In this study wet grinding batch experiments were performed in a laboratory ball mill using laterites from Evia island, Greece, in order to determine the optimal grinding conditions for potential nickel upgrade. Selective grinding which exploits the different grindability between soft and hard minerals was considered. Kinetic models were determined based on population balance considerations for different feed and ball sizes. The efficiency of selective grinding was evaluated by taking into account breakage kinetics as well as the grade and recovery of nickel in the products. The results showed that, in general, nickel tends to concentrate in the finer fraction of −0.075 mm. In this fraction nickel recovery is increased significantly with increasing grinding times, while only a slight decrease in its grade is noticed. The results of breakage rate analysis indicate that nickel bearing phases are ground with a higher rate when shorter grinding times are used.
AlevizosG.1997. Mineralogy, geochemistry and genesis of the sedimentary nickeliferous iron-ores of Locris (central Greece) [dissertation]. Chania: Technical University of Crete (in Greek).
2.
AntibachiD, KelepertzisE, KelepertsisA.2012. Heavy metals in agricultural soils of the Mouriki-Thiva area (central Greece) and environmental impact implications. Soil Sediment Contam. 21:434–450. doi: 10.1080/15320383.2012.672493
3.
AustinLG, BaggaP.1981. An analysis of fine dry grinding in ball mills. Powder Technol.28:83–90. doi: 10.1016/0032-5910(81)87014-3
4.
AustinLG, BaggaP, CelikM.1981. Breakage properties of some materials in a laboratory ball mill. Powder Technol. 28:235–243. doi: 10.1016/0032-5910(81)87049-0
5.
AustinLG, KlimpelRR, LuckiePT.1984. Process engineering of size reduction: ball milling. New York, NY: SME – AIME.
6.
AustinLG, LuckiePT.1972. Methods for determination of breakage distribution parameters. Powder Technol. 5:215–222. doi: 10.1016/0032-5910(72)80022-6
7.
BilgiliE.2007. On the consequences of non-first-order breakage kinetics in comminution processes: absence of self-similar size spectra. Part Part Syst Charact. 24:12–17. doi: 10.1002/ppsc.200601043
8.
BilgiliE, ScarlettB.2005. Population balance modeling of non-linear effects in milling processes. Powder Technol. 153:59–71. doi: 10.1016/j.powtec.2005.02.005
9.
CarvalhoRM, TavaresM.2013. Predicting the effect of operating and design variables on breakage rates using the mechanistic ball mill model. Miner Eng. 43–44:91–101. doi: 10.1016/j.mineng.2012.09.008
10.
DanhaG, HildebrandtD, GlasserD, BhondayiC.2015. Application of basic process modeling in investigating the breakage behavior of UG2 ore in wet milling. Powder Technol. 279:42–48. doi: 10.1016/j.powtec.2015.03.034
11.
DenizV.2003. A study on the specific rate of breakage of cement materials in a laboratory ball mill. Cement Concreate Res. 33:439–445. doi: 10.1016/S0008-8846(02)00976-6
12.
DenizV.2012a. A study of effect of ball diameter on breakage properties of clinker and limestone. Indian J Chem Technol. 19:180–184.
13.
DenizV.2012b. The effects of ball filling and ball diameter on kinetic breakage parameters of barite powder. Adv Powder Technol. 23:640–646. doi: 10.1016/j.apt.2011.07.006
14.
Economou-EliopoulosM, FreiR, MegremiI.2016. Potential leaching of Cr(VI) from laterite mines and residues of metallurgical products (red mud and slag): An integrated approach. J Geochem Explor. 162:40–49. doi: 10.1016/j.gexplo.2015.12.007
15.
ErdemAS, ErgünSL.2009. The effect of ball size on breakage rate parameter in a pilot scale ball mill. Miner Eng. 22:660–664. doi: 10.1016/j.mineng.2009.01.015
16.
ErdemoǧluM, SarikayaM.2002. The effect of grinding on pyrophyllite flotation. Miner Eng. 15(10):723–725. doi: 10.1016/S0892-6875(02)00210-8
17.
FarrokhpayS, FornasieroD, FilippovL.2018. Upgrading nickel in laterite ores by flotation. Miner Eng. 121:100–106. doi: 10.1016/j.mineng.2018.02.021
18.
FreemanWA, NewellR, QuastKB.2000. Effect of grinding media and NaHS on copper recovery at Northparkes mines. Miner Eng. 13:1395–1403. doi: 10.1016/S0892-6875(00)00121-7
19.
FuerstenauDW, AbouzeidA-ZM.1991. Effect of fine particles on the kinetics and energetics of grinding coarse particles. Int J Miner Process. 31:151–162. doi: 10.1016/0301-7516(91)90024-D
20.
FuerstenauDW, PhatakPB, KapurPC, AbouzeidA-ZM.2011. Simulation of the grinding of coarse/fine (heterogeneous) systems in a ball mill. Int J Miner Process. 99:32–38. doi: 10.1016/j.minpro.2011.02.003
21.
GonçalvesKLC, AndradeVLL, PeresAEC.2003. The effect of grinding conditions on the flotation of a sulphide copper ore. Miner Eng. 16:1213–1216. doi: 10.1016/j.mineng.2003.05.006
22.
GuptaVK, SharmaS.2014. Analysis of ball mill grinding operation using mill power specific kinetic parameters. Adv Powder Technol. 25:625–634. doi: 10.1016/j.apt.2013.10.003
23.
HanY, ZhuY, WangZ, TianY.2010. Effects of DA as a grinding aid on selective grinding of low-grade bauxite. In: International Mineral Processing Congress (IMPC); Sept 6–10; Australia. Brisbane: Australasian Institute of Mining and Metallurgy. p. 781–789.
24.
HerbstJA, FuerstenauDW.1980. Scale-up procedure for continuous grinding mill design using population balance models. Int J Miner Process. 7:1–31. doi: 10.1016/0301-7516(80)90034-4
IpekH, GöktepeF.2011. Determination of grindability characteristics of zeolite. Physicochem Probl Miner Process. 47:183–192.
27.
KatubilwaFM, MoysMH.2009. Effect of ball size distribution on milling rate. Miner Eng. 22:1283–1288. doi: 10.1016/j.mineng.2009.07.008
28.
KatubilwaFM, MoysMH, GlasserD, HildebrandtD.2011. An attainable region analysis of the effect of ball size on milling. Powder Technol. 210:36–46. doi: 10.1016/j.powtec.2011.02.009
29.
KimJ, DodbibaG, TannoH, OkayaK, MatsuoS, FujitaT.2010. Calcination of low-grade laterite for concentration of Ni by magnetic separation. Miner Eng. 23:282–288. doi: 10.1016/j.mineng.2010.01.005
30.
KlimpelRR, AustinLG.1977. The back-calculation of specific rates of breakage and non-normalized breakage distribution parameters from batch grinding data. Int J Miner Process. 4:7–32. doi: 10.1016/0301-7516(77)90028-X
31.
KotakeN, DaiboK, YamamotoT, KandaY.2004. Experimental investigation on a grinding rate constant of solid materials by a ball mill—effect of ball diameter and feed size. Powder Technol. 143–144:196–203. doi: 10.1016/j.powtec.2004.04.014
32.
McDonaldRG, WhittingtonBI.2008. Atmospheric acid leaching of nickel laterites review part I. Sulphuric acid technologies. Hydrometallurgy. 91:35–55. doi: 10.1016/j.hydromet.2007.11.009
33.
MulengaFK, MoysMH.2014. Effects of slurry pool volume on milling efficiency. Powder Technol. 256:428–435. doi: 10.1016/j.powtec.2014.02.013
34.
NosratiA, QuastK, XuD, SkinnerW, RobinsonDJ, Addai-MensahJ.2014. Agglomeration and column leaching behaviour of nickel laterite ores: effect of ore mineralogy and particle size distribution. Hydrometallurgy. 146:29–39. doi: 10.1016/j.hydromet.2014.03.004
35.
OlejnikTP.2013. Selected mineral materials grinding rate and its effect on product granulometric composition. Physicochem Probl Mi. 49:407–418.
36.
OuLM, FengQM, ZhangGF, ChenY.2008. Comminution property of bauxite and selective separation of Al and Si in bauxite. Miner Process Extr Metall. 117(3):179–184. doi: 10.1179/174328508X283487
37.
PetrakisE, KomnitsasK.2017. Improved modeling of the grinding process through the combined use of matrix and population balance models. Minerals. 7(5):67. doi: 10.3390/min7050067
38.
PetrakisE, StamboliadisE, KomnitsasK.2017. Identification of optimal mill operating parameters during grinding of quartz with the use of population balance modeling. KONA Powder Part J. 34:213–223. doi: 10.14356/kona.2017007
39.
QianHY, KongQG, ZhangBL.2013. The effects of grinding media shapes on the grinding kinetics of cement clinker in ball mill. Powder Technol. 235:422–425. doi: 10.1016/j.powtec.2012.10.057
40.
QuastK, ConnorJN, SkinnerW, RobinsonDJ, Addai-MensahJ.2015. Preconcentration strategies in the processing of nickel laterite ores part 1: literature review. Miner Eng. 79:261–268. doi: 10.1016/j.mineng.2015.03.017
41.
RajamaniRK, GuoD.1992. Acceleration and deceleration of breakage rates in wet ball mills. Int J Miner Process. 34:103–118. doi: 10.1016/0301-7516(92)90018-R
42.
RiceNM.2016. A hydrochloric acid process for nickeliferous laterites. Miner Eng. 88:28–52. doi: 10.1016/j.mineng.2015.09.017
43.
SakaroglouM, AnastassakisG.2017. Nickel recovery from electric arc furnace slag by magnetic separation. J Min Metall. 53A:3–15. doi: 10.5937/JMMA1701003S
44.
ShinH, LeeS, JungHS, KimJ-B.2013. Effect of ball size and powder loading on the milling efficiency of a laboratory-scale wet ball mill. Ceram Int. 39:8963–8968. doi: 10.1016/j.ceramint.2013.04.093
UmucuY, AltınigneMY, DenizV.2014. The effects of ball types on breakage parameters of barite. J Pol Miner Eng Soc. 15:113–117.
47.
WangZ, ChuM, LiuZ, WangH, ZhaoW, GaoL.2017. Preparing Ferro-Nickel Alloy from low-grade Laterite Nickel Ore based on metallized reduction–magnetic separation. Metals (Basel). 7:313. doi: 10.3390/met7080313
48.
YusupovTS, KirillovaEA, DenisovGA.2003. Dressing of Quartz-Feldspar Ores on the basis of selective grinding and mechanical activation. J Min Sci. 39:174–177. doi: 10.1023/B:JOMI.0000008464.34124.1d
49.
ZevgolisE, ZografidisC, HalikiaI.2010. The reducibility of the Greek nickeliferous laterites: a review. Miner Process Extr Metall. 119(1):9–17. doi: 10.1179/174328509X431472
