Structural Analysis and Strain Monitoring of the Filament Wound Motor Case

Abstract

Filament wound structures such as pressure tanks, pipes and motor cases of rockets are widely used in aerospace applications. The determination of a proper winding angle and thickness is very important to decrease manufacturing difficulties and to increase structural efficiency. In this study, possible winding angles considering the slippage between a fiber and a mandrel surface are calculated using the semi-geodesic path equation. In addition, finite element analyses using ABAQUS are performed to predict the behavior of filament wound structures considering continuous change of the winding angle and thickness at the dome part due to fiber built-up near the metallic boss. Water-pressuring tests of a third stage motor case are performed to verify the analysis procedure. The strain gages are attached on the surface in the fiber direction. Progressive failure analysis predicted the burst pressure a little bit higher than the experiment and the weakest region of the motor case very well. The effect of reinforcement is also studied to increase its performance.

Keywords

filament winding semi-geodesic path equation finite element analysis motor case water-pressuring test

Get full access to this article

View all access options for this article.

References

1. Hartung, R.F. (1963). Planar-Wound Filamentary Pressure Vessels, AIAA Journal, 1: 2842–2844.

2. Denost, J.P. (1982). New Design Concepts for Filament-Wound Pressure Vessel with Unequal Polar Openings. In: Proceedingof the AIAA/SAE/ASME 18th Joint Propulsion Conference.

3. Uemura, M. (1979). Developmental Research on Carbon-Fiber-Reinforced Plastic Rocket Motorcase, The University of Tokyo, Report of Aerospace Research Center, Vol. 15, No. 4.

4. Doh, Y.D. and Hong, C.S. (1995). Progressive Failure Analysis for Filament Wound Pressure Vessel, Journal of Reinforced Plastics and Composites, 14(12): 1278–1306.

5. De Carvalho, J. , Lossie, M. , Vandepitte, D. and Van Brussel, H. (1995). Optimization of Filament-Wound Parts Based on Non-Geodesic Winding, Composites Manufacturing, 6(2): 79–84.

6. Lossie, M. and Van Brussel, H. (1994). Design Principles in Filament Winding, Composites Manufacturing, 5(1): 5–13.

7. Scholliers, J. and Van Brussel, H. (1994). Computer-Integrated Filament Winding: Computer-Integrated Design, Robotic Filament Winding and Robotic Quality Control, Composites Manufacturing, 5(1): 15–23.

8. Jeusette, J.P. , Laschet, G. , Chapentier, P. and Deloo, Ph. (1987). Finite Element Analysis of Composite Revolution structures Wound by Wide plies, Composite Structures, 8: 221–237.

9. James, D.E. and James, A.Y. (April 1987). Graphite Epoxy Pressure Vessel Dome Reinforcement Study, 32nd International SAMPE Symposium.

10.

10. Sun, X.K. , Du, S.Y. and Wang, G.D. (1999). Bursting Problem of Filament Wound Composite Pressure Vessels, International Journal of Pressure Vessels and Piping, 76: 55–59.

11.

11. Kabir, Mohammad Z. (2000). Finite Element Analysis of Composite Pressure Vessels with a Load Sharing Metallic Liner, Composite Structures, 49: 247–255.

12.

12. Hwang, T.K. , Jung, S.K. , Doh, Y.D. , Cho, W.M. and Jung, B. (2000). The Performance Improvement of Filament Wound Composite Pressure Vessels, SAMPE 2000, May 21–25, 1427–1438.

13.

13. Lossie, M. (1990). Production Oriented Design of Filament Wound Composites, Leuven, K.U. PhD Thesis.

14.

14. Reddy, Y.S.N. , Dakshina Moorthy, C.M. and Reddy, J.N. (1995). Non-Linear Progressive Failure Analysis of Laminated Composite Plates, Int. J. Non-Linear Mechanics, 30(5): 629–649.

15.

15. Scholliers, J. (1992). Robotic Filament Winding of Asymmetric Composite Parts, Leuven, K.U. PhD Thesis.