In this study, the effects of 0.14 wt-% Sn on accelerating the precipitation kinetics during heat treatment are quantified. By calculating the activation energy of θ′ phase, it was found that the combined additions of Cu and Sn can reduce the energy barrier and increase the number density of the θ′ phase in the peak aged state, and thus improving yield strength and ultimate tensile strength from 239 and 318 to 445 and 457 MPa, respectively. Based on the quantitative analysis of the θ′ phase, it was found that with the combined additions of Cu and Sn, the average length of the θ′ phase increased from 18.11 to 25.82 nm, and the number density increased from 2.17 × 1021 to 4.62 × 1021 m−3.
ZhangWLinBZhangDMicrostructures and mechanical properties of squeeze cast Al-5.0Cu-0.6Mn alloys with different Fe content. Mater Des. 2013; 52:225–233.
2.
SofyanBTRaviprasadKRingerSP.Effects of microalloying with Cd and Ag on the precipitation process of Al-4Cu-0.3Mg (wt%) alloy at 200°C. Micron. 2001; 32(8):851–856.
3.
BahlSHuXHoarEEffect of copper content on the tensile elongation of Al-Cu-Mn-Zr alloys: experiments and finite element simulations. Mater Sci Eng A. 2020; 772:138801.
4.
LotterFPetschkeDStaabTEMThe influence of trace elements (In, Sn) on the hardening process of Al-Cu alloys. Phys Status Solidi A. 2018; 215(11).
5.
AkopyanTKBelovNALetyaginNV.Effect of trace addition of Sn on the precipitation hardening in Al-Si-Cu eutectic alloy. Jom. 2019; 71(5):1768–1775.
6.
DaiSBianZWuWThe role of Sn element on the deformation mechanism and precipitation behavior of the Al-Cu-Mg alloy. Mater Sci Eng A. 2020; 792:139838.
7.
LotterFPetschkeDDe GeuserFIn situ natural ageing of Al-Cu-(Mg) alloys: The effect of In and Sn on the very early stages of decomposition. Scr Mater. 2019; 168:104–107.
8.
JohnsonWAMehlRF.Reaction kinetics in processes of nucleation and growth. Am Inst Min Metall Pet Eng. 1939; 135(8):416–442.
9.
AvramiM.Kinetics of phase change. I. General theory. J Chem Phys. 1939; 7(12):1103–1112.
10.
LiHYanZCaoL.Bake hardening behavior and precipitation kinetic of a novel Al-Mg-Si-Cu aluminum alloy for lightweight automotive body. Mater Sci Eng A. 2018; 728:88–94.
11.
LuoALloydDJGuptaAPrecipitation and dissolution kinetics in Al-Li-Cu-Mg alloy 8090. Acta Metall Mater. 1993; 41(3):769–776.
12.
YuanBGuoMWuYInfluence of treatment pathways on the precipitation behaviors of Al-Mg-Si-Cu-(Zn)-Mn alloys. J Alloys Compd. 2019; 797:26–38.
13.
HutchinsonCGouneMRedjaimiaA.Selecting non-isothermal heat treatment schedules for precipitation hardening systems: An example of coupled process-property optimization. Acta Mater. 2007; 55(1):213–223.
14.
SjölanderESeifeddineS.The heat treatment of Al-Si-Cu-Mg casting alloys. J Mater Process Technol. 2010; 210(10):1249–1259.
15.
BhatTBArunachalamVS.Strengthening mechanisms in alloys. Sadhana Acad Proc Eng Sci. 1980; 3(4):275–296.
16.
GazizovMKaibyshevR.Precipitation structure and strengthening mechanisms in an Al-Cu-Mg-Ag alloy. Mater Sci Eng A. 2017; 702:29–40.
17.
DorinTRamajayamMLambJEffect of Sc and Zr additions on the microstructure/strength of Al-Cu binary alloys. Mater Sci Eng A. 2017; 707:58–64.
18.
CaoYChenXWangZEffect of Cd micro-addition on microstructure and mechanical properties in ternary Al-Si-Cu alloy. J Alloys Compd. 2021; 851.
19.
NieJFMuddleBC.Strengthening of an Al-Cu-Sn alloy by deformation-resistant precipitate plates. Acta Mater. 2008; 56(14):3490–3501.
20.
WangXMShaoWZJiangJTQuantitative analysis of the influences of pre-treatments on the microstructure evolution and mechanical properties during artificial ageing of an Al-Cu-Li-Mg-Ag alloy. Mater Sci Eng A. 2020; 782:139253.1–139253.19.
21.
WangFQiuDLiuZ-LThe grain refinement mechanism of cast aluminium by zirconium. Acta Mater. 2013; 61(15):5636–5645.
22.
CeschiniLMorriAMorriACorrelation between ultimate tensile strength and solidification microstructure for the sand cast A357 aluminium alloy. Mater Des. 2009; 30(10):4525–4531.
23.
GranulationAMChangeP.Granulation, phase change, and microstructure kinetics of phase change III. J Chem Phys. 1941; 9(2):177–184.
24.
MartoranoMABiscuolaVB.Predicting the columnar-to-equiaxed transition for a distribution of nucleation undercoolings. Acta Mater. 2009; 57(2):607–615.
25.
EastonMStjohnD.Grain refinement of aluminum alloys: part I. The nucleant and solute paradigms-a review of the literature. Metall Mater Trans A. 1999; 30(6):1613–1623.
26.
YangYYuKLiYEvolution of nickel-rich phases in Al-Si-Cu-Ni-Mg piston alloys with different Cu additions. Mater Des. 2012; 33:220–225.
27.
DuJDingDZhangWEffect of Ce addition on the microstructure and properties of Al-Cu-Mn-Mg-Fe lithium battery shell alloy. Mater Charact. 2018; 142:252–260.
28.
ZamaniMToschiSMorriAOptimisation of heat treatment of Al-Cu-(Mg-Ag) cast alloys. J Therm Anal Calorim. 2019; 139(6):3427–3440.
29.
ZhaoYWangZZhangCSynchrotron X-ray tomography investigation of 3D morphologies of intermetallic phases and pores and their effect on the mechanical properties of cast Al-Cu alloys. J Alloys Compd. 2019; 777:1054–1065.
30.
ZhaoYDuWKoeB3D characterisation of the Fe-rich intermetallic phases in recycled Al alloys by synchrotron X-ray microtomography and skeletonisation. Scr Mater. 2018; 146:321–326.
31.
BourgeoisLDwyerCWeylandMStructure and energetics of the coherent interface between the θ′ precipitate phase and aluminium in Al-Cu. Acta Mater. 2011; 59(18):7043–7050.
WolvertonC.Solute-vacancy binding in aluminum. Acta Mater. 2007; 55(17):5867–5872.
34.
KimuraHHasigutiRK.Interaction of vacancies with Sn atoms and the rate of GP zone formation in an Al-Cu-Sn alloy. Acta Metall. 1961; 9(12):1076–1078.
35.
ChenJLLiaoHCWuYNContributions to high temperature strengthening from three types of heat-resistant phases formed during solidifcation, solution treatment and ageing treatment of Al-Cu-Mn-Ni alloys respectively. Mater Sci Eng A. 2020; 772:138819.
36.
ZhuXHLinYCWuQEffects of aging on precipitation behavior and mechanical properties of a tensile deformed Al-Cu alloy. J Alloys Compd. 2020; 843:155975.
37.
BartgesCWLinJS.Effect of Sn additions on GP zone formation in Al-Cu alloys. Scr Metall Mater. 1993; 28(10):1283–1286.
38.
JungJGParkJSLeeYK.Quantitative analyses of dissolution and precipitation kinetics of θ-Al2Cu phase in an Al-6.2Si-2.9Cu alloy using electrical resistivity. Met Mater Int. 2013; 19(2):147–152.
39.
KarovJYoudelisWV.Growth kinetics of θ′-and θ-phases in Al-3Cu alloy. Mater Sci Technol. 2013; 2(12):1183–1188.
40.
StarkeEAJr, StaleyJT.Application of modern aluminum alloys to aircraft. Prog Aerosp Sci. 1996; 32(2):131–172.
41.
ZaWJeaS.Strengthening effect of unshearable particles of finite size: A computer experimental study. Acta Mater. 1999; 47(11):3263–3269.
42.
ZhuAWChenJ S JEA.Precipitation strengthening of stress-aged Al-xCu alloys. Acta Mater. 2000; 48(9):2239–2246.
43.
HolmedalB.Strength contributions from precipitates. Philos Mag Lett. 2015; 95(12):594–601.
