Effects of different volume fractions of reinforcement and various loads applied in wear testing on dry tribological behavior of Al-Al3Ti in-situ composite were investigated. Mixture of aluminum and different amount of titanium powders has been compacted and combustion synthesized to obtain Al-Al3Ti composite with different percent of reinforcements. The results of pin-on-disk wear tests indicated that addition of Al3Ti to aluminum matrix increase wear resistance of the composite samples by 4 times compared to that of pure aluminum. In addition, presence of Al3Ti reinforcement reduced friction coefficient of the composites. Oxidation/abrasive mechanism was revealed to be dominant on wear behavior of Al-Al3Ti composites; adhesive wear decreased as volume fraction of the intermetallic increased in the composites.
XuJLiuW. Wear characteristic of in situ synthetic TiB2 particulate-reinforced Al matrix composite formed by laser cladding. Wear2006; 260(4–5): 486–492.
2.
RameshCSAhamedA. Friction and wear behaviour of cast Al 6063 based in situ metal matrix composites. Wear2011; 271(9–10): 1928–1939.
3.
KumarSSarmaVSMurtyBS. High temperature wear behavior of Al–4Cu–TiB2 in situ composites. Wear2010; 268(11–12): 1266–1274.
4.
LiuJBinnerJHigginsonR. Dry sliding wear behaviour of co-continuous ceramic foam/aluminium alloy interpenetrating composites produced by pressureless infiltration. Wear2012; 276–277(0): 94–104.
5.
ZhangZHanBQWitkinD. Synthesis of nanocrystalline aluminum matrix composites reinforced with in situ devitrified Al–Ni–La amorphous particles. Scripta Materialia2006; 54(5): 869–874.
6.
AlbiterAContrerasABedollaE. Structural and chemical characterization of precipitates in Al-2024/TiC composites. Compos Part A: Appl Sci Manuf2003; 34(1): 17–24.
7.
FerreiraSCSequeiraPDWatanabeY. Microstructural characterization and tribocorrosion behaviour of Al/Al3Ti and Al/Al3Zr FGMs. Wear2011; 270(11–12): 806–814.
8.
HsuCJKaoPWHoNJ. Intermetallic-reinforced aluminum matrix composites produced in situ by friction stir processing. Mater Lett2007; 61(6): 1315–1318.
WatanabeYYamanakaNFukuiY. Wear behavior of Al-Al3Ti composite manufactured by a centrifugal method. Metall and Mat Trans A1999; 30(12): 3253–3261.
11.
ZhangSZhaoYChenG. Microstructures and dry sliding wear properties of in situ Al composites. J Mater Process Technol2007; 184(1–3): 201–208.
12.
El-HadadSSatoHWatanabeY. Investigation of wear anisotropy in a severely deformed Al-Al3Ti composite. Metall and Mat Trans A2012; 43(9): 3249–3256.
13.
WuSQZhuHGTjongSC. Wear behavior of in situ Al-based composites containing TiB2, Al2O3, and Al3Ti particles. Metall and Mat Trans A1999; 30(1): 243–248.
14.
TorresBLieblichMIbáñezJ. Mechanical properties of some PM aluminide and silicide reinforced 2124 aluminium matrix composites. Scripta Materialia2002; 47(1): 45–49.
15.
Muñoz-MorrisMARexachJILieblichM. Comparative study of Al-TiAl composites with different intermetallic volume fractions and particle sizes. Intermetallics2005; 13(2): 141–149.
16.
PengLMLiHWangJH. Processing and mechanical behavior of laminated titanium–titanium tri-aluminide (Ti–Al3Ti) composites. Mater Sci Eng A2005; 406(1–2): 309–318.
17.
MorsiK. The diversity of combustion synthesis processing: a review. J Mater Sci2012; 47(1): 68–92.
18.
ArunaSTMukasyanAS. Combustion synthesis and nanomaterials. Curr Opin Solid State Mater Sci2008; 12(3–4): 44–50.
19.
PatilKCArunaSTMimaniT. Combustion synthesis: an update. Curr Opin Solid State Mater Sci2002; 6(6): 507–512.
20.
MorsiK. Review: reaction synthesis processing of Ni–Al intermetallic materials. Mater Sci Eng: A2001; 299(1–2): 1–15.
21.
LeeS-HLeeJ-HLeeY-H. Effect of heating rate on the combustion synthesis of intermetallics. Mater Sci Eng A2000; 281(1–2): 275–285.
22.
StraffeliniGPellizzariMMolinariA. Influence of load and temperature on the dry sliding behaviour of Al-based metal-matrix-composites against friction material. Wear2004; 256(7–8): 754–763.
23.
LeeGYDharanCKHRitchieRO. A physically-based abrasive wear model for composite materials. Wear2002; 252(3–4): 322–331.
24.
OcelíkVMatthewsDDe HossonJTM. Sliding wear resistance of metal matrix composite layers prepared by high power laser. Surf Coat Technol2005; 197(2–3): 303–315.
25.
KimHYChungDSHongSH. Reaction synthesis and microstructures of NiAl/Ni micro-laminated composites. Mater Sci Eng A2005; 396(1–2): 376–384.
26.
G99-04 A. Standard test method for wear testing with a Pin-on-Disk apparatus. West Conshohocken, PA: ASTM International, 2004.
27.
Taheri M and Habibolahzadeh A. Production of in-situ Al-Al3Ti composite with method combustion synthesis. In: 8th national seminar on heat treatment and surface engineering (ed B Ghasemi), Kerman, Iran, May 2007, pp.438–42. Kerman, Iran: Kerman University Publications.
28.
Nembach E. Particle strengthening of metals and alloys: New York: J Wiley, 1997.
29.
KumarSSubramanya SarmaVMurtyBS. Effect of temperature on the wear behavior of Al-7Si-TiB 2 in-situ composites. Metallurgic Mater Transac A: Phys Metallurgy Mater Sci2009; 40(1): 223–231.
30.
HutchingsIMWilsonSAlpasAT3.19 - Wear of aluminum-based composites. In: AnthonyKCarlZ (eds). Comprehensive composite materials, Oxford: Pergamon, 2000, pp. 501–519.
