Comp2006; 425: 64–68.
47.
LeeDDKangSJYoonDN. Mechanism of grain growth and a-b transformation during liquid-phase sintering of b -Sialon. J Am Ceram Soc1988; 71: 803–809.
48.
KangSJHanSM. Grain growth in Si3N4 based materials. MRS Bull1995; 20: 33–37.
49.
HanSMKangSJ. Comment on kinetics of Si3N4 grain growth in Si3N4 ceramics sintered under high nitrogen pressure. J Am Ceram Soc1993; 76: 3178–3185.
50.
YeHPujarVVPadtureNP. Coarsening in liquid-phase-sintered SiC. Acta Mater1999; 47: 481–489.
51.
AndrénHORolanderULindahlP. Phase composition in cemented carbides and cermets. Int J Refract Met Hard Mater1993; 12: 107–112.
52.
PavlatouEARaptakisMSpyrellisN. Synergistic effect of 2-butyne-1,4-diol and pulse plating on the structure and properties of nickel nanocrystalline deposits. Surf Coat Technol2007; 201: 4571–4577.
53.
GyftouPStroumbouliMPavlatouEA. Hardening effect induced by incorporation of SiC particles in Ni electrodeposits. Electrochim Acta2005; 50: 4544–4550.
54.
ZhangHChenMWRameshKT. Tensile behavior and dynamic failure of aluminum 6092/B4C composites. Mater Sci Eng A2006; 433: 70–82.
AldrichDEFanZ. Micro structural characterisation of interpenetrating nickel/alumina composites. Mater Character2001; 47: 167–173.
57.
UrenARamsJEscaleraMD. Characterization of interfacial mechanical properties in carbon fiber/aluminium matrix composites by the nanoindentation technique. Compos Sci Technol2005; 65: 2025–2038.
58.
RamsJUrenAEscaleraMD. Electroless nickel coated short carbon fibers in aluminum matrix composites. Compos Part A2007; 38: 566–575.
59.
MontesJMCuevasFGCintasJ. Porosity effect on the electrical conductivity of sintered powder compacts. Appl Phys A2008; 92: 375–380.
60.
MoustafaSFDaoushWM. Synthesis of nano-sized Fe–Ni powder by chemical process for magnetic applications. J Mater Process Technol2007; 181: 59–63.
61.
DaoushWMLeeKHParkHS. Effect of liquid phase composition on the microstructure and properties of (W,Ti)C cemented carbide cutting tools. Int J Refract Metal Hard Mater2009; 27: 83–89.
62.
DaoushWMParkHSLeeKH. Effect of binder compositions on microstructure, hardness and magnetic properties of (Ta,Nb)C–Co and (Ta,Nb)C–Ni cemented carbides. Int J Refract Metal Hard Mater2009; 27: 669–675.
63.
DaoushWMoustafaSKayetbayS. Processing of metallic filters by powder metallurgy technique. Powder Metall Prog2006; 6: 164–168.
64.
DaoushW. Processing of FeCo nanosized soft-magnetic material by powder metallurgy technique. Mater Sci Forum2007; 558: 707–7010.
65.
DaoushWMoustafaSF. Coating points a way for synthesis of tough intermetallics. Met Powder Rep2007; 1: 30–33.
