An in situ modification method is used to synthesize a new type of phenolic resin-based composite material used to fill goafs and seal air leaks in roadways. This was followed by scanning electron microscopy, oxygen index, and compression tests. The results show that when the aluminium hydroxide, Sd-31 silicone oil and methylene chloride are added to the phenolic resin in a mass fraction ratio of 8%:5%:3%, the overall performance of the composite material is the best. Compared with unmodified phenolic resin, the oxygen index and compressive strength of thecomposite material are increased by 40.16% and 3.5 times, respectively. The maximum reaction temperature of foaming and curing is also reduced from 120.3 to 87.2°C. To verify the performance of the new material, field tests were carried out at Matigou coal mine in Gansu, China. The average air leakage rate of the working face was reduced from 12.8 to 2.1 %.
Bohlin-NizzettoP, MelymukL, WhiteKB, KalinaJ, MadadiVO, Adu-KumiS, ProkešR, PribylovaP, KlanovaJ.2020. Field- and model-based calibration of polyurethane foam passive air samplers in different climate regions highlights differences in sampler uptake performance. Atmos Environ. DOI: 10.1016/j.atmosenv.2020.117742.
3.
DengP, ShiY, LiuY, WangQ.2018. Solidifying process and flame retardancy of epoxy resin cured with boron-containing phenolic resin. Appl Surf Sci. 427: 894 – 904.
4.
DingHY, WangJF, LiuJ, XuY, ChenR, WangC, ChuF.2015. Preparation and properties of a novel flame retardant polyurethane quasi-prepolymer for toughening phenolic foam. J Appl Polym Sci. 132 (35): 42424.
5.
GbadamosiAR, OnifadeM, GencB, RupprechtS.2020. Analysis of spontaneous combustion liability indices and coal recording standards/basis. Int J Min Sci Technol. 30 (5): 723 – 736.
6.
GeTJ, HuXQ, WangDQ.2020. Modification and properties of phenolic resin based wear-resistant composite. Plastics. 49 (2): 69 – 72 + 84.
7.
GeTJ, TangKH, YuY, TanXP.2018. Preparation and properties of the 3-pentadecyl-phenol in situ modified foamable phenolic resin. Polymers. 347 (9): 33 – 38.
KennyJM, PisanielloG, FarinaF, PuzzielloS.1995. Calorimetric analysis of the polymerization reaction of a phenolic resin. Thermochim Acta. 269–270: 201 – 211.
10.
LiJL, NiuYH, LuY.2019. Study on effect of wind speed to air leakage and spontaneous combustion in goaf of contiguous seams. Coal Sci Technol. 47 (3): 156 – 162.
11.
LiangHJ, WangL, ZhaoZY.2017. Study on application of high water quick-setting material in support of broken rock roadway. Coal Technol. 36 (7): 37 – 39.
12.
LiangJZ, ZhuB.2016. Estimation of sound transmission loss of polymer/hollow microsphere composites. J Compos Mater. 50 (15): 2137 – 2142.
LuX, QuJ, HuangJ.2015. Mechanical, thermal and rheological properties of hollow glass microsphere filled thermoplastic polyurethane composites blended by normal vane extruder. Plast Rubber Compos. 44 (8): 306 – 313.
15.
OnifadeM, GencB.2020. A review of research on spontaneous combustion of coal. Int J Min Sci Technol. 30 (3): 303 – 311.
16.
OnifadeM, GencB, BadaS.2020. Spontaneous combustion liability between coal seams: a thermogravimetric study. Int J Min Sci Technol. 30 (5): 691 – 698.
17.
PengC, FujunH, YueF.2016. Performance of water-based foams affected by chemical inhibitors to retard spontaneous combustion of coal. Int J Min Sci Technol. 26 (3): 443 – 448.
18.
QinBT, WangDM, ChenJH, LiangXY.2005. Experimental investigation of high-performance three-phase foam for mine fire control. J China Univ Min Technol. 34 (1): 11 – 15.
19.
SaidKO, OnifadeM, LawalAI, GithiriaJM.2020. Computational intelligence-based models for predicting the spontaneous combustion liability of coal. Int J Coal Prep Util. DOI: 10.1080/19392699.2020.1741558.
20.
ShiYB, YangLL, XuTF.2020. Comprehensive mine fire prevention technology and its application. Energy Technol Manag. 45 (4): 140 – 142.
21.
SmithAC, MironY, LazzaraC. P.1988. Inhibition of spontaneous combustion of coal, report of investigation. U.S. Bureau of Mines.
22.
VanajaA, RaoR.2002. Synthesis and characterisation of epoxy–novolac/bismaleimide networks. Eur Polym J. 38 (1): 187 – 193.
23.
WangJ, JiangN, JiangH.2010. Micro-structural evolution of phenol-formaldehyde resin modified by boron carbide at elevated temperatures. Mater Chem Phys. 120 (1): 187 – 192.
24.
WangK, TangHB, WangFQ, MiaoY, LiuD.2019. Research on complex air leakage method to prevent coal spontaneous combustion in longwall goaf. PLoS One. 14 (3): e0213101.
25.
WuWL, WangJ.2018. Effect of KH550 on the preparation and compatibility of carbon fibers reinforced silicone rubber composites. Silicon. 10 (5): 1903 – 1910.
26.
XuWH, QinXM, LiuZG.2019. Study on flame retardancy and thermal properties of phenol formaldehyde resin-based wood-plastic composites. Plast Sci Technol. 47 (1): 43 – 47.
27.
XuYL, WangDM, ZhongXX, TlanZJ, XYQi. 2009. Study of inhibition characteristic of sand suspending thickener for spontaneous combustion prevention. Procedia Earth Planet Sci. 1 (1): 336 – 340.
28.
YesgatAL, KiteyR.2016. Effect of filler geometry on fracture mechanisms in glass particle filled epoxy composites. Eng Fract Mech. 160: 22 – 41.
29.
YiTH.2001. Modification development of phenolic resin. Thermosetting Resin. 16 (4): 29 – 33.
30.
YunJ, ChenLX, ZhangXF, ZhaoH, WenZ, ZhuD.2018. Synthesis and structure evolution of phenolic resin/silicone hybrid composites with improved thermal stability. J Mater Sci. 53 (20): 14185 – 14203.
31.
YunMS, LeeWI.2008. Analysis of bubble nucleation and growth in the pultrusion process of phenolic foam composites. Compos Sci Technol. 68 (1): 202 – 208.
32.
ZhangDS, FanGW, MaLQ, WangA, LiuYD.2009. Harmony of large-scale underground mining and surface ecological environment protection in desert district – a case study in Shendong mining area, Northwest of China. Procedia Earth Planet Sci. 1 (1): 1114 – 1120.
