Cyclic nanoimpact tests were carried on nc-TiAlN/a-Si3N4 nanocomposite, TiN and multilayered TiN/nanocomposite (NC) coatings to evaluate their resistance to fracture under cyclic impact loads. Fracture behaviour of the coatings was ascertained from fracture probability obtained from time-depth curves and focus ion beam milling images of resulting indentation impressions. TiN coating mainly showed intercolumnar cracks while the other coatings showed other modes of cracking, that is, lateral, inclined, bending, edge cracks, during testing. The performance ranking of the coatings, TiN > TiN/NC > nc-TiAlN/a-Si3N4, is linked to their β0 value, representing relative indentation depth of the coating-substrate composite hardness system at which the fractional hardness improvement equal to 50% of the maximum is retained and also their corresponding microstructure. Apart from enabling prediction of fracture resistance of the coatings, these studies provide useful insights into design and selection of coating materials for targeted machining applications.
SureshaS. J., MathS., JayaramV. and BiswasS. K.: ‘Toughening through multilayering in TiN–AlTiN films’, Philos. Mag., 2007,
87, (17), 2521–2539. doi: 10.1080/14786430701230245
2.
BhowmickS., BhideR., HoffmanM., JayaramV. and BiswasS. K.: ‘Fracture mode transitions during indentation of columnar TiN coatings on metal’, Philos. Mag., 2005,
85, (25) (1), 2927–2945. doi: 10.1080/14786430500155213
3.
BeakeB. D., GoodesS. R. and SmithJ. F.: ‘Micro-impact testing: a new technique for investigating thin film toughness, adhesion, erosive wear resistance and dynamic hardness’, Surf. Eng., 2001,
17, (3), 187–192. doi: 10.1179/026708401101517755
4.
BeakeB. D. and SmithJ. F.: ‘Nano-impact testing – an effective tool for assessing the resistance of advanced wear-resistant coatings to fatigue failure and delamination’, Surf. Coat. Technol., 2004,
188–189, 594–598. doi: 10.1016/j.surfcoat.2004.07.016
5.
ConstantinidesG., TweedieC. A., SavvaN., SmithJ. F. and Van VlietK. J.: ‘Quantitative impact testing of energy dissipation at surfaces’, Exp. Mech., 2009,
49, 511–522. doi: 10.1007/s11340-008-9198-1
6.
ChenJ., ShiX., BeakeB. D., GuoX., WangZ., ZhangY. and GoodesS. R.: ‘An investigation into the dynamic indentation response of metallic materials’, J. Mater. Sci., 2016,
51, (18), 8310–8322. doi: 10.1007/s10853-016-0031-4
7.
WheelerJ. M. and GunnerA. G.: ‘Analysis of failure modes under nano-impact fatigue of coatings via high-speed sampling’, Surf. Coat. Technol., 2013,
232, 264–268. doi: 10.1016/j.surfcoat.2013.05.028
8.
BeakeB. D., Fox-RabinovichG. S., VeldhuisS. C. and GoodesS. R.: ‘Coating optimisation for high speed machining with advanced nanomechanical test methods’, Surf. Coat. Technol., 2009,
203, 1919–1925. doi: 10.1016/j.surfcoat.2009.01.025
9.
IkedaS., GillesS. and ChenevierB.: ‘Electron microscopy analysis of the microstructure of Ti1−xAlxN alloy thin films prepared using a chemical vapour deposition method’, Thin Solid Films, 1998,
315, 257–262. doi: 10.1016/S0040-6090(97)00706-2
10.
PaldeyS. and DeeviS. C.: ‘Single layer and multilayer wear resistant coatings of (TiAl)N: a review’, Mater. Sci. Eng., 2003,
342, 58–79. doi: 10.1016/S0921-5093(02)00259-9
11.
LiuZ., AnQ., XuJ., ChenM. and HanS.: ‘Wear performance of (nc-AlTiN)/(a-Si3N4) coating and (nc-AlCrN)/(a-Si3N4) coating in high-speed machining of titanium alloys under dry and minimum quantity lubrication (MQL) conditions’, Wear, 2013,
305, 249–259. doi: 10.1016/j.wear.2013.02.001
12.
VeprekS. and JilekM.: ‘Super- and ultrahard nanocomposite coatings: generic concept for their preparation, properties and industrial applications’, Vacuum, 2002,
67, 443–449. doi: 10.1016/S0042-207X(02)00229-4
13.
VeprekS. and Veprek-HeijmanM. J. G.: ‘Industrial applications of superhard nanocomposite coatings’, Surf. Coat. Technol., 2008,
202, 5063–5073. doi: 10.1016/j.surfcoat.2008.05.038
14.
YaoY., LiJ., WangY., YeY. and ZhuL.: ‘Influence of the negative bias in ion plating on the microstructural and tribological performances of Ti–Si–N coatings in seawater’, Surf. Coat. Technol., 2015,
280, 154–162. doi: 10.1016/j.surfcoat.2015.09.005
15.
RicoA., MúnezC. J. and RodríguezJ.: ‘On the relevance of microstructure in the fracture toughness of nanostructured alumina–13% titania coatings’, Surf. Coat. Technol., 2014,
243, 46–50. doi: 10.1016/j.surfcoat.2012.03.021
16.
ZhangS., WangH. L., OngS. E., SunD. and BuiX. L.: ‘Hard yet tough nanocomposite coatings – present status and future trends’, Plasma Process. Polym., 2007,
4, 219–228. doi: 10.1002/ppap.200600179
17.
LeylandA. and MatthewsA.: ‘On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behaviour’, Wear, 2000,
246, 1–11. doi: 10.1016/S0043-1648(00)00488-9
18.
MusilJ. and JiroutM.: ‘Toughness of hard nanostructured ceramic thin films’, Surf. Coat. Technol., 2007,
201, 5148–5152. doi: 10.1016/j.surfcoat.2006.07.020
19.
ZhangS., SunD., FuY. and DuH.: ‘Toughening of hard nanostructural thin films: a critical review’, Surf. Coat. Technol., 2005,
198, 2–8. doi: 10.1016/j.surfcoat.2004.10.020
20.
SivitskiA., GregorA., SaarnaM., KuluP. and SergejevF.: ‘Properties and performance of hard coatings on tool steels under cyclic indentation’, Acta Mech. Slovaka, 2009,
13, (3), 84–95.
21.
ChenJ., JiR., KhanR. H. U., LiX., BeakeB. D. and DongH.: ‘Effects of mechanical properties and layer structure on the cyclic dynamic loading of TiN-based coatings’, Surf. Coat. Technol., 2011,
206, 522–529. doi: 10.1016/j.surfcoat.2011.07.079
22.
RaviN., MarkandeyaR. and JoshiS. V.: ‘Effect of substrate roughness on adhesion and tribological properties of nc-TiAlN/a-Si3N4 nanocomposite coatings deposited by cathodic arc PVD process’, Surf. Eng., 2016. doi:10.1179/1743294415Y.0000000005.
23.
BeakeB. D., VishnyakovV. M. and ColligonJ. S.: ‘Nano-impact testing of TiFeN and TiFeMoN films for dynamic toughness evaluation’, J. Phys. D Appl. Phys., 2011,
44, 085301–85308. doi: 10.1088/0022-3727/44/8/085301
24.
SkordarisG., BouzakisK.-D., CharalampousP., BouzakisE., ParaskevopoulouR., LemmerO. and BolzS.: ‘Brittleness and fatigue effect of mono- and multi-layer PVD films on the cutting performance of coated cemented carbide inserts’, CIRP Ann. Manuf. Technol., 2014,
63, 93–96. doi: 10.1016/j.cirp.2014.03.081
25.
OliverW. C. and PharrG. M.: ‘An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments’, J. Mater. Res., 1992,
7, (6), 1564–1583. doi: 10.1557/JMR.1992.1564
26.
FaisalN. H., AhmedR., GoelS. and FudY. Q.: ‘Influence of test methodology and probe geometry on nanoscale fatigue failure of diamond-like carbon film’, Surf. Coat. Technol., 2014,
242, 42–53. doi: 10.1016/j.surfcoat.2014.01.015
27.
BeakeB. D., LauS. P. and SmithJ. F.: ‘Evaluating the fracture properties and fatigue wear of tetrahedral amorphous carbon films on silicon by nano-impact testing’, Surf. Coat. Technol., 2004,
177–178, 611–615. doi: 10.1016/S0257-8972(03)00934-4
28.
TuckJ. R., KorsunskyA. M., BhatD. G. and BullS. J.: ‘Indentation hardness evaluation of cathodic arc deposited thin hard coatings’, Surf. Coat. Technol., 2001,
139, 63–74. doi: 10.1016/S0257-8972(00)01116-6
29.
ChenJ., LiH. and BeakeB. D.: ‘Load sensitivity in repetitive nano-impact testing of TiN and AlTiN coatings’, Surf. Coat. Technol., 2016. doi:10.1016/j.Surfcoat.2016.05.094.
30.
BeakeB. D. and Fox-RabinovichG. S.: ‘Advanced nanomechanical testing for high speed machining of hard-to-cut aerospace alloys’, Int. Heat Treat. Surf. Eng., 2011,
5, (1), 17–20. doi: 10.1179/174951411X12956208225302
31.
SubramanianC., StraffordK. N., WilksT. P., WardL. P. and McMillanW.: ‘Influence of substrate roughness on the scratch adhesion of titanium nitride coatings’, Surf. Coat. Technol., 1993,
62, 529–535. doi: 10.1016/0257-8972(93)90295-Y
32.
ShiK., WangC., GrossC. and ChungY-W: ‘Reversing the inverse hardness–toughness trend using W/VC multilayer coatings’, Surf. Coat. Technol., 2015,
284, 80–84. doi: 10.1016/j.surfcoat.2015.06.086
33.
MaL. W., CairneyJ. M., HoffmanM. and MunroeP. R.: ‘Deformation and fracture of TiN and TiAlN coatings on a steel substrate during nanoindentation’, Surf. Coat. Technol., 2006,
200, 3518–3526. doi: 10.1016/j.surfcoat.2004.09.034
34.
YalamanchiliK., ForsénR., Jiménez-PiquéE., Johansson JöesaarM. P., RoaJ. J., GhafoorN. and OdénM.: ‘Structure, deformation and fracture of arc evaporated Zr-Si-N hard films’, Surf. Coat. Technol., 2014,
258, 1100–1107. doi: 10.1016/j.surfcoat.2014.07.024
35.
BeakeB. D., GarcíaM. J. I. and SmithJ. F.: ‘Micro-impact testing: a new technique for investigating fracture toughness’, Thin Solid Films, 2001,
398–399, 438–443. doi: 10.1016/S0040-6090(01)01397-9
36.
BhowmickS., KaleA. N., JayaramV. and BiswasS. K.: ‘Contact damage in TiN coatings on steel’, Thin Solid Films, 2003,
436, 250–258. doi: 10.1016/S0040-6090(03)00598-4
37.
TilbrookM. T., PatonD. J., XieZ. and HoffmanM.: ‘Microstructural effects on indentation failure mechanisms in TiN coatings: Finite element simulations’, Acta Mater., 2007,
55, 2489–2501. doi: 10.1016/j.actamat.2006.11.043
