The characteristics of iron ore fines were considered to have tremendous effects on their subsequent sintering performances, but it is difficult to judge their sintering performances only based on their basic physicphysio-chemical properties. In this study, the correlation between the fundamental high temperature properties of seven commercial Australian iron ore fines and their single-ore sintering performance were revealed by measuring the lowest assimilation temperature (LAT), index of fluidity of liquid phase (IFL), strength of bonding phases (SBP) and the percentage of formed silicoferrite of calcium and aluminium (SFCA) of the iron ores and conducting pilot scale sintering pot tests. The results showed that the correlation is very complicated. There is a negative correlation between the tumble index (TI) of sinter products and LAT of iron ore fines. Iron ore fines have better sintering performance within the appropriate range of IFL between 0.17 and 0.88. The correlativity between SBP, percentage of formed SFCA (PFS) and the sintering performance of iron ore fines is complex.
DawsonPR, OstwaldJ, HayesKM.1985. Influence of alumina on development of complex calcium ferrites in iron ore sinters. Trans. Inst. Min. Metall. (Sect.C: Mineral Process. Extra. Metall. 94(6):71–78.
2.
GalvinKP, RobertsA, LooCE, EvansGM, WilliamsK, IvesonSM.2015. Australian research council research hub for advanced technologies for Australian iron ore - an introduction. Paper presented at: iron ore conference 2015. Iron ore conference 2015; Jul 13–15; Perth, Australia.
3.
GuoL-F, LiuX-M, YouX-Q.2012. The effect of the fundamental high temperature properties of iron ores on the strength of sinters. Paper presented at: collected papers of the ironmaking technology in hebei province in 2012 and academic annual meeting. Proceedings of the ironmaking technology in hebei province in 2012 and academic annual meeting; Sep 14–15; Shijiazhuang; China. Chinese.
4.
HidaY, NosakaN.1992. Iron ore deposits and future properties of iron ore products in western Australia. Tetsu to Hagane. 78(7):960–968. doi: 10.2355/tetsutohagane1955.78.7_960
5.
KamisakaE, SomaH, TakadaT.1984. High temperature properties of calcium ferrite. Trans. ISIJ. 24(2):B-42.
6.
KasaiE, OmoriY.1993. Subjects on the evaluation of process and products in the sintering of iron ore. Tetsu to Hagane. 79(11):1217–1223. doi: 10.2355/tetsutohagane1955.79.11_1217
7.
KasaiE, WuS-L, OmoriY.1991. Influence of property of iron ores on the coalescing phenomenon of granules during sintering. Tetsu to Hagane. 77(1):56–62. doi: 10.2355/tetsutohagane1955.77.1_56
8.
KhosaJ, ManuelJ.2007. Predicting granulating behaviour of iron ores based on size distribution and composition. ISIJ Int. 47(7):965–972. doi: 10.2355/isijinternational.47.965
9.
LuL, HolmesRJ, ManuelJR.2007. Effect of alumina on sinter performance of hematite iron ores. ISIJ Int. 47(7):349–358. doi: 10.2355/isijinternational.47.349
10.
LuL, IshiyamaO.2015. Recent advances in iron ore sintering. Iron ore conference 2015; Jul 13–15; Perth, Australia.
11.
MachidaS, NushiroK, IchikawaK.2005. Experimental evaluation of chemical composition and viscosity of melts. ISIJ Int. 45(4):513–521. doi: 10.2355/isijinternational.45.513
12.
MatsumuraM, HoshiM, KawaguchiT.2005. Improve of sinter softening property and reducibility by controlling chemical compositions. ISIJ Int. 45(4):594–602. doi: 10.2355/isijinternational.45.594
13.
OoiTC, Campbell-HardwickS, ZhuD-Q, PanJ.2014. Sintering performance of magnetite-hematite-goethite and hematite-goethite iron ore blends and microstructure of products of sintering. Min Proc Ext Met Rev. 35(4):266–281. doi: 10.1080/08827508.2013.793681
14.
ScarlettNVY, PowncebyMI, MadsenIC, ChristensenA.2004. Reaction sequences in the formation of silico-ferrites of calcium and aluminum in iron ore sinter. Metall Mater Trans B. 35(5):929–936. doi: 10.1007/s11663-004-0087-4
15.
ShenH-G, DuJ-X, WuS-L.2005. The experimental study on iron ore sintering basic characteristics. Paper presented at: collected papers of the 4th metallurgical engineering science forum. Proceedings of the 4th metallurgical engineering science forum; Apr 1–2; Beijing, China. Chinese.
16.
ShigakiI, SawadaM, GennaiN.1986. Increase in low temperature reductuion of iron ore sinter due to hematite-alumina solid solution and columnar calcium ferrite. Trans. Iron Steel Inst. Jpn. 26(6):503–511. doi: 10.2355/isijinternational1966.26.503
17.
VenkataramanaR, GuptaSS, KapurPC.1999. A combined model for granule distribution and cold bed permeability in the wet stage of iron ore sintering process. Int. J. Miner Process. 57:43–58. doi: 10.1016/S0301-7516(99)00005-8
18.
WuS-L, DaiY-M, DauterO.2010. Optimization of ore blending during sintering based on complementation of high properties. J Univ Sci Technol B. 32(6):719–724. Chinese.
19.
WuS-L, LiuY, DuJ-X.2002. New concepts of the fundamental high temperature properties of iron ores. J Univ Sci Technol B. 24(3):254–257. Chinese.
20.
WuS-L, WangJ, DuJ-X.2003. Basic study on formation character of SFCA of iron fines. Paper presented at: collected papers of the 2th metallurgical engineering science forum. Proceedings of the 2th metallurgical engineering science forum; Apr 1-2; Beijing, China. Chinese.
21.
WuS-L, ZhangG-L, ChenS-G, SuB.2014. Influencing factors and effects of assimilation characteristic of iron ores in sintering process. ISIJ Int. 54(3):582–588. doi: 10.2355/isijinternational.54.582
22.
YanL-J, WuS-L, YouY.2010. Assimilation of iron ores and ore matching method based on complementary assimilation. J Univ Niv Sci Technol B. 32(3):298–305. Chinese.
23.
YangL-X, DavisL.1999. Assimilation and mineral formation during sintering for blends containing magnetite concentrate and hematite/pisolite sintering fines. ISIJ Int. 39(3):239–245. doi: 10.2355/isijinternational.39.239
24.
ZhouM, JiangT, YangS-T, XueX-X.2015. Vanadium-titanium magnetite ore blend optimization for sinter strength based on iron ore basic sintering characteristics. Int J Miner Process. 142:125–133. doi: 10.1016/j.minpro.2015.04.019
