Fine-grained 7034 aluminium alloys were soldered with Zn–5Al filler metals, using liquid Ga as protective coatings to remove oxide films of the base and filler metals and prevent secondary oxidation. Holding times and coating modes were adjusted by experiments. Applying the Ga coating on both the base and filler metals caused the Ga enrichment in the α-Al particles and the formation of Mg2Ga5 intermetallic compound at the bonding interface, deteriorating joint mechanical performance. Ga enrichment was prevented by applying the coating on the filler metal alone, which avoided the early contact of Ga with Al substrate and reduced the mass of Ga in the joint. The tensile strength increased significantly to 159∼185 MPa with a sufficient holding time.
MaKWenHHuTMechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy. Acta Mater. 2014; 62:141–155. doi:10.1016/j.actamat.2013.09.042.
2.
Rezaee-BazzazAAhmadianSReihaniH.Modeling of microstructure and mechanical behavior of ultra fine grained aluminum produced by accumulative roll-bonding. Mater Des. 2011; 32:4580–4585. doi:10.1016/j.matdes.2011.04.011.
3.
LangYZhouGHouLSignificantly enhanced the ductility of the fine-grained Al-Zn-Mg-Cu alloy by strain-induced precipitation. Mater Des. 2015; 88:625–631. doi:10.1016/j.matdes.2015.09.023.
4.
Nayeb-HashemiHLockwoodM.The effect of processing variables on the microstructures and properties of aluminum brazed joints. J Mater Sci. 2002; 37:3705–3713. doi:10.1023/A:1016517510260.
5.
BazhenovVEPashkovINPikunovMVInteraction of Zn and Zn - 4Al, Zn - 15Al (wt-%) solder alloys with aluminium. Mater Sci Technol (United Kingdom). 2016; 32:752–759. doi:10.1179/1743284715Y.0000000135.
6.
YangJXueSXuePDevelopment of novel CsF-RbF-AlF3 flux for brazing aluminum to stainless steel with Zn-Al filler metal. Mater Des. 2014; 64:110–115. doi:10.1016/j.matdes.2014.07.059.
7.
XiaoBWangDChengFDevelopment of ZrF4-containing CsF-AlF3 flux for brazing 5052 aluminium alloy with Zn-Al filler metal. Mater Des. 2016; 90:610–617. doi:10.1016/j.matdes.2015.11.025.
8.
LiYXZhaoWWLengXSMicrostructure evolution and mechanical properties of ultrasonic-assisted soldering joints of 2024 aluminum alloys. Trans Nonferrous Met Soc China (English Ed). 2011; 21:1937–1943. doi:10.1016/S1003-6326(11)60953-9.
9.
NagaokaTMorisadaYFukusumiMSelection of soldering temperature for ultrasonic-assisted soldering of 5056 aluminum alloy using Zn-Al system solders. J Mater Process Technol. 2011; 211:1534–1539. doi:10.1016/j.jmatprotec.2011.04.004.
10.
GuoWLuanTHeJUltrasonic-assisted soldering of fine-grained 7034 aluminum alloys using ZnAl filler metals. Mater Des. 2017; 125:85–93. doi:10.1016/j.matdes.2017.03.073.
11.
ShafferJMaassenKWilsonCDevelopment of an open-sourced automated ultrasonic-assisted soldering system. J Manuf Process. 2019; 47:284–290. doi:10.1016/j.jmapro.2019.09.007.
12.
Gheybi HashemabadSGuZAndoT.Flux-less direct soldering of aluminum by ultrasonic surface activation. J Mater Process Technol. 2016; 233:135–141. doi:10.1016/j.jmatprotec.2016.02.015.
13.
WanLHuangYHuangTNovel method of fluxless soldering with self-abrasion for fabricating aluminum foam sandwich. J Alloys Compd. 2015; 640:1–7. doi:10.1016/j.jallcom.2015.04.005.
14.
ShirzadiAASaindrenanG.New method for flux free diffusion brazing of aluminium alloys using liquid gallium (UK patent application 0128623.6). Sci Technol Weld Join. 2003; 8:149–153. doi:10.1179/136217103225010871.
15.
FerchaudEChristienFBarnierVCharacterisation of Ga-coated and Ga-brazed aluminium. Mater Charact. 2012; 67:17–26. doi:10.1016/j.matchar.2012.02.013.
16.
NiuTHouHWangYEffect of high uniform magnetic field on joining property and element diffusion of 1420 Al-Li alloy. Trans China Weld Inst. 2016; 37:1–5.
17.
ShimizuTIshikawaHOhnumaIZn-Al-Mg-Ga alloys as Pb-free solder for die-attaching use. J Electron Mater. 1999; 28:1172–1175. doi:10.1007/s11664-999-0153-4.
18.
KravchenkoOVSemenenkoKNBulychevBMActivation of aluminum metal and its reaction with water. J Alloys Compd. 2005; 397:58–62. doi:10.1016/j.jallcom.2004.11.065.
19.
XuZYanJWangCSubstrate oxide undermining by a Zn-Al alloy during wetting of alumina reinforced 6061 Al matrix composite. Mater Chem Phys. 2008; 112:831–837. doi:10.1016/j.matchemphys.2008.06.056.
20.
NamHSSrolovitzDJ.Effect of material properties on liquid metal embrittlement in the Al-Ga system. Acta Mater. 2009; 57:1546–1553. doi:10.1016/j.actamat.2008.11.041.
21.
SenelEWalmsleyJCDiplasSLiquid metal embrittlement of aluminium by segregation of trace element gallium. Corros Sci. 2014; 85:167–173. doi:10.1016/j.corsci.2014.04.012.
22.
ChangCCUanJY.Ductile-to-brittle transition for the aluminum alloy contacting to liquid gallium metal. J Alloys Compd. 2008; 464:146–149. doi:10.1016/j.jallcom.2007.09.115.
23.
RettenmayrMLambrachtPKempfBZn-Al based alloys as Pb-free solders for die attach. J Electron Mater. 2002; 31:278–285. doi:10.1007/s11664-002-0144-1.
24.
ReganMTostmannHPershanPX-ray study of the oxidation of liquid-gallium surfaces. Phys Rev B-Condens Matter Mater Phys. 1997; 55:10786–10790. doi:10.1103/PhysRevB.55.10786.
25.
PlechAKlemradtUMetzgerHIn situ x-ray reflectivity study of the oxidation kinetics of liquid gallium and the liquid alloy Ga0.93Hg0.07. J Phys Condens Matter. 1998; 10:971–982. doi:10.1088/0953-8984/10/5/007.
26.
FlaminiDOSaidmanSBBessoneJB.Aluminium activation produced by gallium. Corros Sci. 2006; 48:1413–1425. doi:10.1016/j.corsci.2005.05.014.
