SiC-reinforced SiC ceramic matrix composites (SiC/SiC CMCs) are considered promising candidates to replace their super alloy counterparts due to higher temperature capabilities and lower densities. However, high-temperature and high-pressure water vapour sourced from the hydrocarbons’ combustion reactions inhibit the potential of SiC/SiC CMCs by leading to rapid surface recession. In order to address this challenge, environmental barrier coatings (EBCs) have been developed. The emphasis of this review is on the materials and processing techniques for the development of EBC systems. In the first part of the review, the characteristics of the SiC/SiC CMCs and the most common EBC materials are summarised. Then, the interrelationship between processing methods, microstructures and the resulting properties is reviewed. Finally, an overview of the future directions is outlined to assist developments in advanced and novel EBCs for next generation gas turbines.
PadtureNP.Advanced structural ceramics in aerospace propulsion. Nat. Mater. 2016;15:804–809. doi:10.1038/nmat4687.
3.
LamonJ.Properties and characteristics of SiC and SiC/SiC composites. Amsterdam: Elsevier Inc.; 2012. p. 323–338. doi:10.1016/B978-0-08-056033-5.00022-7.
4.
LamourouxF, NaslainR, JouinJ-M.Kinetics and mechanisms of oxidation of 2D woven C/SiC composites: II, theoretical approach. J. Am. Ceram. Soc. 1994;77:2058–2068. doi:10.1111/j.1151-2916.1994.tb07097.x.
5.
HuC, TangS, PangS, Long-term oxidation behaviors of C/SiC composites with a SiC/UHTC/SiC three-layer coating in a wide temperature range. Corros. Sci. 2019;147:1–8. doi:10.1016/j.corsci.2018.10.017.
6.
LongbiaoL.Comparison of fatigue life between C/SiC and SiC/SiC ceramic-matrix composites at room and elevated temperatures. Appl Compos Mater. 2016;23:913–952. doi:10.1007/s10443-016-9492-5.
7.
Al NasiriN, PatraN, NiN, Oxidation behaviour of SiC/SiC ceramic matrix composites in air. J. Eur. Ceram. Soc. 2016;36:3293–3302. doi:10.1016/j.jeurceramsoc.2016.05.051.
8.
OpilaEJ.Oxidation and volatilization of silica formers in water vapor. J. Am. Ceram. Soc. 2003;86:1238–1248. doi:10.1111/j.1151-2916.2003.tb03459.x.
9.
NaslainR.Design, preparation and properties of non-oxide CMCs for application in engines and nuclear reactors: An overview. Compos. Sci. Technol. 2004;64:155–170. doi:10.1016/S0266-3538(03)00230-6.
10.
OpilaEJ.Variation of the oxidation rate of silicon carbide with water-vapor pressure. J. Am. Ceram. Soc. 1999;82:625–636. doi:10.1111/j.1151-2916.1999.tb01810.x.
11.
NaslainRR, PaillerRJF, LamonJL.Single- and multilayered interphases in SiC/SiC composites exposed to severe environmental conditions: An overview. Int. J. Appl. Ceram. Technol. 2010;7:263–275. doi:10.1111/j.1744-7402.2009.02424.x.
12.
KeransRJ, HayRS, ParthasarathyTA, Interface design for oxidation-resistant ceramic composites. J. Am. Ceram. Soc. 2002;85:2599–2632. doi:10.1111/j.1151-2916.2002.tb00505.x.
13.
NaslainR, DugneO, GuetteA, Boron nitride interphase in ceramic-matrix composites. J. Am. Ceram. Soc. 1991;74:2482–2488. doi:10.1111/j.1151-2916.1991.tb06789.x.
14.
ChristensenVL, ZokFW.Insights into internal oxidation of SiC/BN/SiC composites. J. Am. Ceram. Soc. 2023;106:1561–1575. doi:10.1111/jace.18834.
15.
MoreKL, TortorelliPF, WalkerLR, High-Temperature stability of SiC-based composites in high-water-vapor-pressure environments. J. Am. Ceram. Soc. 2003;86:1272–1281. doi:10.1111/j.1151-2916.2003.tb03463.x.
16.
Ruggles-WrennMB, JonesTP.Tension-compression fatigue of a SiC/SiC ceramic matrix composite at 1200 °c in air and in steam. Int J Fatigue. 2013;47:154–160. doi:10.1016/j.ijfatigue.2012.08.006.
17.
Ruggles-WrennMB, PopeMT, ZensTW.Creep behavior in interlaminar shear of a Hi-NicalonTM/SiC-B4C composite at 1200°C in air and in steam. Mater Sci Eng A. 2014;610:279–289. doi:10.1016/j.msea.2014.05.056.
18.
FaucettDC, ChoiSR. Strength Degradation of Oxide/Oxide and SiC/SiC Ceramic Matrix Composites in CMAS and CMAS/Salt Exposures, in: Vol. 1 Aircr. Engine; Ceram. Coal, Biomass Altern. Fuels; Wind Turbine Technol., ASMEDC, 2011: pp. 497–504. doi:10.1115/GT2011-46771.
19.
BasuSN, SarinVK.Thermal and environmental barrier coatings for Si-based ceramics. Amsterdam: Elsevier Ltd; 2014. p. 469–489. doi:10.1016/B978-0-08-096527-7.00036-2.
20.
LeeKN.Environmental barrier coatings for CMCs. CT: Wiley; 2015. pp. 430–451
21.
Tejero-MartinD, BennettC, HussainT.A review on environmental barrier coatings: history,: current state of the art and future developments. J. Eur. Ceram. Soc. 2021;41:1747–1768. doi:10.1016/j.jeurceramsoc.2020.10.057.
22.
ZhuD.Engineered Ceramics Advanced Ceramics and Ceramic Matrix CompositesJohn Wiley & Sons, Ltd; 2016. p. 187–202. doi10.1002/9781119100430.ch10.
23.
RobertsonAL, SoláF, ZhuD, Microscale fracture mechanisms of HfO 2 -Si environmental barrier coatings. J. Eur. Ceram. Soc. 2019;39:2409–2418. doi:10.1016/j.jeurceramsoc.2019.02.001.
24.
LeeKN, WatersDL, PuleoBJ, Development of oxide-based high temperature environmental barrier coatings for ceramic matrix composites via the slurry process. J. Eur. Ceram. Soc. 2021;41:1639–1653. doi:10.1016/J.JEURCERAMSOC.2020.10.012.
25.
LiG, LuX, HuangJ, Thermal cycling behavior and failure mechanism of the Si-HfO2 environmental barrier coating bond coats prepared by atmospheric plasma spraying. J. Alloys Compd. 2022;913(165319):1–13. doi:10.1016/j.jallcom.2022.165319.
26.
GuduruRK, DixitU, KumarA.A critical review on thermal spray based manufacturing technologies. Mater. Today Proc. 2022;62(Part 13):7265–7269. doi:10.1016/j.matpr.2022.04.107.
27.
LeeKN, MillerRA, JacobsonNS.New generation of plasma-sprayed mullite coatings on silicon carbide. J. Am. Ceram. Soc. 1995;78:705–710. doi:10.1111/j.1151-2916.1995.tb08236.x.
28.
LeeKN, FoxDS, EldridgeJI, Upper temperature limit of environmental barrier coatings based on mullite and BSAS. J. Am. Ceram. Soc. 2003;86:1299–1306. doi:10.1111/j.1151-2916.2003.tb03466.x.
29.
RichardsBT, WadleyHNG.Plasma spray deposition of tri-layer environmental barrier coatings. J. Eur. Ceram. Soc. 2014;34:3069–3083. doi:10.1016/j.jeurceramsoc.2014.04.027.
30.
RichardsBT, BegleyMR, WadleyHNG.Mechanisms of ytterbium monosilicate/mullite/silicon coating failure during thermal cycling in water vapor. J. Am. Ceram. Soc. 2015;98:4066–4075. doi:10.1111/jace.13792.
31.
RichardsBT, SehrS, De FranquevilleF, Fracture mechanisms of ytterbium monosilicate environmental barrier coatings during cyclic thermal exposure. Acta Mater. 2016;103:448–460. doi:10.1016/j.actamat.2015.10.019.
32.
RichardsBT, ZhaoH, WadleyHNG.Structure, composition, and defect control during plasma spray deposition of ytterbium silicate coatings. J. Mater. Sci. 2015;50:7939–7957. doi:10.1007/s10853-015-9358-5.
33.
RichardsBT, YoungKA, De FrancquevilleF, Response of ytterbium disilicate-silicon environmental barrier coatings to thermal cycling in water vapor. Acta Mater. 2016;106:1–14. doi:10.1016/j.actamat.2015.12.053.
34.
OlsonDH, DeijkersJA, Quiambao-TomkoK, Evolution of microstructure and thermal conductivity of multifunctional environmental barrier coating systems. Mater. Today Phys. 2021;17(100304):1–10. doi:10.1016/j.mtphys.2020.100304.
35.
CojocaruCV, LévesqueD, MoreauC, Performance of thermally sprayed Si/mullite/BSAS environmental barrier coatings exposed to thermal cycling in water vapor environment. Surf. Coatings Technol. 2013;216:215–223. doi:10.1016/j.surfcoat.2012.11.043.
36.
SuzukiM, SodeokaS, InoueT.Structure control of plasma sprayed zircon coating by substrate preheating and post heat treatment. Mater. Trans. 2005;46:669–674. doi:10.2320/matertrans.46.669.
37.
GarciaE, LeeH, SampathS.Phase and microstructure evolution in plasma sprayed Yb2Si2O7 coatings. J. Eur. Ceram. Soc. 2019;39:1477–1486. doi:10.1016/j.jeurceramsoc.2018.11.018.
38.
GarciaE, Sotelo-MazonO, Poblano-SalasCA, Characterization of Yb2Si2O7–Yb2SiO5 composite environmental barrier coatings resultant from in situ plasma spray processing. Ceram. Int. 2020;46:21328–21335. doi:10.1016/j.ceramint.2020.05.228.
39.
GarciaE, GarcesHF, TurcerLR, Crystallization behavior of air-plasma-sprayed ytterbium-silicate-based environmental barrier coatings. J. Eur. Ceram. Soc. 2021;41:3696–3705. doi:10.1016/j.jeurceramsoc.2020.12.051.
40.
ZhongX, NiuY, LiH, Thermal shock resistance of tri-layer Yb 2 SiO 5 /Yb 2 Si 2 O 7 /Si coating for SiC and SiC-matrix composites. J. Am. Ceram. Soc. 2018;101:4743–4752. doi:10.1111/jace.15713.
41.
YangH, YangY, CaoX, Thermal shock resistance and bonding strength of tri-layer Yb2SiO5/mullite/Si coating on SiCf/SiC composites. Ceram. Int. 2020;46:27292–27298. doi:10.1016/j.ceramint.2020.07.214.
42.
ZhongX, NiuY, LiH, Comparative study on high-temperature performance and thermal shock behavior of plasma-sprayed Yb2SiO5and Yb2Si2O7coatings. Surf. Coatings Technol. 2018;349:636–646. doi:10.1016/j.surfcoat.2018.06.056.
JordanEH, JiangC, GellM.The solution precursor plasma spray (SPPS) process: A review with energy considerations. J. Therm. Spray Technol. 2015;24:1153–1165. doi:10.1007/s11666-015-0272-9.
45.
RyuH, LeeSM, HanYS, Preparation of crystalline ytterbium disilicate environmental barrier coatings using suspension plasma spray. Ceram. Int. 2019;45:5801–5807. doi:10.1016/j.ceramint.2018.12.048.
46.
JiangC, CietekD, KumarR, Ytterbium silicate environmental barrier coatings deposited using the solution-based precursor plasma spray. J. Therm. Spray Technol. 2020;29:979–994. doi:10.1007/s11666-020-01046-1.
47.
BakanE, MauerG, SohnY, Application of high-velocity oxygen-fuel (HVOF) spraying to the fabrication of Yb-silicate environmental barrier coatings. Coatings. 2017;7(55):1–12. doi:10.3390/coatings7040055.
48.
Oberste BerghausJ, MarpleBR.High-velocity oxy-fuel (HVOF) suspension spraying of mullite coatings. J. Therm. Spray Technol. 2008;17:671–678. doi:10.1007/s11666-008-9219-8.
RamasamyS, TewariSN, LeeKN, Slurry based multilayer environmental barrier coatings for silicon carbide and silicon nitride ceramics - II. oxidation resistance. Surf. Coatings Technol. 2010;205:258–265. doi:10.1016/j.surfcoat.2010.07.048.
51.
RamasamyS, TewariSN, LeeKN, Slurry based multilayer environmental barrier coatings for silicon carbide and silicon nitride ceramics - II. oxidation resistance. Surf. Coatings Technol. 2010;205:266–270. doi:10.1016/j.surfcoat.2010.07.048.
52.
Al NasiriN, PatraN, PezoldtM, Investigation of a single-layer EBC deposited on SiC/SiC CMCs: processing and corrosion behaviour in high-temperature steam. J. Eur. Ceram. Soc. 2019;39:2703–2711. doi:10.1016/j.jeurceramsoc.2018.12.019.
53.
KimH, ChenM, YangQ, Sol-gel alumina environmental barrier coatings for SiC grit. Mater Sci Eng A. 2006;420:150–154. doi:10.1016/j.msea.2006.01.087.
54.
JayaseelanDD, UenoS, OhjiT, Sol-gel synthesis and coating of nanocrystalline Lu2Si 2O7 on Si3N4 substrate. Mater. Chem. Phys. 2004;84:192–195. doi:10.1016/j.matchemphys.2003.11.028.
55.
PriouxM, DuluardS, AnsartF, Advances in the control of electrophoretic process parameters to tune the ytterbium disilicate coatings microstructure. J. Am. Ceram. Soc. 2020;103. doi:10.1111/jace.17365.
56.
YilmazE, XiaoP.Effects of suspension properties on the fabrication of Yb2Si2O7 coatings using electrophoretic deposition. J. Eur. Ceram. Soc. 2021;42:638–648. doi:10.1016/j.jeurceramsoc.2021.10.038.
57.
BasuSN, KulkarniT, WangHZ, Functionally graded chemical vapor deposited mullite environmental barrier coatings for Si-based ceramics. J. Eur. Ceram. Soc. 2008;28:437–445. doi:10.1016/j.jeurceramsoc.2007.03.007.
58.
XuJ, SarinVK, DixitS, Stability of interfaces in hybrid EBC/TBC coatings for Si-based ceramics in corrosive environments. Int J Refract Met Hard Mater. 2015;49:339–349. doi:10.1016/j.ijrmhm.2014.08.013.
59.
YokoiT, YamaguchiN, TanakaM, Preparation of a dense ytterbium disilicate layer via dual electron beam physical vapor deposition at high temperature. Mater. Lett. 2017;193:176–178. doi:10.1016/j.matlet.2017.01.085.
60.
ZhangXF, ZhouKS, LiuM, Oxidation and thermal shock resistant properties of Al-modified environmental barrier coating on SiCf/SiC composites. Ceram. Int. 2017;43:13075–13082. doi:10.1016/j.ceramint.2017.06.167.
61.
HarderBJ.Oxidation performance of Si-HfO2 environmental barrier coating bond coats deposited via plasma spray-physical vapor deposition. Surf. Coatings Technol. 2020;384(125311):1–8. doi:10.1016/j.surfcoat.2019.125311.
62.
ZhangX, SongJ, DengZ, Interface evolution of Si/mullite/Yb2SiO5 PS-PVD environmental barrier coatings under high temperature. J. Eur. Ceram. Soc. 2020;40:1478–1487. doi:10.1016/j.jeurceramsoc.2019.10.062.
