Life cycle strain monitoring in glass fibre reinforced polymer laminates using embedded fibre Bragg grating sensors from manufacturing to failure

Abstract

A holistic approach to strain monitoring in fibre-reinforced polymer composites is presented using embedded fibre Bragg grating sensors. Internal strains are monitored in unidirectional E-glass/epoxy laminate beams during vacuum infusion, curing, post-curing and subsequent loading in flexure until failure. The internal process-induced strain development is investigated through use of different cure schedules and tool/part interactions. The fibre Bragg grating sensors successfully monitor resin flow front progression during infusion, and strain development during curing, representative of the different cure temperatures and tool/part interfaces used. Substantial internal process-induced strains develop in the transverse fibre direction, which should be taken into consideration when designing fibre-reinforced polymer laminates. Flexure tests indicate no significant difference in the mechanical properties of the differently cured specimens, despite the large differences in measured residual strains. This indicates that conventional flexure testing may not reveal residual strain or stress effects at small specimen scale levels. The internal stresses are seen to influence the accuracy of the fibre Bragg gratings within the loading regime. This study confirms the effectiveness of composite life cycle strain monitoring for developing consistent manufacturing processes.

Keywords

Strain monitoring fibre Bragg grating sensors curing process-induced strains life cycle composite

Get full access to this article

View all access options for this article.

References

Favre

. Residual thermal stresses in fibre reinforced composite materials - a review. J Mech Behav Mater 1988; 1(1–4): 37–53.

Hahn

. Effects of residual stresses in polymer/matrix composites. J Astronaut Sci 1984; 32(2): 253–267.

Bogetti

Gillespie

. Process-induced stress and deformation in thick-section thermoset composite laminates. J Compos Mater 1992; 26: 626–659.

Kim

Hahn

. Residual stress development during processing of graphite/epoxy composites. Compos Sci Technol 1989; 36: 121–132.

Zhao

Warrior

Long

. A micromechanical study of residual stress and its effect on transverse failure in polymer-matrix composites. Int J Solids Struct 2006; 43: 5449–5467.

Stone

Schwarz

Chandler

. Residual stresses associated with post-cure shrinkage in GRP tubes. Compos Sci Technol 1997; 57: 47–54.

Nedele

Wisnom

. Three-dimensional finite element analysis of the stress concentration at a single fibre break. Compos Sci Technol 1994; 51(4): 517–524.

Johnston A. An integrated model of the development of process-induced deformation in autoclave processing of composite structures. PhD Thesis, University of British Columbia, Vancouver, Canada, 1997.

Svanberg JM. Predictions of manufacturing induced shape distortions - high performance thermoset composites. PhD Thesis, Luleå University of Techology, Luleå, Sweden, 2002.

10.

Twigg

Poursartip

Fernlund

. Tool-part interaction in composites processing. Part II: numerical modelling. Composites Part A 2004; 35: 135–141.

11.

Wisnom

Gigliotti

Ersoy

. Mechanisms generating residual stresses and distortion during manufacture of polymer-matrix composite structures. Composites Part A 2006; 37: 522–529.

12.

Fernlund

Rahman

Courdji

. Experimental and numerical study of the effect of cure cycle, tool surface, geometry, and lay-up on the dimensional fidelity of autoclave-processed composite parts. Composites Part A 2002; 33: 341–351.

13.

Luyckx

Voet

Lammens

. Strain measurements of composite laminates with embedded fibre Bragg gratings: criticism and opportunities for research. Sensors 2011; 11: 384–408.

14.

Eum SH, Kageyama K, Murayama H, et al. Process/health monitoring for wind turbine blade by using FBG sensors with multiplexing techniques. In: Proceedings of SPIE 2008 conference, Perth, Australia, 14–18 April, 2008, vol. 7004, pp.5B1–5B4.

15.

Khoun

de Oliviera

Michaud

. Investigation of process-induced strains development by fibre Bragg grating sensors in resin transfer moulded composites. Composites Part A 2011; 42: 274–282.

16.

Parlevliet P, Voet E, Bersee H, et al. Process monitoring with FBG sensors during vacuum infusion of thick composite laminates. In: Proceedings of 16th ICCM conference, Kyoto, Japan, 3–8 July 2007.

17.

De Waele W. Structural monitoring of composite elements using optical fibres with Bragg sensors. PhD Thesis, Ghent University, Ghent, Belgium, 2002.

18.

Guemes

Mendez

. Response of Bragg grating fiber-optic sensors when embedded in composite laminates. Compos Sci Technol 2002; 62: 959–966.

19.

Nielsen

Schmidt

Hattel

. In-situ measurement using FBGs of process-induced strains during curing of thick glass/epoxy laminate plate: experimental results and numerical modelling. Wind Energy 2012. DOI: 10.1002/we.1550.

20.

Mulle

Collombet

Olivier

. Assessment of cure-residual strains through the thickness of carbon-epoxy laminated using FBGs Part II: technological specimen. Composites Part A 2009; 40: 1534–1544.

21.

Parlevliet

Bersee

Beukers

. Measurement of (post-) curing strain development with fibre Bragg gratings. Polym Test 2010; 29: 291–301.

22.

de Oliviera

Lavanchy

Chatton

. Experimental investigation of the effect of the mould thermal expansion on the development of internal stresses during carbon fibre composite processing. Composites Part A 2008; 39: 1083–1090.

23.

Eum SH, Kageyama K, Murayama H, et al. Resin flow front monitoring for VARTM using fiber Bragg gratings. In: Proceedings 16th ICCM conference, Kyoto, Japan, 8–13 July 2007.

24.

Gupta

Sundaram

. Fiber optic sensors for monitoring flow in vacuum enhanced resin infusion technology (VERITy) process. Composites Part A 2009; 40(8): 1065–1070.

25.

Saton

Fukuchi

Kurosawa

. Polyimide-coated small-diameter optical fiber sensors for embedding in composite laminate structures. Proc SPIE 2001; 4328: 285–294.

26.

Jensen

Sirkis

Integrity of composite structures with embedded optical fibers. In: Udd

(eds). Fiber optic smart structures, New York: Wiley, 1995, pp. 109–129.

27.

Hodgkinson

. Mechanical testing of advanced fibre composites, Boca Raton, FL: CRC Press, 2000.

28.

Dow Chemical Company. Airstone Infusion systems, Form No. 296-01856-0808-BH, 2012.