Solidification processing followed by hot coextrusion was used to fabricate a bimetal magnesium/aluminum macrocomposite containing millimeter-scale Al core reinforcement. Microstructural characterization revealed limited interfacial interdiffusion of both metals into each other. Compressive testing revealed that the presence of Al core does not affect 0.2%YS, marginally decreases ultimate compressive strength (UCS), and significantly increases failure strain (115%) and work of fracture (55%) of Mg. The effect of the presence of mm-scale Al core on the compressive properties of the bimetal macrocomposite is investigated in this article.
Avedesian, M.M. and Baker, H. (ed.) (1999). Metallurgy and Alloys, ASM Specialty Handbook: Magnesium and Magnesium Alloys, pp. 4-6, 37, 274, ASM International®, Ohio, USA.
2.
Bayerische Motoren Werke (BMW) GmbH (2005). Group Management Report, Annual Report 2005 (English version), p. 20, Munich, Germany.
3.
Janecek, M., Popov, M., Krieger, M.G., Hellmig, R.J. and Estrin, Y. (2007). Mechanical Properties and Microstructure of a Mg Alloy AZ31 Prepared by Equal - Channel Angular Pressing, Materials Science and Engineering A, 462: 116-120.
4.
Szaraz, Z., Trojanova, Z., Cabbibo, M. and Evangelista, E. (2007). Strengthening in a WE54 Magnesium Alloy Containing SiC Particles, Materials Science and Engineering A, 462: 225-229.
5.
Towle, D.J. and Friend, C.M. (1993). Comparison of Compressive and Tensile Properties of Magnesium Based Metal Matrix Composites, Materials Science and Technology, 9: 35-41.
6.
Bohlen, J., Dobron, P., Swiostek, J., Letzig, D., Chmelik, F., Lukac, P. and Kainer, K.U. (2007). On the Influence of the Grain Size and Solute Content on the AE Response of Magnesium Alloys Tested in Tension and Compression , Materials Science & Engineering A, 462: 302-306.
7.
Prasad, Y.V.R.K. and Rao, K.P. (2006). Effect of Crystallographic Texture on the Kinetics of Hot Deformation of Rolled Mg-3Al-1Zn Alloy Plate , Materials Science and Engineering A, 432: 170-177.
8.
Jiang, L., Jonas, J.J., Luo, A.A., Sachdev, A.K. and Godet, S. (2007). Influence of {10-12} Extension Twinning on the Flow Behavior of AZ31 Mg Alloy, Materials Science and Engineering A, 445-446: 302-309.
9.
Godet, S., Jiang, L., Luo, A.A. and Jonas, J.J. (2006). Use of Schmid Factors to Select Extension Twin Variants in Extruded Magnesium Alloy Tubes, Scripta Materialia , 55: 1055-1058.
10.
Paramsothy, M., Srikanth, N. and Gupta, M. (2008). Processing, Microstructure and Properties of a Mg/Al Bimetal Macrocomposite, Journal of Composite Materials, in press.
11.
Abbasi, M., Taheri, A.K. and Salehi, M.T. (2001). Growth rate of Intermetallic Compounds in Al/Cu Bimetal Produced by Cold Roll Welding Process, Journal of Alloys and Compounds, 319: 233-241.
12.
Dyja, H., Mroz, S. and Stradomski, Z. (2003). Properties of Joint in the Bimetallic Rods Cu-Al and Cu-steel After Explosive Cladding and the Process of Rolling, Metalurgija, 42: 185-191.
13.
Dyja, H., Mroz, S. and Milenin, A. (2004). Theoretical and Experimental Analysis of the Rolling Process of Bimetallic Rods Cu-Steel and Cu-Al, Journal of Materials Processing Technology, 153-154: 100-107.
14.
Krishna, B.V. , Venugopal, P. and Rao, K.P. (2005). Co-extrusion of Dissimilar Sintered P/M preforms - an Explored Route to Produce Bimetallic Tubes, Materials Science and Engineering A, 407: 77-83.
15.
Krishna, B.V. , Venugopal, P. and Rao, K.P. (2004). Solid State Joining of Dissimilar Sintered P/M Preform Tubes by Simultaneous Cold Extrusion, Materials Science and Engineering A, 386: 301-317.
16.
Jiang, F., Zhao, K. and Sun, J. (2003). Evaluation of Interfacial Crack Growth in Bimaterial Metallic Joints Loaded by Symmetric Three-point Bending, International Journal of Pressure Vessels and Piping, 80: 129-137.
17.
Manesh, H.D. and Taheri, A.K. (2003). Bond Strength and Formability of an Aluminium-clad Steel Sheet, Journal of Alloys and Compounds , 361: 138-143.
18.
Kapinski, S. (1996). Analytical and Experimental Analysis of Deep Drawing Process for Bimetal Elements, Journal of Materials Processing Technology, 60: 197-200.
19.
Marukovich, E.I., Branovitsky, A.M., Na, Y.-S., Lee, J.-H. and Choi, K.-Y. (2006). Study on the Possibility of Continuous-casting of Bimetallic Components in Condition of Direct Connection of Metals in a Liquid State, Materials and Design, 27(10): 1016-1026.
20.
An, J., Liu, Y.B., Zhang, M.Z. and Yang, B. (2002). Effect of Si on the Interfacial Bonding Strength of Al-Pb alloy Strips and Hot-dip Aluminized Steel Sheets by Hot Rolling, Journal of Materials Processing Technology, 120: 30-36.
21.
Mamalis, A.G. , Szalay, A., Vaxevanidis, N.M. and Pantelis, D.I. (1994). Macroscopic and Microscopic Phenomena of Nickel/Titanium `Shape-memory' Bimetallic Strips Fabricated by Explosive Cladding and Rolling, Materials Science and Engineering A, 188: 267-275.
22.
Tham, L.M., Gupta, M. and Cheng, L. (1999). Influence of Processing Parameters During Disintegrated Melt Deposition Processing on Near Net Shape Synthesis of Aluminium Based Metal Matrix Composites, Materials Science and Technology , 15: 1139-1146.
23.
Molina, J.M., Voytovych, R., Louis, E. and Eustathopoulos, N. (2007). The Surface Tension of Liquid Aluminium in High Vacuum: The Role of Surface Condition, International Journal of Adhesion and Adhesives, 27: 394-401.
24.
Shen, P., Nose, M., Fujii, H. and Nogi, K. (2006). Wettability of TiAlN Films by Molten Aluminium , Thin Solid Films, 515(4): 2009-2014.
25.
Tham, L.M., Gupta, M. and Cheng, L. (2001). Effect of Limited Matrix-Reinforcement Interfacial Reaction on Enhancing the Mechanical Properties of Aluminium-Silicon Carbide Composites, Acta Materialia, 49: 3243-3253.
26.
Lloyd, D.J. (1994). Particle Reinforced Aluminium and Magnesium Matrix Composites, International Materials Reviews , 39: 1-23.
27.
Boyer, E.A. (ed.) (1987 ). Fundamentals and Effects of Major Variables, Atlas of Stress-Strain Curves, p. 69, ASM International®, Ohio, USA.
28.
Reed-Hill, R.E. (1964). Physical Metallurgy Principles , 2nd edn, pp. 192, 267, 725, D Van Nostrand Company, New York, USA.
29.
Batra, R.C. and Wei, Z.G. (2007). Instability Strain and Shear Band Spacing in Simple Tensile/Compressive Deformations of Thermoviscoplastic Materials, International Journal of Impact Engineering, 34: 448-463.
30.
Wang, T.S., Hou, R.J., Lv, B., Zhang, M. and Zhang, F.C. (2007). Microstructure Evolution and Deformation Mechanism Change in 0.98C-8.3Mn-0.04N Steel During Compressive Deformation, Materials Science and Engineering A, 465: 68-71.
