Silicon carbide (SiC) monoliths were synthesised using nano-size SiC powder mixed with/without polysilazane by hot pressing at 1750°C for 1 h under an applied pressure of 20 MPa in N2 or Ar atmosphere. The effects of polysilazane and sintering atmosphere on the microstructure and hardness of SiC were examined. The grain sizes of the SiC ceramics sintered in N2 atmosphere with and without the polysilazane were 161 and 605 nm, while the density for those samples were 96.5 and 98.1%, respectively. It was shown that Si2N2O was formed for the SiC/polysilazane composite and sintered in N2. In addition, the sample mixed with polysilazane followed by sintering in N2 atmosphere revealed a quite high hardness in spite of its relatively low density. It was suggested that Si2N2O phase played an important role for the inhibition of grain and subsequent high hardness.
KimY. W. and MitomoM.: ‘Fine-grained silicon carbide ceramics with oxynitride glass’, J. Am. Ceram. Soc., 1999, 82, (10), 2731–2736. doi: 10.1111/j.1151-2916.1999.tb02149.x
4.
HottaM., KitaH. and HojoJ.: ‘Nanostructured silicon carbide ceramics fabricated through liquid-phase sintering by spark plasma sintering’, J. Ceram. Soc. Jpn., 2011, 119, (2), 129–132. doi: 10.2109/jcersj2.119.129
5.
LeeS. M., KimT. W., LimH. J., KimC., KimY. W. and LeeK. S.: ‘Mechanical properties and contact damages of nanostructured silicon carbide ceramics’, J. Ceram. Soc. Jpn., 2007, 115, (5), 304–309. doi: 10.2109/jcersj.115.304
6.
YamamotoT. A., KitauraH., KoderaY., IshiiT., OhyanagiM. and MunirZ. A.: ‘Mechanical properties of β-SiC fabricated by spark plasma sintering’, J. Mater. Eng. Perform., 2005, 14, 460–466. doi: 10.1361/105994905X56250
7.
LeeY. I., KimY. W., MitomoM. and KimD. Y.: ‘Fabrication of dense nanostructured silicon carbide ceramics through two-step sintering’, J. Am. Ceram. Soc., 2003, 86, (10), 1803–1805. doi: 10.1111/j.1151-2916.2003.tb03560.x
8.
XieM. L., LuoD. L., XianX. B., LengB. Y., ChenC. and LuW. Y.: ‘Densification of nano-SiC by ultra-high pressure effects of time, temperature and pressure’, Fusion Eng. Des., 2010, 85, 964–968. doi: 10.1016/j.fusengdes.2009.06.004
9.
YamamotoT. A., KitauraH., KoderaY., IshiiT., OhyanagiM. and MunirZ. A.: ‘Consolidation of nanostructured β-SiC by spark plasma sintering’, J. Am. Ceram. Soc., 2004, 87, (8), 1436–1441. doi: 10.1111/j.1551-2916.2004.01436.x
10.
HottaM. and HojoJ.: ‘Inhibition of grain growth in liquid-phase sintered SiC ceramics by AlN additive and spark plasma sintering’, J. Eur. Ceram. Soc., 2010, 30, 2117–2122. doi: 10.1016/j.jeurceramsoc.2010.04.006
11.
LorretteC., RéauA. and BriottetL.: ‘Mechanical properties of nanostructured silicon carbide consolidated by spark plasma sintering’, J. Eur. Ceram. Soc., 2013, 33, 147–156. doi: 10.1016/j.jeurceramsoc.2012.07.030
12.
LomelloF., BonnefontG., LeconteY., Herlin-BoimeN. and FantozziG.: ‘Processing of nano-SiC ceramics: densification by SPS and mechanical characterization’, J. Eur. Ceram. Soc., 2012, 32, 633–641. doi: 10.1016/j.jeurceramsoc.2011.10.006
13.
SuzukiT. S., UchikoshiT. and SakkaY.: ‘Densification of SiC by colloidal processing and SPS without sintering additives’, Adv. Appl. Ceram., 2014, 113, 85–88. doi: 10.1179/1743676113Y.0000000133
14.
NoviyantoA., HanY. H. and YoonD. H.: ‘Characteristic of SiCf/SiC hybrid composites fabricated by hot pressing and spark plasma sintering’, Adv. Appl. Ceram., 2011, 110, 375–381. doi: 10.1179/1743676111Y.0000000025
15.
CastellanE., ShahS. R. and RajR.: ‘Compression creep of alumina containing interfacial silicon, carbon, and nitrogen, derived from a polysilazane precursor’, J. Am. Ceram. Soc., 2010, 93, (4), 954–958. doi: 10.1111/j.1551-2916.2009.03515.x
16.
BrahmandamS. and RajR.: ‘Novel composites constituted from hafnia and a polymer-derived ceramic as an interface: phase for severe ultrahigh temperature applications’, J. Am. Ceram. Soc., 2007, 90, (10), 3171–3176. doi: 10.1111/j.1551-2916.2007.01879.x
17.
BarinI.: ‘Thermochemical data of pure substances’, 1334–1360; 1989, New York, VCH.
18.
NoviyantoA. and YoonD. H.: ‘Rare-earth oxide additives for the sintering of silicon carbide’, Diam. Relat. Mater., 2013, 38, 124–130. doi: 10.1016/j.diamond.2013.07.003
19.
HuangZ. K., GreilP. and PetzowG.: ‘Formation of silicon oxinitride from Si3N4 and SiO2 in the presence of Al2O3’, Ceram. Int., 1984, 10, 14–17. doi: 10.1016/0272-8842(84)90017-8
20.
HillertM., JonssonS. and SundmanB.: ‘Thermodynamic calculation of the Si – N – O system’, Z. Metallkd., 1992, 83, 648–654.
21.
GononM. F., FantozziG., MuratM. and DissonJ. P.: ‘Manufacture of monolithic ceramic bodies from polysilazane precursor’, J. Eur. Ceram. Soc., 1995, 15, 591–597. doi: 10.1016/0955-2219(95)00012-J
22.
XuH., BahtiaT., DeshpandeS. A., PadtureN. P., OrtizA. L. and CumbreraF. L.: ‘Microstructural evolution in liquid-phase-sintered SiC: part I, effect of starting powder’, J. Am. Ceram. Soc., 2001, 84, (7), 1578–1584. doi: 10.1111/j.1151-2916.2001.tb00880.x
23.
RagaruC., LancinM. and MarhicC.: ‘β⇒α phase transformation in SiC: link between polytypism, dihedral angle, and nucleation mechanism of α-twins’, J. Eur. Ceram. Soc., 1999, 19, 2701–2709. doi: 10.1016/S0955-2219(99)00051-5
24.
OrtizA. L., BhatiaT., PadtureN. P. and PezzottiG.: ‘Microstructural evolution in liquid-phase-sintered SiC: part III, effect of nitrogen-gas sintering atmosphere’, J. Am. Ceram. Soc., 2002, 85, (7), 1835–1840. doi: 10.1111/j.1151-2916.2002.tb00361.x
25.
KueckA. M. and De JongheL. C.: ‘Two-stage sintering inhibits abnormal grain growth during β to α transformation in SiC’, J. Eur. Ceram. Soc., 2008, 28, 2259–2264. doi: 10.1016/j.jeurceramsoc.2008.01.026
26.
Vargaz-GonzalesL., SpreyerR. F. and CampbellJ.: ‘Flexural strength, fracture toughness, and hardness of silicon carbide and boron carbide armor ceramics’, Int. J. Appl. Ceram. Tec., 2010, 7, 643–651. doi: 10.1111/j.1744-7402.2010.02501.x
27.
LoehmanR. E.: ‘Structure, formation and stability of oxynitride glasses’ in ‘Tailoring of mechanical properties of Si3N4 ceramics’, (ed. HoffmannM. J. and PetzowG.), 167–175; 1994, Dordrecht, Kluwer Academic Publisher.
28.
TongQ., ZhouY., ZhangJ., WangJ. and LiM.: ‘Preparation and properties of machinable Si2N2O/BN composites’, Int. J. Appl. Ceram. Tec., 2008, 5, 295–304. doi: 10.1111/j.1744-7402.2008.02197.x
29.
ScitiD. and BellosiA.: ‘Effect of additives on densification, microstructure and properties of liquid-phase sintered silicon carbide’, J. Mater. Sci., 2000, 35, 3849–3855. doi: 10.1023/A:1004881430804
30.
ZhouY., HiraoK., ToriyamaM., YamauchiY. and KanzakiS.: ‘Effects of intergranular phase chemistry on the microstructure and mechanical properties of silicon carbide ceramics densified with rare-earth oxide and alumina additions’, J. Am. Ceram. Soc., 2001, 84, (7), 1642–1644. doi: 10.1111/j.1151-2916.2001.tb00891.x
31.
BalogM., SajgalikP., HnatkoM., LencesZ., MonteverdeF., KeckesJ. and HuangJ.-L.: ‘Nano- versus macro-hardness of liquid phase sintered SiC’, J. Eur. Ceram. Soc., 2005, 25, 529–534. doi: 10.1016/j.jeurceramsoc.2004.01.026
