Surface metal matrix composites have been developed to enhance properties such as erosion, wear and corrosion of alloys. In this study, ∼5 µm or ∼75 SiC particulates were preplaced on a microalloyed steel. Single track surface zones were melted by a tungsten inert gas torch, and the effect of two heat inputs, 420 and 840 J mm−1, compared. The results showed that the samples melted using 420 J mm−1 were crack-free. Pin-on-disk wear testing under dry sliding conditions was conducted. The effects of load and sliding velocity were used to characterise the performance of the crack-free samples. Microstructural and X-ray diffraction studies of the surface showed that the SiC had dissolved, and that martensite, was the main phase influencing the hardness.
BachRDamascheckEGeisslerELaser transformation of different steels. In: BergmannHWKupferR, editors. Proceedings of the 3rd European conference on Laser Treatment of Materials (ECLAT’90). Coberg: Sprwechsaal Publishing Group; 1990. p. 265–282.
2.
SongYBakerTN.A calorimetric and metallographic study of precipitation process in AA6061 and its composites. Mater Sci Eng A. 1995; 201:251–260. doi: 10.1016/0921-5093(95)09781-3
3.
GurcanABBakerTN.Wear behavior of AA6061 aluminum-alloy and its composites. Wear. 1995; 188:185–191. doi: 10.1016/0043-1648(95)06639-X
4.
DaoudAAbou El-khairMT.Wear and friction behavior of sand cast brake rotor made of A359-20vol%SiC particle composites sliding against automobile friction material. Tribo Int. 2010; 43:544–553. doi: 10.1016/j.triboint.2009.09.003
5.
RaoRNDasS.Effect of matrix alloy and influence of SiC particle on the sliding wear characteristics of aluminium alloy composites. Mater Des. 2010; 31:1200–1207. doi: 10.1016/j.matdes.2009.09.032
6.
SinghJChauhanA.Overview of wear performance of aluminium metal matrix conposities reinforced with ceramic material under the influence of controllable variables. Ceram Int. 2016; 42:56–81. doi: 10.1016/j.ceramint.2015.08.150
7.
ShabaniM-DPaydarMHZamiriRMicrostructural and sliding wear behavior of SiC-particle reinforced copper matrix composites fabricated by sintering and sinter-forging processes. J Mater Res Technol. 2016; 5:5–12. doi: 10.1016/j.jmrt.2015.03.002
8.
IonJC.Laser processing of engineering materials. Amsterdam: Elsevier; 2005. p. 261–326.
9.
ZhongMLiuW.Laser surface cladding: the state of the art and challenges. Proc Inst Mech Eng Part C J Mech Eng Sci. 2010; 224:1041–1062. doi: 10.1243/09544062JMES1782
10.
BakerTN.Laser surface modification of titanium alloys. In: DongH, editor. Surface engineering of light alloys. Oxford: Woodhead Publishing; 2010. p. 398–443.
11.
AyersJDSchaeferRJ.In: Ready JF, editor. Proceedings of the Conference of Laser applications in material processes. Bellingham: SPIE; 1979. p. 57–64.
AyersJDSchaeferRJRobeyWP.A laser processing technique for improving the wear-resistance of metals. J Met. 1981; 33:19–23.
14.
AyersJDBolsterRN.Abrasive wear with fine diamond particles of carbide-containing aluminum and titanium-alloy surfaces. Wear. 1984; 93:193–205. doi: 10.1016/0043-1648(84)90069-3
15.
MridhaSBakerTN.Metal matrix composite layer formation with 3 mu SiCp powder on IMI318 titanium alloy surfaces through laser treatment. J Mater Process Technol. 1997; 63:432–437. doi: 10.1016/S0924-0136(96)02660-X
16.
ArchardJFHirstW.The wear of metals under unlubricated conditions. Proc R Soc Lond. 1956; 236A:397–410.
17.
AbboudJHWestDRF.Microstructure of titanium injected with SiC particles by laser processing. J Mater Sci Lett. 1991; 10:1149–1152. doi: 10.1007/BF00744110
18.
BakerTNXinHHuCDesign of surface in-situ metal-ceramic composite formation via laser treatment. Mater Sci Technol. 1994; 10:536–544. doi: 10.1179/mst.1994.10.6.536
19.
MridhaSBakerTN.Metal matrix composite layers formed by laser processing of commercial purity Ti-SiC in nitrogen environment. Mater Sci Technol. 1996; 12:595–602. doi: 10.1179/026708396790165984
20.
HuCBarnardLMridhaSThe role of SiC particulate and Al2O3 (Saffil) fibers in several alloys during the formation of in situ MMCs developed by laser processing. J Mater Process Technol. 1996; 58:87–95. doi: 10.1016/0924-0136(95)02111-6
21.
TerryBChinyamakobvuOS.Assessment of the reaction of SiC powders with iron-based alloys. J Mater Sci. 1993; 28:6779–6784. doi: 10.1007/BF00356431
22.
PellegJ.Reactions in the matrix and interface of Fe-SiC metal matrix composite system. Mater Sci Eng. 1999; A269:225–241. doi: 10.1016/S0921-5093(99)00158-6
23.
GemelliEGallerieACailletM.Improvement of resistance of oxidation by laser alloying on a tool steel surface. Scr Mater. 1998; 39:1345–1352. doi: 10.1016/S1359-6462(98)00329-7
ZhangCPeiSJiHFabrication of Ni60–SiC coating on carbon steel for improving friction, corrosion properties. Mater Sci Technol. 2017; 33:446–453. doi: 10.1080/02670836.2016.1224216
26.
MajumdarJDChandraaBRNathAKStudies on compositionally graded silicon carbide dispersed composite surface on mild steel developed by laser surface cladding. J Mater Process Technol. 2008; 203:505–512. doi: 10.1016/j.jmatprotec.2007.10.056
27.
MridhaSNgB.Addition of ceramic particles to GTAW melted titanium surfaces. Surf Eng. 1999; 15:210–215. doi: 10.1179/026708499101516533
28.
BuytozS.Microstructural properties of SiC based hardfacing on low alloy steel. Surf Coat Technol. 2006; 200:3734–3742. doi: 10.1016/j.surfcoat.2005.01.106
29.
ReddyGSArulSSellamuthuR.Improving surface hardness of mild steel plates by addition of silicon carbide using gas tungsten arc as heat source. Appl Mech Mater. 2014; 592–594:879–882. doi: 10.4028/www.scientific.net/AMM.592-594.879
30.
PatelPMridhaSBakerTN.Influence of shielding gases on preheat produced in surface coatings incorporating SiC particulates into microalloy steel using TIG technique. Mater Sci Technol. 2014; 30:1506–1514. doi: 10.1179/1743284713Y.0000000481
31.
Muñoz-EscalonaPMridhaSBakerTN.Effect of shielding gas on the properties and microstructure of melted steel surface with a TIG torch. Adv Mater Process Technol. 2015; 1:435–443.
ChoiYLiuR.Performance of nano/micro CBN particle coated tools in superfinish hard machining. Int J Mac Tools Manuf. 2009; 49:683–689. doi: 10.1016/j.ijmachtools.2009.03.005
35.
UhlmanEOyane del FuentesJAKeuneckeM.Machining of high performance workpiece materials with CBN coated cutting tools. Thin Solid Films. 2009; 518:1451–1454. doi: 10.1016/j.tsf.2009.09.095
de Escalona PMMridhaSBakerTN.Effect of silicon carbide size particle on the properties and microstructure of melted steel surface using TIG torch. Adv Mater Process Technol. 2016; 2:451–460.
38.
EasterlingKE.Introduction to physical metallurgy of welding. London: Butterworth-Heinemann; 1992.
39.
RasoolGStackMM.Wear maps for TiC composite based coatings deposited on 303 stainless steel. Tribo Int. 2014; 74:93–102. doi: 10.1016/j.triboint.2014.02.002
40.
HuCBakerTN.The importance of preheat before laser nitriding a Ti-6Al-4V alloy. Mater Sci Eng A. 1999; 265:268–275. doi: 10.1016/S0921-5093(98)01135-6
41.
Kotecki DJCheeverDLHowdenDG.Mechanism of ripple formation during weld solidification. Weld J. 1972; 51:386S–391S.
42.
KouSLimmaneevichitrCWei PS.Oscillatory Marangoni flow: a fundamental study by conduction-mode laser spot welding. Weld J. 2011; 90:229S–240S.
43.
PeiYTOuyangJHLeiTCMicrostructure of laser-clad SiC-(Ni alloy) composite coating. Mater Sci. Eng. 1995; 194A:219–224. doi: 10.1016/0921-5093(94)09653-8
44.
TewariSPGuptaAPrakashJ.Effect of welding parameters on the weldability of material. Int J Eng Sci Technol. 2010; 2:512–516.
GhoshPKKumarR.Surface modification of micro-alloyed high strength low alloy steel by controlled TIG arc process. Metall Mater Trans A. 2015; 46A:831–842. doi: 10.1007/s11661-014-2670-x
47.
MridhaSBaker TN.Crack-free hard surfaces produced by laser nitriding of commercial purity titanium. Mater Sci Eng. 1994; A188:229–239. doi: 10.1016/0921-5093(94)90376-X
48.
DePondPJGussGLySIn situ measurements of layer roughness during laser powder bed fusion additive manufacturing using low coherence scanning interferometry. Mater Des. 2018; 154:347–359. doi: 10.1016/j.matdes.2018.05.050
49.
TangWMZhengZXDingHFA study of the solid state reaction between silicon carbide and iron. Mater Chem Phys. 2002; 74:258–264. doi: 10.1016/S0254-0584(01)00480-1
50.
KawanishiSYoshikawaTTanakaT.Equilibrium phase relationship between SiC and a liquid phase in the Fe-Si-C system at 1523-1723K. Mater Trans. 2009; 50:806–813. doi: 10.2320/matertrans.MRA2008404
51.
RunnsjöG.On the accuracy of carbon determinations in steels by electron probe microanalysis. Scan J Metall. 1980; 9:199–203.
52.
GoldsteinJINewburyDEEchlinPScanning electron microscopy and X-ray microanalysis. New York: Plenum Press; 1984.
53.
CavaRDBottaWJKiminamiCSOrdered phases and texture in spray-formed Fe–5wt%Si. J Alloys Compds. 2011; 509S:S260–S264. doi: 10.1016/j.jallcom.2010.11.184
54.
JangPChoiG.Effects of silicon content on the properties of gas-atomized Fe–Si–Cr powders. IEEE Trans Mag. 2017; 53:2002705.
55.
BainEC.Functions of alloying elements in steels. Cleveland: ASM; 1939.
56.
PickeringFBGladmanT.An investigation into some factors which control the strength of carbon steels. In Metallurgical developments in carbon steels, Sp. Report 81, ISI, London, UK; 1963. p. 11–20.
57.
MillsKCKeeneBJBrooksRFMarangoni effects in welding. Proc R Soc London A. 1998; 356A:911–925. doi: 10.1098/rsta.1998.0196
