The deposition window of cold spray additive manufacturing (CSAM) a high-entropy alloy (HEA) was optimised by investigating processing parameters on deposition efficiency and porosity. The optimal parameters were obtained with helium as the driving gas, gas inlet temperature was at 700°C, and spray distance at 25 mm, at which the deposit was the thickest and of the lowest porosity. The type of driving gas is critical as it affects the porosity and deposition efficiency, and helium is required to obtain high-quality HEA deposits. With it, gas inlet temperature and spray distance have a minimal effect. Furthermore, higher gas temperature and moderate spraying distance were selected to increase particle deformation and reduce the effect of shock waves at the plate front.
YinS, LiWY, SongB, . Deposition of FeCoNiCrMn high entropy alloy (HEA) coating via cold spraying. J Mater Sci Technol. 2019;35(6):1003–1007.
6.
XuYX, LiWY, QuLZ, . Solid-state cold spraying of FeCoCrNiMn high-entropy alloy: an insight into microstructure evolution and oxidation behavior at 700-900°C. J Mater Sci Technol. 2021;68:172–183.
7.
LehtonenJ, KoivuluotoH, GeY, . Cold gas spraying of a high-entropy CrFeNiMn equiatomic alloy. Coatings. 2020;10(1):53.
8.
AhnJE, KimYK, YoonSH, . Tuning the Microstructure and Mechanical Properties of Cold Sprayed Equiatomic CoCrFeMnNi High-Entropy Alloy Coating Layer. Met Mater Int. 2020;27(7):2406–2415.
9.
AnupamA, KumarS, ChavanNM, . First report on cold-sprayed AlCoCrFeNi high-entropy alloy and its isothermal oxidation. J Mater Res. 2019;34(5):796–806.
10.
HuangRZ, SoneM, MaWH, . The effects of heat treatment on the mechanical properties of cold-sprayed coatings. Surf Coat Technol. 2015;261:278–288.
11.
ChenCY, XieYC, YinS, . Ductile and high strength Cu fabricated by solid-state cold spray additive manufacturing. J Mater Sci Technol. 2023;134:234–243.
12.
LiWY, CaoCC, YinS.Solid-state cold spraying of Ti and its alloys: a literature review. Prog Mater Sci. 2020;110:100633.
13.
LiWY, YangK, YinS, . Solid-state additive manufacturing and repairing by cold spraying: a review. J Mater Sci Technol. 2018;34(3):440–457.
14.
WanWP, LiWY, WuD, . New insights into the effects of powder injector inner diameter and overhang length on particle accelerating behavior in cold spray additive manufacturing by numerical simulation. Surf Coat Technol. 2022;444:128670.
15.
SchmidtT, GartnerF, AssadiH, . Development of a generalized parameter window for cold spray deposition. Acta Mater. 2006;54(3):729–742.
16.
YinS. A systematic investigation on the acceleration behavior and depostion mehcanism of cold sprayed particles [thesis]. Dalian University of Technology; 2012.
17.
JenTC, LiLJ, CuiWZ, . Numerical investigations on cold gas dynamic spray process with nano- and microsize particles. Int J Heat Mass Transfer. 2005;48(21):4384–4396.
18.
YinS, WangXF, LiWY, . Numerical study on the effect of substrate angle on particle impact velocity and normal velocity component in cold gas dynamic spraying based on CFD. J Therm Spray Techn. 2010;19(6):1155–1162.
19.
PattisonJ, CelottoS, KhanA, . Standoff distance and bow shock phenomena in the cold spray process. Surf Coat Technol. 2008;202(8):1443–1454.
20.
YinS, WangXF, LiWY.Computational analysis of the effect of nozzle cross-section shape on gas flow and particle acceleration in cold spraying. Surf Coat Technol. 2011;205(8):2970–2977.
21.
BagchiA.Probability theory an d mathematical statistics. Automatica (Oxf). 1985;21(4):504.
