Morphological,thermo-mechanical,and thermal conductivity properties of halloysite nanotube-filled polypropylene nanocomposite foam

Abstract

Studies about polypropylene nanocomposite foams are receiving attention because nanoparticles can change physical and mechanical properties, as well as improve foaming behavior in terms of homogeneous cell structure, cell density, and void fraction. In this research, the foaming behavior of polypropylene, polypropylene/long-chain branched polypropylene (LCBPP) 100/20 blend, and polypropylene/LCBPP/halloysite nanocomposites with 0.5 and 3 parts per hundred of resin (phr) is studied. The LCBPP was used to improve the rheological properties of polypropylene/LCBPP blend, namely the degree of strain-hardening. Transmission electron microscopy observation indicated that halloysite nanotube particles are well distributed in the matrix by aggregates. Subsequent foaming experiments were conducted using chemical blowing agent in injection-molding processing. Polypropylene foam exhibited high cell density and cell size as well as a collapsing effect, whereas the polypropylene/LCBPP blend showed a reduction of the void fraction and cell density compared to expanded polypropylene. Also, the blend showed reduction of the collapsing effect and increase of homogeneous cell size distribution. The introduction of a small amount of halloysite nanotube in the polypropylene/LCBPP blend improved the foaming behavior of the polypropylene, with a uniform cell structure distribution in the resultant foams. In addition, the cell density of the composite sample was higher than the polypropylene/LCBPP sample, having increased 82% and 136% for 0.5 and 3 phr of loaded halloysite nanotube, respectively. Furthermore, the presence of halloysite nanotube increased crystallization temperature (Tc) and slightly increased dynamic-mechanical properties measured by dynamic-mechanical thermal analysis. By increasing halloysite nanotube content to 3 phr, the insulating effect increased by 13% compared to polypropylene/LCBPP blend. For comparative purposes, the effect on foaming behavior of polypropylene/LCBPP was also investigated using talc microparticles.

Keywords

Polypropylene foams halloysite nanoparticles talc microparticles injection-molding nanocomposites foams

Get full access to this article

View all access options for this article.

References

Realinho

Haurie

Antunes

et al.

Thermal stability and fire behaviour of flame retardant high density rigid foams based on hydromagnesite-filled polypropylene composites. Compos Part B 2014; 58: 553–558.

Xiao

Guan

et al.

A novel strategy for the preparation of long chain branching polypropylene and the investigation on foamability and rheology. Eur Polym J 2012; 48: 362–371.

Tabatabaei

Carreau

Ajji

. Rheological and thermal properties of blends of a long-chain branched polypropylene and different linear polypropylenes. Chem Eng Sci 2009; 64: 4719–4731.

Kaewmesri

Lee

Park

et al.

Effects of CO2 and talc contents on foaming behavior of recyclable high-melt-strength PP. J Cell Plast 2006; 42: 405–428.

Forest

Chaumont

Cassagnau

et al.

Polymer nano-foams for insulating applications prepared from CO2 foaming. Prog Polym Sci 2015; 41: 122–145.

Zhang

Tiwary

Parent

et al.

Crystallization and foaming of coagent-modified polypropylene: nucleation effects of cross-linked nanoparticles. Polymer 2013; 54: 4814–4819.

Antunes

Realinho

Velasco

. Study of the influence of the pressure drop rate on the foaming behavior and dynamic-mechanical properties of CO2 dissolution microcellular polypropylene foams. J Cell Plast 2010; 46: 551–571.

Stange

Münstedt

. Effect of long-chain branching on the foaming of polypropylene with azodicarbonamide. J Cell Plast 2006; 42: 445–467.

Zhai

Kuboki

Wang

et al.

Cell structure evolution and the crystallization behavior of polypropylene/clay nanocomposites foams blown in continuous extrusion. Ind Eng Chem Res 2010; 49: 9834–9845.

10.

Chen

Goren

Ozisik

et al.

Controlling bubble density in MWNT/polymer nanocomposite foams by MWNT surface modification. Compos Sci Technol 2012; 72: 190–196.

11.

Ibeh

Bubacz

. Current trends in nanocomposite foams. J Cell Plast 2008; 44: 493–515.

12.

Yeh

J-M

Chang

K-C

Peng

C-W

et al.

Effect of dispersion capability of organoclay on cellular structure and physical properties of PMMA/clay nanocomposite foams. Mater Chem Phys 2009; 115: 744–750.

13.

Hwang

S-S

Hsu

. Effects of silica particle size on the structure and properties of polypropylene/silica composites foams. J Ind Eng Chem 2013; 19: 1377–1383.

14.

Ameli

Jahani

Nofar

et al.

Development of high void fraction polylactide composite foams using injection molding: mechanical and thermal insulation properties. Compos Sci Technol 2014; 90: 88–95.

15.

Yen

Y-C

Lee

Chiu

et al.

Polystyrene foams with inter-connected carbon particulate network. J Cell Plast 2014; 50: 437–448.

16.

Arjmand M, Mahmoodi M, Park S, et al. Impact of foaming on the broadband dielectric properties of multi-walled carbon nanotube/polystyrene composites. J Cell Plast 2014; 50: 551–562.

17.

Lee K, Chang Y-W and Kim SW. Ethylene–propylene–diene terpolymer/halloysite nanocomposites: thermal, mechanical properties, and foam processing. J Appl Polym Sci 2014; 131: 1–8.

18.

Liu

Jia

et al.

Recent advance in research on halloysite nanotubes-polymer nanocomposite. Prog Polym Sci 2014; 39: 1498–1525.

19.

Joussein

Petit

Churchman

et al.

Halloysite clay minerals – a review. Clay Miner 2005; 40: 383–426.

20.

Wang

Huang

H-X

. Incorporation of halloysite nanotubes into PVDF matrix: nucleation of electroactive phase accompany with significant reinforcement and dimensional stability improvement. Compos Part A 2014; 66: 16–24.

21.

Saiz-Arroyo

Saja

Velasco

et al.

Moulded polypropylene foams produced using chemical or physical blowing agents: structure–properties relationship. J Mater Sci 2012; 47: 5680–5692.

22.

Gómez-Gómez

Arencón

Sánchez-Soto

et al.

Influence of the injection-molding parameters on the cellular structure and thermo-mechanical properties of ethylene-propylene block copolymer foams. Adv Polym Technol 2013; 32(S1): E692–E704.

23.

Santos

Castel

Liberman

et al.

Polyolefin-based nanocomposite: the effects of processing aids. J Appl Polym Sci 2011; 119: 1567–1575.

24.

Antunes

Realinho

Velasco

et al.

Thermal conductivity anisotropy in polypropylene foams prepared by supercritical CO2 dissolution. Mater Chem Phys 2012; 136: 268–276.

25.

Ameli

Jung

Park

. Through-plane electrical conductivity of injection-molded polypropylene/carbon-fiber composite foams. Compos Sci Technol 2013; 76: 37–44.

26.

Jahani

Ameli

Jung

et al.

Open-cell cavity-integrated injection-molded acoustic polypropylene foams. Mater Des 2014; 53: 20–28.

27.

Gunkel

Spörrer

ANJ

Lim

et al.

Understanding melt rheology and foamability of polypropylene-based TPO blends. J Cell Plast 2008; 44: 307–325.

28.

Wang

Wan

Qiu

et al.

Effects of long chain branches on the crystallization and foaming behaviors of polypropylene-g-poly(ethylene-co-1-butene) graft copolymers with well-defined molecular structures. Polymer 2012; 53: 4737–4757.

29.

Lee

Zeng

Cao

et al.

Polymer nanocomposite foams. Compos Sci Technol 2005; 65: 2344–2363.

30.

Shen

Zeng

Lee

. Synthesis of polystyrene–carbon nanofibers nanocomposite foams. Polymer 2005; 46: 5218–5224.

31.

Leung

Park

. Effects of nucleating agents' shapes and interfacial properties on cell nucleation. J Cell Plast 2010; 46: 441–460.

32.

Yan L, Zhenhua C and Changchun Z. Poly(methyl methacrylate) (PMMA) nanocomposite foams. New York: CRC Press, 2013, pp.1–34.

33.

Ameli

Nofar

Park

et al.

Polypropylene/carbon nanotube nano/microcellular structures with high dielectric permittivity, low dielectric loss, and low percolation threshold. Carbon 2014; 71: 206–217.

34.

Zheng

Lee

Park

. Use of nanoparticles for improving the foaming behaviors of linear PP. J Appl Polym Sci 2010; 117: 2972–2979.

35.

Ferrage

Martin

Boudet

et al.

Talc as nucleating agent of polypropylene: morphology induced by lamellar particles addition and interface mineral–matrix modelization. J Mater Sci 2002; 37: 1561–1573.

36.

Nofar

Majithiya

Kuboki

et al.

The foamability of low-melt-strength linear polypropylene with nanoclay and coupling agent. J Cell Plast 2012; 48: 271–287.

37.

Velasco

Antunes

Ayyad

et al.

Foaming behaviour and cellular structure of LDPE/hectorite nanocomposites. Polymer 2007; 48: 2098–2108.

38.

Antunes

Velasco

Realinho

et al.

Heat transfer in polypropylene-based foams produced using different foaming processes. Adv Eng Mater 2009; 11: 811–817.

39.

Luo

. Using nanocapsules as building blocks to fabricate organic polymer nanofoam with ultra low thermal conductivity and high mechanical strength. Polymer 2012; 53: 5699–5705.

40.

Gao

Wang

et al.

Preparation and properties of hollow glass bead filled silicone rubber foams with low thermal conductivity. Mater Des 2013; 46: 491–496.

41.

Liang

. Measurement of thermal conductivity of hollow glass-bead-filled polypropylene composites. Polym Test 2006; 25: 527–531.

42.

Bourret

Tessier-Doyen

Naït-Ali

et al.

Effect of the pore volume fraction on the thermal conductivity and mechanical properties of kaolin-based foams. J Eur Ceram Soc 2013; 33: 1487–1495.

43.

Zhao

Thapa

Weiss

et al.

Phase change heat insulation based on wax-clay nanotube composites. Adv Eng Mater 2014; 16: 1391–1399.

44.

Weidenfeller

Höfer

Schilling

. Thermal conductivity, thermal diffusivity, and specific heat capacity of particle filled polypropylene. Compos Part A 2004; 35: 423–429.

45.

Radhakrishnan

Sonawane

. Role of heat transfer and thermal conductivity in the crystallization behavior of polypropylene-containing additives: a phenomenological model. J Appl Polym Sci 2003; 89: 2994–2999.

46.

Forest

Chaumont

Cassagnau

et al.

Polymer nano-foams for insulating applications prepared from CO2 foaming. Prog Polym Sci 2015; 41: 122–145.

47.

Klett

McMillan

Gallego

et al.

The role of structure on the thermal properties of graphitic foams. J Mater Sci 2004; 39: 3659–3676.