Friction stir processing (FSP) of high softening-temperature materials such as nickel-based superalloys is considered to be difficult. Laser heating of a localised area ahead of the FSP tool was used to provide sufficient plasticity during the FSP of IN738LC nickel-based superalloy. The stir zone (SZ) microstructure of the friction stir processed and laser-assisted friction stir processed were characterised. Laser-assisted friction stir processing (LAFSP) produced a defect-free pass, but FSP resulted in generation of a discontinuity in the SZ. Both lower volume fraction of partially dissolved γ′ precipitates and coarser grain structure of SZ in LAFSP led to more ductility of the SZ material and elimination of the defects.
PilchakA. L. and WilliamsJ. C.: ‘The effect of friction stir processing on the mechanical properties of investment cast and hot isostatically pressed Ti-6Al-4V’, Metal. Mater. Trans. A, 2011, 42, 773–794. doi:10.1007/s11661-010-0434-9.
2.
MishraR. S. and MaZ. Y.: ‘Friction stir welding and processing’, Mater. Sci. Eng. R, 2005, 50, 1–78. doi:10.1016/j.mser.2005.07.001.
3.
NandanR., DebRoyT. and BhadeshiaH.: ‘Recent advances in friction-stir welding–process, weldment structure and properties’, Prog. Mater. Sci., 2008, 53, 980–1023. doi:10.1016/j.pmatsci.2008.05.001.
4.
LiuZ., LiuD., XuJ., ZhengX., LiuQ. and XinR.: ‘Microstructural investigation and mechanical properties of dissimilar friction stir welded magnesium alloys’, Sci. Technol. Weld. Join., 2015, 20, 264–270. doi:10.1179/1362171815Y.0000000009.
5.
XuN., UejiR., and FujiiH.: ‘Enhanced mechanical properties of 70/30 brass joint by multi-pass friction stir welding with rapid cooling’, Sci. Technol. Weld. Join., 2015, 20, 91–99. doi:10.1179/1362171814Y.0000000261.
6.
MorisadaY., ImaizumiT., and FujiiH.: ‘Clarification of material flow and defect formation during friction stir welding’, Sci. Technol. Weld. Join., 2015, 20, 130–137. doi:10.1179/1362171814Y.0000000266.
7.
RaiR., DeA., BhadeshiaH. K. D. H. and DebRoyT.: ‘Review: friction stir welding tools’, Sci. Technol. Weld. Join., 2011, 16, 325–342. doi:10.1179/1362171811Y.0000000023.
8.
MaZ. Y.: ‘Friction stir processing technology: a review’, Metal. Mater. Trans. A, 2008, 39A, 642–658. doi: 10.1007/s11661-007-9459-0
9.
AhmadkhanihaD., SohiM. H., and Zarei-HanzakiA.: ‘Optimisation of friction stir processing parameters to produce sound and fine grain layers in pure magnesium’, Sci. Technol. Weld. Join., 2014, 19, 235–241. doi:10.1179/1362171813Y.0000000186.
10.
BorchersE., SiedA., BabuS. S., ShaferP. and ZhangW.: ‘Effect of filler metal and post-weld friction stir processing on stress corrosion cracking susceptibility of Al–Zn–Mg arc welds’, Sci. Technol. Weld. Join., 2015, 20, 460–467. doi:10.1179/1362171814Y.0000000273.
11.
MousavizadeS. M., Malek GhainiF., TorkamanyM. J., SabbaghzadehJ. and Abdollah-zadehA.: ‘Effect of severe plastic deformation on grain boundary liquation of a nickel–base superalloy’, Scripta. Mater., 2009, 60, 244–247. doi:10.1016/j.scriptamat.2008.10.021.
12.
ParkS. H. C., SatoY. S., KokawaH., OkamotoK., HiranoS. and InagakiM.: ‘Boride formation induced by pcBN tool wear in friction-stir-welded stainless steel’, Metal. Mater. Trans. A, 2009, 40A, 625–636. doi:10.1007/s11661-008-9709-9.
13.
RuleJ. R., RodelasJ. M. and LippoldJ. C.: ‘Application of friction stir processing as a pretreatment to fusion welding’, Weld. J., 2013, 92, 283–290.
14.
YeF., FujiiH., TsumuraT. and NakataK.: ‘Friction stir welding of Inconel alloy 600’, J. Mater. Sci., 2006, 41, 5376–5379. doi:10.1007/s10853-006-0169-6.
MandalS. and WilliamsonK.: ‘A thermomechanical hot channel approach for friction stir welding’, J. Mater. Process. Technol., 2006, 174, 190–194. doi:10.1016/j.jmatprotec.2005.12.012.
17.
FujiiH., TatsunoT., TsumuraT., TanakaM. and NakataK.: ‘Hybrid friction stir welding of carbon steel’, Mater. Sci. Forum., 2008, 580, 393–396. doi:10.4028/www.scientific.net/MSF.580-582.393.
18.
SunY. F., KonishiY., KamaiM. and FujiiH.: ‘Microstructure of S45C steel prepared by laser-assisted friction stir welding’, Mater. Des., 2013, 47, 842–849. doi:10.1016/j.matdes.2012.12.078
19.
ChangW. S., RajeshS. R., ChunC. K. and KimH. J.: ‘Microstructure and mechanical properties of hybrid laser-friction stir welding between AA6061-T6 Al Alloy and AZ31 Mg Alloy’, J. Mater. Sci. Technol., 2011, 27, 199–204. doi:10.1016/S1005-0302(11)60049-2.
20.
MironovS., SatoY. S. and KokawaH.: ‘Development of grain structure during friction stir welding of pure titanium’, Acta. Mater., 2009, 57, 4519–4528. doi:10.1016/j.actamat.2009.06.020.
21.
ElangovanK. and BalasubramanianV.: ‘Influences of pin profile and rotational speed of the tool on the formation of friction stir processing zone in AA2219 aluminium alloy’, Mater. Sci. Eng. A, 2007, 459, 7–18. doi:10.1016/j.msea.2006.12.124.
22.
BalasubramanianV.: ‘Relationship between base metal properties and friction stir welding process parameters’, Mater. Sci. Eng. A, 2008, 480, 397–403. doi:10.1016/j.msea.2007.07.048
23.
OjoO. A., RichardsN. L. and ChaturvediM. C.: ‘Contribution of constitutional liquation of gamma prime precipitate to weld HAZ cracking of cast Inconel 738 superalloy’, Scripta. Mater., 2004, 50, 641–646. doi:10.1016/j.scriptamat.2003.11.025.
24.
LiY., MurrL. E. and McClureJ. C.: ‘Flow visualization and residual microstructures associated with the friction-stir welding of 2024 aluminum to 6061 aluminum’, Mater. Sci. Eng. A, 1999, 271, 213–223. doi:10.1016/S0921-5093(99)00204-X.
25.
JataK. V. and SemiatinS. L.: ‘Continuous dynamic recrystallization during friction stir welding of high strength aluminum alloys
’, Scripta. Mater., 2000, 43, 743–749. doi:10.1016/S1359-6462(00)00480-2.
26.
ChamafarA., JahaziM., GholipourJ., WanjaraP., and YueS.: ‘Mechanical property and microstructure of linear friction welded waspaloy’, Metal. Mater. Trans. A, 2011, 42, 729–744. doi:10.1007/s11661-010-0457-2.
