The Ni60A-Cr3C2 coatings with different Nb addition were prepared by laser cladding. The microstructure was observed by SEM and TEM. The chemical composition of phases was studied by X-ray diffractometer and Electron Probe Micro-analyzer (EPMA). Microhardness and wear behaviour were measured by microhardness tester and wear tester, respectively. The results show that the main phases in Ni60A-Cr3C2 coating are γ-Ni, Cr7C3, Cr23C6, Ni3Si2, Ni3B and CrB. With Nb addition, the NbC phase appears in the coatings. The size and volume fraction of NbC increase with the increase of Nb addition. The hardness and wear resistance increase first and then decrease with the increase of Nb addition. The micro-hardness of coatings with 2 wt-% Nb addition is the highest, reaching 1046.6 Hv0.2. The relative abrasive resistance of coatings with 3 wt-% Nb addition is the best, and is 2.33 times that of Nb-free coatings.
KaimingW, YulongL, HanguangF, A study of laser cladding NiCrBSi/Mo composite coatings. Surf Eng. 2018;34:267–275. doi: 10.1080/02670844.2016.1259096
2.
RenJ, LiuX-B, LuX-L, Microstructure and tribological properties of self-lubricating antiwear composite coating on Ti6Al4V alloy. Surf Eng. 2017;33:20–26. doi: 10.1179/1743294415Y.0000000054
3.
WengF, YuH, ChenC, Effect of process parameters on the microstructure evolution and wear property of the laser cladding coatings on Ti-6Al-4V alloy. J Alloys Compd. 2017;692:989–996. doi: 10.1016/j.jallcom.2016.09.071
4.
TanCL, ZhuHM, KuangTC, Laser cladding Al-based amorphous-nanocrystalline composite coatings on AZ80 magnesium alloy under water cooling condition. J Alloys Compd. 2017;690:108–115. doi: 10.1016/j.jallcom.2016.08.082
5.
FarahmandP, LiuS, ZhangZ, Laser cladding assisted by induction heating of NieWC composite enhanced by nano-WC and La2O3. Ceram Int. 2014;40:15421–15438. doi: 10.1016/j.ceramint.2014.06.097
6.
HuangC, ZhangYZ, VilarR, Dry sliding wear behavior of laser clad TiVCrAlSi high entropy alloy coatings on Ti-6Al-4V substrate. Mater Des. 2012;41:338–343. doi: 10.1016/j.matdes.2012.04.049
7.
MaQS, LiYJ, WangJ, Investigation on cored-eutectic structure in Ni60/WC composite coatings fabricated by wide-band laser cladding. J Alloys Compd. 2015;645:151–157. doi: 10.1016/j.jallcom.2015.04.136
8.
SharmaSP, DwivediDK, JainPK.Effect of La2O3 addition on the microstructure, hardness and abrasive wear behavior of flame sprayed Ni based coatings. Wear. 2009;267(5-8):853–859. doi: 10.1016/j.wear.2008.12.029
9.
ChaliampaliasD, VourliasG, PavlidouE, Comparative examination of the microstructure and high temperature oxidation performance of NiCrBSi flame sprayed and pack cementation coatings. Appl Surf Sci. 2009;255(6):3605–3612. doi: 10.1016/j.apsusc.2008.10.006
10.
WangPZ, QuJX, ShaoHS.Cemented carbide reinforced nickel-based alloy coating by laser cladding and the wear characteristics. Mater Des. 1996;17(5-6):289–296. doi: 10.1016/S0261-3069(97)00025-3
11.
ZhangJ, HuY, TanXJ, Microstructure and high temperature tribological behavior of laser cladding Ni60A alloys coatings on 45 steel substrate. Trans Nonferrous Met Soc China. 2015;25(5):1525–1532. doi: 10.1016/S1003-6326(15)63754-2
12.
MatthewsS, JamesB, HylandM.High temperature erosion-oxidation of Cr3C2-NiCr thermal spray coatings under simulated turbine conditions. Corros Sci. 2013;70:203–211. doi: 10.1016/j.corsci.2013.01.030
13.
ChenY, ChaoYJ, LuoZ, Microstructure and wear resistance of Co-based/Cr3C2 coatings with CeO2. Surf Eng. 2018;34(8):588–595. doi: 10.1080/02670844.2017.1363484
14.
ZhangDW, LeiTC.The microstructure and erosive-corrosive wear performance of laser-clad Ni-Cr3C2 composite coating. Wear. 2003;255:129–133. doi: 10.1016/S0043-1648(03)00283-7
15.
WangD, WangWQ, ChenXG, Influence of Cr addition on the interface purification of vacuum brazed NiCr-Cr3C2 coatings on single crystal superalloy. Surf Coat Technol. 2017;325:200–209. doi: 10.1016/j.surfcoat.2017.06.054
16.
PingXL, SunST, WangF, Effect of Cr3C2 addition on the microstructure and properties of laser cladding NiCrBSi coatings. Surf Rev Lett. 2018: 1850207. 10 pages. doi:10.1142/S0218625X18502074.
17.
YangLQ, LiZY, ZhangYQ, Al-TiC in situ composite coating fabricated by low power pulsed laser cladding on AZ91D magnesium alloy. Appl Surf Sci. 2018;435:1187–1198. doi: 10.1016/j.apsusc.2017.11.240
18.
XiangH, XuY, ZhangL, Synthesis and microstructure of Tantalum carbide and carbon composite by liquid precursor route. Scr Mater. 2006;55(4):339–342. doi: 10.1016/j.scriptamat.2006.04.036
19.
RaminA, MahmoodS, GhodratollahR, Effects of Ti addition on the microstructure and mechanical properties of multi-pass E6010 high-cellulosic electrode weld metal. Appl Phys A. 2018;124(11):772-1–772-12.
20.
YanY, CunliangP, RuihuaZ. The effect of Ti addition on the microstructure and properties of high chromium iron-based coatings. J Alloys Compd. 2018;765:782–790.
21.
Hu YL, LinX, Yu XB, Effect of Ti addition on cracking and microhardness of Inconel 625 during the laser solid forming processing. J Alloys Compd. 2017;711:267–277. doi: 10.1016/j.jallcom.2017.03.355
22.
YuT, Deng QL, DongG, Effects of Ta on microstructure and microhardness of Ni based laser clad coating. Appl Surf Sci. 2011;257:5098–5103. doi: 10.1016/j.apsusc.2011.01.027
23.
LiuK, LiYJ, WangJ, Effect of high dilution on the in situ synthesis of Ni-Zr/Zr-Si(B, C) reinforced composite coating on zirconium alloy substrate by laser cladding. Mater Des. 2015;87:66–74. doi: 10.1016/j.matdes.2015.07.158
24.
HuangSG, LiuRL, LiL, NbC as grain growth inhibitor and carbide in WC-Co hard metals. Int J Refract Met Hard Mater. 2008;26(5):389–395. doi: 10.1016/j.ijrmhm.2007.09.003
GilliardMB, PieriniBT, AlconchelSA.In situ formation of Fe-NbC/C composite powders from solution-derived precursors by a gas reduction-carburization process. Ceram Int. 2014;40:14881–14889. doi: 10.1016/j.ceramint.2014.06.083
27.
NiuX, ChaoMJ, WangWL, In situ Synthesized NbC Particulate Reinforced Ni-based composite coatings by laser cladding. Chinese J Lasers. 2006;33(7):987–992.
28.
LiQT, LeiYP, FuHG, Growth characteristics and Reinforcing Behavior of In-situ NbCp in laser Cladded Fe-based composite coating. J Mater Sci Technol. 2015;31(7):766–772. doi: 10.1016/j.jmst.2014.06.012
29.
ChengY, DongG, Chen GX, Effect of niobium on microstructure and microhardness of laser clad nickel based alloy. Mater Mech Eng. 2014;38(9):24–30. doi: 10.1016/j.msea.2014.03.075
30.
CaoYB, ZhiSX, GaoQ, Formation behavior of in-situ NbC in Fe-based laser cladding coatings. Mater Charact. 2016;119:159–165. doi: 10.1016/j.matchar.2016.08.005
31.
ZhangPL, LuYL, YanH, Effect of a small addition of Ti on the Fe-based coating by laser cladding. Surf Coat Technol. 2013;236:84–90. doi: 10.1016/j.surfcoat.2013.09.032
32.
PingXL, FuHG, SunST, Effect of Nb addition on microstructure and properties of laser cladding NiCrBSi coatings. Trans IMF. 2018;96(6):304–312. doi: 10.1080/00202967.2018.1502934
33.
Instructions for IPG Lasers. Beijing; 2016.
34.
DongG, YanB, DengQL, Effect of niobium on the microstructure and wear resistance of nickel-based alloy coating by laser cladding. Rare Met Mater Eng. 2011;40(6):973–977.
35.
WangDZ, HuQW, ZengXY.Microstructures and performances of Cr13Ni5Si2 based composite coatings deposited by laser cladding and laser - induction hybrid cladding. J Alloys Compd. 2014;588(5):502–508. doi: 10.1016/j.jallcom.2013.11.069
36.
ZhouSF, LeiJB, DaiXQ, A comparative study of the structure and wear resistance of NiCrBSi/50 wt.% WC composite coatings by laser cladding and laser induction hybrid cladding. Int J Refract Met Hard Mater. 2016;60:17–27. doi: 10.1016/j.ijrmhm.2016.06.019
37.
LuXL, LiuXB, YuPC.Effects of annealing on laser clad Ti2SC/CrS self-lubricating anti-wear composite coatings on Ti6Al4V alloy: microstructure and tribology. Tribol Int. 2016;101:356–363. doi: 10.1016/j.triboint.2016.05.004
