In this study, a pretreatment of sand blasting (SB) was carried out prior to plasma nitriding to enhance the nitriding efficiency and improve the wear resistance for 304 austenitic stainless steel. The surface morphology, microstructure, phase constituents and wear resistance were systematically investigated by means of scanning electron microscopy, optical microscopy, Vickers hardness tester, X-ray diffraction and pin-on-disk tribotester, etc. The results showed that SB had significant enhancement effect on nitriding efficiency and wear resistance. Meanwhile, the enhancement effect is duration dependent; the optimal wear resistance is obtained at SB duration of 15 min, which is mainly ascribed to the excellent protection from the thicker and denser compound layer.
El-HossaryFM, NegmNZ, Abd El-RahmanAM, Duplex treatment of 304 AISI stainless steel using rf plasma nitriding and carbonitriding. Mater Sci Eng C. 2009;29:1167–1173. doi: 10.1016/j.msec.2008.09.049
2.
WangSK, CaiW, LiJC, A novel rapid D.C. plasma nitriding at low gas pressure for 304 austenitic stainless steel. Mater Lett. 2013;105:47–49. doi: 10.1016/j.matlet.2013.04.031
3.
NakajimaM, NakamuraY, SuzukiK, Effect of solution treatment after nitriding on fatigue properties in type 304 stainless steel. Int J Fatigue. 2014;68:103–110. doi: 10.1016/j.ijfatigue.2014.05.013
4.
LinYM, LuJ, WangLP, Surface nanocrystallization by surface mechanical attrition treatment and its effect on structure and properties of plasma nitrided AISI 321 stainless steel. Acta Mater. 2006;54:5599–5605. doi: 10.1016/j.actamat.2006.08.014
5.
LiuH, LiJC, ChaiYT, A novel plasma oxynitriding by using plain air for AISI 1045 steel. Vacuum. 2015;121:18–21. doi: 10.1016/j.vacuum.2015.07.012
6.
TangL, SunF, MiaoXJ, Evolution of pre-oxide layer during subsequent plasma nitriding. Vacuum. 2018;152:337–339. doi: 10.1016/j.vacuum.2018.03.057
7.
MiaoB, SongL, ChaiYT, The effect of sand blasting pretreatment on plasma nitriding. Vacuum. 2017;136:46–50. doi: 10.1016/j.vacuum.2016.11.019
8.
LuSJ, MiaoB, SongL, Enhancement of wear resistance of AISI 1045 steel by a two-step plasma treatment. Vacuum. 2017;145:153–157. doi: 10.1016/j.vacuum.2017.08.026
9.
TaherkhaniK, SoltaniehM.Composite coatings created by new method of active screen plasma nitriding on aluminium alloy 6061. J Alloy Compd. 2018;741:1247–1257. doi: 10.1016/j.jallcom.2017.12.360
10.
ChenY, SongL, ZhangCK, Plasma nitriding without formation of compound layer for 38CrMoAl hydraulic plunger. Vacuum. 2017;143:98–101. doi: 10.1016/j.vacuum.2017.05.036
11.
WuJQ, LiuH, LiJC, Comparative study of plasma oxynitriding and plasma nitriding for AISI 4140 steel. J Alloy Compd. 2016;680:642–645. doi: 10.1016/j.jallcom.2016.04.172
12.
LiuH, LiJC, SunF, Characterization and effect of pre-oxidation on D.C. plasma nitriding for AISI4140 steel. Vacuum. 2014;109:170–174. doi: 10.1016/j.vacuum.2014.07.017
13.
MiaoB, LiuH, LiJC, Kinetics comparison between plasma oxynitriding and plasma nitriding and the application for AISI 1045 steel. Surf Eng. 2018;34:146–150. doi: 10.1080/02670844.2016.1237080
14.
MiaoB, ChaiYT, WeiKX, A novel duplex plasma treatment combining plasma nitrocarburizing and plasma nitriding. Vacuum. 2016;133:54–57. doi: 10.1016/j.vacuum.2016.07.007
15.
BalusamyT, NarayananTSNS, RavichandranK, Plasma nitriding of AISI 304 stainless steel: Role of surface mechanical attrition treatment. Mater Charact. 2013;85:38–47. doi: 10.1016/j.matchar.2013.08.009
16.
YaoQT, SunJ, ZhangGL, Enhanced toughness of nitrided layers formed on Ti-6Al-4V alloy via surface mechanical attrition pre-treatment. Vacuum. 2017;142:45–51. doi: 10.1016/j.vacuum.2017.05.004
17.
BalusamyT, NarayananTSNS, RavichandranK, Pack boronizing of AISI H11 tool steel: Role of surface mechanical attrition treatment. Vacuum. 2013;97:36–43. doi: 10.1016/j.vacuum.2013.04.006
18.
GateyAM, HosmaniSS, FigueroaCA, Role of surface mechanical attrition treatment and chemical etching on plasma nitriding behavior of AISI 304L steel. Surf Coat Tech. 2016;304:413–424. doi: 10.1016/j.surfcoat.2016.07.020
19.
TangL, JiaW, HuJ.An enhanced rapid plasma nitriding by laser shock peening. Mater Lett. 2018;231:91–93. doi: 10.1016/j.matlet.2018.08.010
20.
SongL, GuXM, SunF, Reduced internal oxidation by a rapid carburizing technology enhanced by pre-oxidation for 18CrNiMo7-6 gear steel. Vacuum. 2019;160:210–212. doi: 10.1016/j.vacuum.2018.11.006
21.
LuSJ, ZhaoXB, WangSK, Performance enhancement by plasma nitriding at low gas pressure for 304 austenitic stainless steel. Vacuum. 2017;145:334–339. doi: 10.1016/j.vacuum.2017.09.020
22.
LiJC, YangXM, WangSK, A rapid D.C. plasma nitriding technology catalyzed by pre-oxidation for AISI4140 steel. Mater Lett. 2014;116:199–202. doi: 10.1016/j.matlet.2013.11.033
23.
El-HossaryFM.Effect of rf plasma nitriding power density on microhardness, structure, and magnetic properties of 304 austenite stainless steel. Surf Eng. 2000;16:491–494. doi: 10.1179/026708400101517495
