Study of the Influence of the Pressure Drop Rate on the Foaming Behavior and Dynamic-Mechanical Properties of CO 2 Dissolution Microcellular Polypropylene Foams
Restricted accessResearch articleFirst published online November, 2010
Study of the Influence of the Pressure Drop Rate on the Foaming Behavior and Dynamic-Mechanical Properties of CO 2 Dissolution Microcellular Polypropylene Foams
This article presents the preparation of microcellular polypropylene foams produced by a CO2 batch-foaming process and their characterization regarding the influence of the pressure drop rate on the foaming behavior and dynamic—mechanical properties. A polypropylene-based material was prepared by melt-mixing in a twin-screw extruder, cooled, and pelletized and later compression-molded in a hot-plate press to solid discs. These discs were finally foamed inside a high pressure vessel by dissolving CO2 and carefully controlling its sudden decompression drop. The dynamic—mechanical properties of the different expansion ratio-produced PP foams were studied, analyzing the influence of the pressure drop rate and residual pressures on the cellular structure and subsequent dynamic—mechanical behavior of the foams. With increasing the sudden pressure drop by reducing the residual pressure value, higher expansion ratio PP foams were obtained, reaching a maximum value of 3. Only slight differences were observed between foams regarding the cell size (maximum cell size ≈ 100 μm), the foams presenting slightly lower specific storage moduli than that of the solid material, indicating the efficiency of this process in nucleating and generating relatively high expansion ratio foams with a closed-cell type of structure and cell sizes in the micrometer range.
Kumar, V.Microcellular Polymers: Novel Materials for the 21st Century, Prog. Rubber Plast. Technol., 1993: 9: 54-70.
2.
Matuana, L.M. , Park, C.B. and Balatinecz , J.J.Structures and Mechanical Properties of Microcellular Foamed Polyvinyl Chloride, Cellular Polym., 1998: 17: 1-16.
3.
Collias, D.I. , Baird, D.G. and Borggreve , R.J.M.Impact Toughening of Polycarbonate by Microcellular Foaming, Polymer, 1994: 35: 3978-3983.
4.
Barlow, C., Kumar, V., Flinn, B., Bordia, R.K. and Weller, J. ( 2001). Impact Strength of High Density Microcellular Polycarbonate Foams, J. Eng. Mater.Technol., 123: 229-233.
5.
Kumar, V. and Weller, J.E.A Process to Produce Microcellular PVC, Internat. Polym. Process. , 1993: 7: 73-80.
6.
Kumar, V., Vander Wel, M., Weller, J.E. and Seeler, K.A.Experimental Characterization of the Tensile Behavior of Microcellular Polycarbonate Foams, J. Eng. Mater. Technol., 1994: 116: 439-445.
Colton, J. and Suh, N.P.The Nucleation of Microcellular Thermoplastic Foam with Additives: Part I: Theoretical Considerations, Polym. Eng. Sci., 1987: 27: 485-492.
9.
Kumar, V. ( 1988). Process Synthesis for Making Microcellular Thermoplastic Parts: A Case Study in Axiomatic Design, PhD Thesis, Department of Mechanical Engineering, MIT, USA.
10.
Kweeder, J.A. , Ramesh, N.S., Campbell, G.A. and Rasmussen , D.H. (1991). The Nucleation of Microcellular Polystyrene Foam, SPE Technical Papers, Montreal, Canada, Vol. 37, p. 1398.
11.
Jiang, X.-L. , Liu, T., Zhao, L., Xu, Z.-M. and Yuan, W.-K.Effects of Blend Morphology on the Foaming of Polypropylene/Low-density Polyethylene Blends During a Batch Foaming Process , J. Cellul. Plast., 2009: 45: 225- 241.
12.
Wu, Q., Park, C.B., Zhou, N. and Zhu, W.Effect of Temperature on Foaming Behaviors of Homo- and Co-polymer Polypropylene/Polydimethylsiloxane Blends with CO2, J. Cellul. Plast., 2009: 45: 303-319.
13.
Park, C.B. and Cheung, L.K.A Study of Cell Nucleation in the Extrusion of Polypropylene Foams, Polym. Eng. Sci., 1997: 37: 1-17.
14.
Nojiri, A., Sawasaki, T. and Koreeda, T. ( 1984). Crosslinkable Polypropylene Composition, U.S. Patent4,424,293.
15.
Nojiri, A., Sawasaki, T., Konishi, T., Kudo, S. and Onobori, S.Crosslinking of Polypropylene and Application to Foaming, Furukawa Revi., 1982: 2: 34.
16.
Lee, Y.D. and Wang, L.F.Properties of Polypropylene Structural Foam Crosslinked by Vinyltrimethoxy Silane, J. Appl. Polym. Sci. , 1986: 32: 4639-4647.
17.
Kitagawa, S., Nakayama, T. and Isono, M. ( 1987). Process for Producing Polypropylene Foam, U.S. Patent4,766,159.
18.
Park, J.J., Katz, L. and Gaylord, N.G. ( 1992). Polypropylene Foam Sheets, U.S. Patent5,149,579.
19.
Park, J.J., Katz, L. and Gaylord, N.G. ( 1991). Polypropylene Foam Sheets, U.S. Patent5,116,881.
20.
Philips, E.M. , McHugh, K.E. and Bradley, M.B.Polypropylen mit hoher Schmelzestabilität , Kunststoffe, 1992: 82: 671-676.
21.
Stange, J. and Münstedt, H.Rheological Properties and Foaming Behavior of Polypropylenes with Different Molecular Structures, J. Rheol., 2006: 50: 907-923.
22.
Antunes, M. , Velasco, J.I., Realinho, V. and Solórzano , E.Study of the Cellular Structure Heterogeneity and Anisotropy of Polypropylene and Polypropylene Nanocomposite Foams, Polym. Eng. Sci., 2009: 49: 2400-2413.
23.
Park, C.B., Cheung, L.K. and Song, S.-W.The Effect of Talc on Cell Nucleation in Extrusion Foam Processing of Polypropylenes with CO2 and Isopentane, Cellular Polym., 1998: 17: 221-251.
24.
Naguib, H.E. , Xu, J.X., Park, C.B., Hesse, A., Panzer, U. and Reichelt, N. (2001). Effects of Blending of Branched and Linear Polypropylene Resins on Foaming, SPE, ANTEC, Technical Papers, Vol. 47, pp. 1623-1630.
25.
Naguib, H.E. , Park, C.B., Wang, J., Mukhopadhyay, A.K. and Reichelt, N.Effect of Recycling on the Rheological Properties and Foaming Behaviors of Branched PP, Cellular Polym., 2003: 22: 1-22.
26.
Schumacher, H. , Michaeli, W. and Lorenz, J. (2004). Assessment of the Foamability of Polymers on the Basis of their Biaxial Stress/Strain Behaviour, In: Conference Proceedings of the Sixth International Conference Blowing Agents and Foaming Processes, Rapra Technology , Hamburg, pp. 137-146.
27.
Kaewmesri, W., Lee, P.C., Park, C.B. and Pumchusak , J.Effects of CO2 and Talc Contents on Foaming Behavior of Recyclable High-melt-strength PP, J. Cellular Plast., 2006: 42: 405-428.
28.
Cheung, L.K. , Park, C.B. and Behravesh , A.H. (1996). Effect of Branched-Structure on the Cell Morphology of Extruded Polypropylene Foams. 1. Cell Nucleation, ANTEC’96 Technical Papers , Vol. 42, pp. 1941-1947.
29.
Nam, P.M. , Okamoto, M., Kotaka, T., Nakayama, T., Takada, M., Ohshima, M. et al. Foam Processing and Cellular Structure of Polypropylene/Clay Nanocomposites, Polym. Eng. Sci., 2002: 42: 1907-1918.
30.
Bhattacharya, S., Gupta, R.K., Jollands, M. and Bhattacharya , S.N.Foaming Behavior of High-melt Strength Polypropylene/Clay Nanocomposites, Polym. Eng. Sci., 2009: 49: 2070-2084.
Stange, J., Uhl, C. and Münstedt, H.Rheological Behavior of Blends from a Linear and a Long-Chain Branched Polypropylene , J. Rheol., 2005: 49: 1059-1079.
33.
Spitael, P. and Macosko, C.W. ( 2004). Strain Hardening in Polypropylene and its Role in Extrusion Foaming, Polym. Eng. Sci., 44: 2090-2100.
34.
Almanza, O., Rodríguez-Pérez, M.A. and de Saja, J.A.The Microstructure of Polyethylene Foams Produced by a Nitrogen Solution Process, Polymer, 2001: 42: 7117-7126.
35.
Martini, J.E. , Suh, N.P. and Waldman, F.A. (1984). Microcellular Closed Cell Foams and Their Method of Manufacture, U.S. Patent4,473,665.
36.
UK Zotefoams (1999). New PP Foam Delivers 100% PP Performance, High Performance Polymers, In: Humphreys, S. (ed.), Rapra Review Reports (2003), UK, Item163, pp. 62-63.
37.
Zhang, Z. and Handa, Y.P.An In Situ Study of Plasticization of Polymers by High-pressure Gases, J. Polym. Sci. Polym. Phys., 1998: 36: 977-982.
38.
Eaves, D. ( 2004). Handbook of Polymer Foams, Shawbury, UK, Rapra Technology Limited, p. 189.
39.
Goel, S.K. and Beckman, E.J.Generation of Microcellular Polymers using Supercritical CO2, Cellular Polym., 1993: 12: 251-274.
40.
Arora, K.A. , Lessor, A.J. and McCarthy, T.J.Preparation and Characterization of Microcellular Polystyrene Foams Processed in Supercritical Carbon Dioxide, Macromolecules, 1998: 31: 4614-4620.
41.
Cooper, A.Synthesis and Processing of Polymers using Supercritical Carbon Dioxide, J. Mater. Chem., 2000: 10: 207-234.
Doroudiani, S., Park, C.B. and Kortschot , M.T.Effect of the Crystallinity and Morphology on the Microcellular Foam Structure of Semicrystalline Polymers , Polym. Eng. Sci., 1996: 36: 2645-2662.
44.
Huang, H.-X. and Wang, J.-K.Improving Polypropylene Microcellular Foaming Through Blending and the Addition of Nano-Calcium Carbonate, J. Appl. Polym. Sci., 2007: 106: 505-513.
45.
Doroudiani, S., Park, C.B. and Kortschot , M.T.Processing and Characterization of Microcellular Foamed High-density Polyethylene/ Isotactic Polypropylene Blends, Polym. Eng. Sci., 1998: 38: 1205-1215.
46.
Rachtanapun, P., Selke, S.E.M. and Matuana , L.M.Microcellular Foam of Polymer Blends of HDPE/PP and their Composites with Wood Fiber, J. Appl. Polym. Sci., 2003: 88: 2842-2850.
47.
Rachtanapun, P., Selke, S.E.M. and Matuana , L.M.Effect of High-density Polyethylene Melt Index on Microcellular Foaming of High-density Polyethylene/Polypropylene Blends, J. Appl. Polym. Sci., 2004: 93: 364-371.
48.
Okamoto, M. , Nam, P.H., Maiti, P., Kotaka, T., Nakayama, T., Takada, M. et al. Biaxial Flow-Induced Alignment of Silicate Layers in Polypropylene/ Clay Nanocomposite Foam, Nano Lett. , 2001: 1: 503-505.
49.
Taki, K., Yanagimoto, T., Funami, E. and Ohshima, M.Visual Observation of CO2 Foaming of Polypropylene-Clay Nanocomposites, Polym. Eng.Sci., 2004: 44: 1004-1011.
50.
Antunes, M., Velasco, J.I., Realinho, V., Martínez, A.B., Rodríguez-Pérez, M.A. and de Saja, J.A.Heat Transfer in Polypropylene-based Foams Produced Using Different Foaming Processes, Adv. Eng. Mater. , 2009: 11: 811-817.
51.
Sims, G.L.A. and Khunniteekool, C.Cell Size Measurement of Polymeric Foams, Cellular Polym. , 1994: 13: 137-146.
52.
Wunderlich, B. ( 1990). Thermal Analysis, New York, Academic Press.
53.
Antunes, M., Velasco, J.I., Realinho, V. and Arencón, D.Characterization of Carbon Nanofibre-Reinforced Polypropylene Foams, J. Nanosci. Nanotechnol., 2010: 10: 1241-1250.
54.
Rodríguez-Pérez, M.A., Duijsens, A. and de Saja, J.A.Effect of Addition of EVA on the Technical Properties of Extruded Foam Profiles of Low Density Polyethylene/EVA Blends , J. Appl. Polym. Sci., 1998: 68: 1237-1244.
55.
Almanza, O. , Rodríguez-Pérez , M.A. and de Saja, J.A.The Prediction of the Radiation Term in the Thermal Conductivity of Crosslinked Closed Cell Polyolefin Foams, J. Polym. Sci. Polym. Phys., 2000: 38: 993-1004.
56.
Gibson, L.J. and Ashby, M.F. ( 1998). Cellular Solids: Structure and Properties, 2nd edn, Oxford, Pergamon Press.
57.
Okamoto, K.T. (2003). Microcellular Processing , Munich, Carl Hanser Verlag.
