The effects of cold work process between aging and solution heat treatment on the microstructure, hardness and the tribologic behaviour of a copper–beryllium (Cu–Be) alloy C17200 were investigated. The wear behaviour of the alloys was studied using ‘pin on disc’ method under dry conditions. The results show that the formation of fine grained structure and γ phase particles enhances the mechanical properties of the alloy; nonetheless, they do not reduce the wear rate. This is attributed to the capability of the softer specimens to maintain oxygen rich compounds during the dry sliding test.
‘ASM metals handbook, vol. 2: Properties and selection: nonferrous alloys and specific metal and alloys’, 1305–1312; 1993, Metals Park, OH, American Society for Metals.
‘ASM metals handbook, vol. 9: Metallography techniques and microstructures’, 810–817; 1993, Metals Park, OH, American Society for Metals.
4.
StobrawaJ., RdzawskZ., GłuchowskiW. and MalecW.: ‘Ultrafine grained strips of precipitation hardened copper alloys’, Arch. Metall. Mater., 2011, 56, 171–179.
5.
LiG. and ThomasB. G.: ‘Modeling creep and fatigue of copper alloys’, Metall. Mater. Trans., 2009, 13, 2491–2502.
6.
‘ASM metals handbook, vol. 4: Heat treatment: heat treatment of nonferrous alloy’, 1981–1994; 1993, Metals Park, OH, American Society for Metals.
7.
RyouM., LeeB. S. and KimM. H.: ‘Influence of aging treatment on the mechanical and electrical properties of Cu–0.5% Be alloy’, Mater. Sci. Eng., 2009, 24, 120–122.
KwokC. T. and WongP. K.: ‘Sliding wear and corrosion resistance of copper-based overhead catenary for traction systems’, Int. J. Railw., 2010, 3, 19–27.
10.
StraffeliniG., MainesL., PellizzariM. and ScardiP.: ‘Dry sliding wear of CuBe alloys’, Wear, 2005, 259, 506–511.
11.
ScardiP., LeoniM., StraffeliniG. and GiudiciG. D.: ‘Microstructure of Cu–Be alloy triboxidative wear debris’, Acta Mater., 2007, 55, 2531–2538.
12.
‘ASTM B 194. Standard specification for copper-beryllium alloy plate, sheet, strip, and rolled bar’, 2004, Philadelphia, ASTM Standards.
13.
KhachaturyanA. G. and LaughlinD. E.: ‘Structural transformations during decomposition in Cu–Be alloys’, Acta Metall. Mater., 1990, 38, 1823–1835.
14.
SakaiT., MiuraH. and MuramatsuN.: ‘Effect of small amount addition of Co on dynamic recrystallization of Cu–Be alloys’, Mater. Trans., 1995, 36, 1023–1030.
15.
CroneW. C.: ‘Compositional variation and precipitate structures of copper–beryllium single crystals grown by the bridgman technique’, J. Cryst. Growth, 2000, 218, 381–389.
16.
WilkesP.: ‘Formation of guinier-preston zones in Cu–Be alloys’, Acta. Metall., 1968, 16, 153–158.
17.
KooY. M. and CohenJ. B.: ‘The structure of GP zones in Cu–10.9 at% Be’, Acta Metall., 1989, 37, 1295–1306.
18.
MonzenR., SeoT., SakaiT. and WatanabeC.: ‘Precipitation processes in a Cu– 0.9%Be single crystal’, Mater. Trans., 2006, 47, 25–29.
19.
DjurićB., JovanovićM. and DrobnjakD. J.: ‘A study of precipitation in Cu–Be alloys’, Metallography, 1980, 13, 235–247.
20.
PriceR. J. and KellyA.: ‘Deformation of age hardened crystals of copper– 1.8wt% beryllium’, Acta Metall., 1963, 11, 915–922.
21.
PolataS., AtapekS¸. H., Eris¸irE., GümüşS. and Altug˘G. S.: ‘Microstructural characterization of aged copper alloy’. Proc. Int. Iron and Steel Symp., Karabük, Türkiye, 2012, Paper 214–218.
22.
YagmurL., DuyguluO. and AydemirB.: ‘Investigation of metastable γ′ precipitate using HRTEM in aged Cu–Be alloy’, Mater. Sci. Eng., 2011, 528, 4147–4151.
23.
ZhongY., SakaguchiT. and YinF.: ‘Effects of transformation twin on Hall–Petch relationship in MnCu alloy’, Mater. Sci. Eng., 2008, 492, 419–427.
24.
GuoliangX., QiangsongW., XujunM., BaiqingX. and LijunP.: ‘The precipitation behavior and strengthening of a Cu–2.0 wt% Be alloy’, Mater. Sci. Eng., 2012, 558, 326–330.
25.
AxenN. and JacobsonS.: ‘A model for the abrasive wear resistance of multiphase materials’, Wear, 1994, 174, 187–199.
26.
JiangJ., StottF. H. and StackM. M.: ‘A generic model for dry sliding wear of metals at elevated temperatures’, Wear, 2004, 256, 973–985.
SuhN. P.: ‘The delamination theory of wear’, Wear, 1973, 25, 111–124.
29.
JianJ., StottF. H. and StackM. M.: ‘The role of triboparticulates in dry sliding wear’, Tribol. Int., 1998, 31, 245–256.
30.
VenkataramanB. and SundararajanG.: ‘Correlation between the characteristics of the mechanically mixed layer and wear behavior of aluminum Al-7075 alloy and Al-MMCs’, Wear, 2000, 245, 22–38.
