Transformation-induced plasticity (TRIP) steel resistance spot welds are delicate to low-energy interfacial failure via crack propagation through martensitic fusion zone during cross-tension (CT) loading. This paper addresses the effect of three different types of in situ postweld heat treatment (PWHT) on the mechanical properties of TRIP steel resistance spot welds. Depending on the post weld second pulse current level, three different strengthening mechanisms were found including (i) martensite tempering with reduced hardness, (ii) refining of martensite packets with improved toughness and (iii) nugget re-melting/enlargement combined with possible reduction of grain boundary impurity segregation. All designed in situ PWHTs were enabled to promote pullout failure mode with improved load-bearing capacity and energy absorption capability during CT loading.
TasanCC, DiehlM, YanD, An overview of dual-phase steels: advances in microstructure-oriented processing and micromechanically guided design. Annu Rev Mater Res. 2015; 45:391–431. doi: 10.1146/annurev-matsci-070214-021103
PouranvariM, Alizadeh-ShM, MarashiSPH. Welding metallurgy of stainless steels during resistance spot welding part I: fusion zone. Sci Technol Weld Join. 2015; 20:502–511. doi: 10.1179/1362171815Y.0000000015
8.
ZhangH, SenkaraJ. Resistance welding: fundamentals and applications. London: Taylor & Francis CRC Press; 2005.
9.
LiY, CuiX, LuoZ, Microstructure and tensile-shear properties of resistance spot welded 22MnMoB hot-stamping annealed steel. J Mater Eng Perform. 2017; 26:424–430. doi: 10.1007/s11665-016-2448-y
10.
YangYP, GouldJ, PetersonW, Development of spot weld failure parameters for full vehicle crash modelling. Sci Technol Weld Join. 2013; 18:222–231. doi: 10.1179/1362171812Y.0000000082
11.
ZhangY, LiY, LuoZ, Effect of joint design on the failure behaviour of three-stack-up austenitic stainless steel resistance spot welds. Sci Technol Weld Join. 2016; 21:484–492. doi: 10.1080/13621718.2015.1135573
12.
ChaoYJ. Ultimate strength and failure mechanism of resistance spot weld subjected to tensile, shear, or combined tensile/shear loads. Trans Am Soc Mech Eng J Eng Mater Technol. 2003; 125:125–132. doi: 10.1115/1.1555648
13.
De CoomanBC. Structure-properties relationship in TRIP steels containing carbide-free bainite. Curr Opin Solid State Mater. 2004; 8:285–303. doi: 10.1016/j.cossms.2004.10.002
14.
BhadeshiaHKDH. Problems in the welding of automotive alloys. Sci Technol Weld Join. 2015; 20:451–453. doi: 10.1179/15Z.000000000379
15.
SunX, StephensEV, KhaleelMA. Effects of fusion zone size and failure mode on peak load and energy absorption of advanced high-strength steel spot welds. Weld J. 2007; 86:18s–25s.
16.
UijlNJD, SmithS. Resistance spot welding of advanced high strength steels for the automotive industry. In: Zhang W, Eder A, editors. Proceedings of the 4th International Seminar on Advances in Resistance Welding; 2006, pp. 30–60. Wels, Austria.
17.
NayakSS, Baltazar HernandezVH, OkitaY, Microstructure-hardness relationship in the fusion zone of TRIP steel welds. Mater Sci Eng A. 2012; 551:73–81. doi: 10.1016/j.msea.2012.04.096
18.
Baltazar HernandezVH, OkitaY, ZhouY. Second pulse current in resistance spot welded TRIP steel – effects on the microstructure and mechanical behavior. Weld J. 2012; 91:278–285.
19.
ChukoWL, GouldJE. Development of appropriate resistance spot welding practice for transformation-hardened steels. Weld J. 2002; 81:1s–7s.
20.
WeiST, LvD, LiuRD, Similar and dissimilar resistance spot welding of advanced high strength steels: welding and heat treatment procedures, structure and mechanical properties. Sci Technol Weld Join. 2014; 19:427–435. doi: 10.1179/1362171814Y.0000000211
21.
NikoosohbatF, KheirandishS, GoodarziM, Effect of tempering on the microstructure and mechanical properties of resistance spot welded DP980 dual phase steel. Mater Tehnol. 2015; 49:133–138.
22.
JahandidehAR, HamediM, MansourzadehSA, An experimental study on effects of postheating parameters on resistance spot welding of SAPH440 steel. Sci Technol Weld Join. 2011; 16:669–675. doi: 10.1179/1362171811Y.0000000053
23.
ShiG, WestgateSA. Techniques for improving the resistance spot weldability of 1.6–2.0 mm ultra-high strength steels for automotive applications. TWI report; 2005.
24.
ChukoW, GouldJE. Development of appropriate resistance spot welding practice for transformation-hardened steels. U.S. Department of Energy, Report to the American Iron and Steel Institute; 2002.
25.
UijlNJD, SmithS, GoosC, Failure modes of resistance spot welded advanced high strength steels. In: Zhang W, Scotchmer N, editors. Proceedings of the 5th International Seminar on Advances in Resistance Welding. Toronto, Canada; 2008. p. 78–104.
26.
SawanishiC, OguraT, TaniguchiK, Mechanical properties and microstructures of resistance spot welded DP980 steel joints using pulsed current pattern. Sci Technol Weld Join. 2014; 19:52–59. doi: 10.1179/1362171813Y.0000000165
PetersonW. Dilution of weld metal to eliminate interfacial fractures of spot welds in high and ultra-high strength steels. Paper presented at ICAWT 1997 International Conference, Advances in Welding Technology, Columbus; 1997 September 17–19; p. 331–346.
29.
PouranvariM. Susceptibility to interfacial failure mode in similar and dissimilar resistance spot welds of DP600 dual phase steel and low carbon steel during cross-tension and tensile-shear loading conditions. Mater Sci Eng A. 2012; 546:129–138. doi: 10.1016/j.msea.2012.03.040
30.
Recommended practices for test methods for evaluating the resistance spot welding behavior of automotive sheet steel materials. ANSI/AWS/SAE/D89-97. Miami, ML: AWS; 1997.
31.
GouldJE, KhuranaSP, LiT. Predictions of microstructures when welding automotive advanced high-strength steels. Weld J. 2006; 85:111s–116s.
32.
DancetteS, FabregueD, MassardierV, Experimental and modeling investigation of the failure resistance of advanced high strength steels spot welds. Eng Fail Anal. 2011; 78:2259–2272.
33.
PouranvariM. Fracture toughness of martensitic stainless steel resistance spot welds. Mater Sci Eng A. 2017; 680:97–107. doi: 10.1016/j.msea.2016.10.088
34.
OikawaH, MurayamaG, SakiyamaT, Resistance spot weldability of high strength steel (HSS) sheets for automobiles. Nippon Steel Techn Rep. 2007; 39:39–45.
35.
KraussG. Martensite in steel: strength and structure. Mater Sci Eng A. 1999; 273–275:40–57. doi: 10.1016/S0921-5093(99)00288-9
KimHJ, KimYH, MorrisJW. Thermal mechanisms of grain and packet refinement in a lath martensitic steel. ISIJ Int. 1998; 38:1277–1285. doi: 10.2355/isijinternational.38.1277
39.
HidalgoJ, SantofimiaMJ. Effect of prior austenite grain size refinement by thermal cycling on the microstructural features of as-quenched lath Martensite. Metall Mater Trans A. 2016; 47:5288–5301. doi: 10.1007/s11661-016-3525-4
