The tribological properties such as ‘specific wear rate’ and ‘coefficient of friction’ (COF) of a new high entropy alloy (HEA) of (Al)10(FeCoNiCu)90 were determined by sliding against the normal loads of 30 and 40 N and compared with that of the high-speed steel (HSS) in this work. The major wear mechanism in the HEA was ploughing due to abrasion. The specific wear rate determined for the HEA at 40 N load is slightly higher (∼7%) than that at 30 N load indicating small increase in wear rate on significant increase in the load. The specific wear rate of the HEA is about five times higher than that of HSS at 30 N load. At 30 N load, after 200 m of sliding, both the wear volume rate and COF decreased continuously for the HEA on increasing the sliding distance due to the presence of sufficient amount of lubricating wear debris.
GuoS, LiuCT.Phase stability in high entropy alloys: formation of solid-solution phase or amorphous phase. Prog Nat Sci Mater Int. 2011;21:433–446. DOI:10.1016/S1002-0071(12)60080-X
6.
ChenC, PangS, ChengY, . Microstructure and mechanical properties of Al20-xCr20 + 0.5xFe20Co20Ni20 + 0.5x high entropy alloys. J Alloys Compd. 2016;659:279–287. DOI:10.1016/j.jallcom.2015.10.258
7.
WaseemOA, LeeJ, LeeHM, . The effect of Ti on the sintering and mechanical properties of refractory-high entropy alloy TixWTaVCr fabricated via spark plasma sintering for fusion plasma-facing materials. Mater Chem Phys. 2018;210:87–94. DOI:10.1016/j.matchemphys.2017.06.054
8.
KimH, NamS, RohA, . Mechanical and electrical properties of NbMoTaW refractory high-entropy alloy thin films. Int J Refract Met Hard Mater. 2019;80:286–291. DOI:10.1016/j.ijrmhm.2019.02.005
9.
SenkovON, WilksGB, ScottJM, . Mechanical properties of Nb25Mo25Ta25W25 and V20Nb20Mo20Ta20W20 refractory high entropy alloys. Intermetallics. 2011;19:698–706. DOI:10.1016/j.intermet.2011.01.004
10.
GuoNN, WangL, LuoLS, . Microstructure and mechanical properties of refractory MoNbHfZrTi high-entropy alloy. Mater Des. 2015;81:87–94. DOI:10.1016/j.matdes.2015.05.019
11.
YehJW.Recent progress in high-entropy alloys. Annales de Chimie - Science des Matériaux. 2006;31:633–648. DOI:10.3166/acsm.31.633-648
12.
LiuY, ChengC, ShangJ, . Oxidation behavior of high-entropy alloys AlxCoCrFeNi (x = 0.15, 0.4) in supercritical water and comparison with HR3C steel. Trans Nonferr Metal Soc. 2015;25:1341–1351. DOI:10.1016/S1003-6326(15)63733-5
13.
ChenJ, NiuP, WeiT, . Fabrication and mechanical properties of AlCoNiCrFe high-entropy alloy particle reinforced Cu matrix composites. J Alloys Compd. 2015;649:630–634. DOI:10.1016/j.jallcom.2015.07.125
14.
WenLH, KouHC, LiJS, . Effect of aging temperature on microstructure and properties of AlCoCrCuFeNi high-entropy alloy. Intermetallics. 2009;17:266–269. DOI:10.1016/j.intermet.2008.08.012
15.
MaSG, QiaoJW, WangZH, . Microstructural features and tensile behaviors of the Al0.5CrCuFeNi2 high-entropy alloys by cold rolling and subsequent annealing. Mater Des. 2015;88:1057–1062. DOI:10.1016/j.matdes.2015.09.092
16.
SchuhB, Mendez-MartinF, VolkerB, . Mechanical properties, microstructure and thermal stability of a nanocrystalline CoCrFeMnNi high-entropy alloy after severe plastic deformation. Acta Mater. 2015;96:258–268. DOI:10.1016/j.actamat.2015.06.025
17.
WangXH, LiuSS, ZhaoGL, . Fabrication of in situ TiN ceramic particle reinforced high entropy alloy composite coatings by laser cladding processing. J Tribol. 2022;144:031402. DOI:10.1115/1.4051390
18.
JiangPF, ZhangCH, ZhangS, . Fabrication and wear behavior of TiC reinforced FeCoCrAlCu-based high entropy alloy coatings by laser surface alloying. Mater Chem Phys. 2020;255:123571. DOI:10.1016/j.matchemphys.2020.123571
19.
ZhouE, QiaoD, YangY, . A novel Cu-bearing high-entropy alloy with significant antibacterial behavior against corrosive marine biofilms. J Mater Sci Technol. 2020;46:201. DOI:10.1016/j.jmst.2020.01.039
20.
SanchezJM, VicarioI, AlbizuriJ, . Design, microstructure and mechanical properties of cast medium entropy aluminium alloys. Sci Rep. 2019;9:6792. DOI:10.1038/s41598-019-43329-w
21.
DasS, NishadSK, RobiPS.A new high-entropy alloy of Al-Fe-Co-Ni-Cu possessing single FCC crystal structure and excellent mechanical properties at room temperature. Phys Status Solidi A. 2021;218:2000825. DOI:10.1002/pssa.202000825
22.
CuiG, LiF, BianC, . High-temperature wear behavior of CoCr matrix coatings reinforced by niobium element from room temperature to 1000°C. J Tribol. 2022;144:101705. DOI:10.1115/1.4054591
23.
SimsekD.Effect on wear performance of ZrO2 amount of 316L stainless steel matrix composites produced by a mechanical alloying method. J Tribol. 2022;144:101708. DOI:10.1115/1.4054588
24.
AckerKV, VanhoyweghenD, PersoonsR, . Influence of tungsten carbide particle size and distribution on the wear resistance of laser clad WC/Ni coatings. WEAR. 2005;258:194–202. DOI:10.1016/j.wear.2004.09.041
25.
SunbulSE, IcinK, SerenFZ, . Determination of structural, tribological, isothermal oxidation and corrosion properties of Al–Co–Cr–Fe–Ni–Ti–Cu high-entropy alloy. Vacuum. 2021;187:110072. DOI:10.1016/j.vacuum.2021.110072
26.
DevarajuA.A Critical review on different types of wear of materials. Int J Mech Eng Engineering and Technology. 2015;6:77–83.
27.
NuruzzamanDM, ChowdhuryMA.Effect of normal load and sliding velocity on friction coefficient of aluminum sliding against different Pin materials. American Journal of Materials Science. 2012;2:26–31. DOI:10.5923/j.materials.20120201.05
28.
RabinowiczE.Friction and wear of materials. 2nd ed.New York: Wiley; 1995.
29.
Friction, Lubrication, and Wear Technology. ASM Handbook, Vol 18; 1992.
